Miele CVA 4075 EN-CA User manual

Installation Instructions

CVA 4075 en-CA

Installation, repair and maintenance work should be performed by

a Miele authorized service technician in accordance with national

and local safety regulations and the provided installation instructions.

The machine must be connected to

the water supply in accordance with

local and national regulations.

The water being used should have

the drinking water standards of the

respective country where the

machine is used.

– All units and systems used to deliver

the water to the coffee system must

conform with the requirements of the

respective country.

– The machine is designed to be

plumbed to a cold water connection.

– The machine can be connected

without a non-return valve.

– The on-site water line must have a

water valve to turn the water off if

needed. If not present, have a water

valve installed by a licensed

plumber.

– The water faucet must be accessible

after installation.

– Water pressure on-site:

Minimum: 14.5 psi

Maximum: 145 psi, if higher, install a

pressure reduction valve.

– Suitable 1/4" tubing or copper piping

must be supplied for plumbing.

– To ensure the best coffee quality, the

maximum length of the tubing or

copper pipe should not exceed

4 ft. 11" (1.5 m). If too much water

remains in the tubing the coffee

quality could be affected.

Connection to the water

supply

^Disconnect the machine from the

electrical supply.

^Remove the water connection cover

at the lower rear side of the coffee

machine.

^Screw the supplied brass

compression fitting, with the ¾" end,

tightly onto the water connector of the

coffee machine. The fitting includes

an opening for standard ¼" piping.

^Connect the compression fitting to

the water supply.

^Check for leaks.

Plumbing

Ensure that power is not supplied to

the machine while installation or

maintenance work is performed.

All electrical work should be

performed by a qualified electrician

in strict accordance with national

and local safety regulations.

Installation, repairs and other work

by unqualified persons could be

dangerous.

The manufacturer cannot be held

responsible for unauthorized work.

Verify that the voltage, load and circuit

rating information found on the data

plate match the household electrical

supply before installing the coffee

system.

If there is any question concerning the

electrical connection of this appliance

to your power supply, please consult a

licensed electrician or contact Miele’s

Technical Service Department. See

back page for contact information.

WARNING:

THIS APPLIANCE MUST BE

GROUNDED

Important

The coffee system comes equipped

witha6ft(1.8 m) power cord with a

NEMA 5-15P molded plug for

connection to a 120 V, 15 A, 60 Hz

power supply.

Electrical connection

Installation options

The coffee system is designed to be

built into cabinetry.

A combination with other Miele built in

appliances is possible. If the machine

is installed in combination with other

appliances, it should be installed with a

protective base between the appliance

and the unit (exception: installation with

a built-in plate warmer).

A special display cabinet is also

available from your dealer or Miele, as

an installation option.

Installation

Make sure power is not supplied to

the appliance while installation or

maintenance work is performed.

Disconnect the power supply to the

work area by unplugging the unit,

tripping the circuit breaker or

removing the fuse. The coffee

system must be installed into

cabinetry before being used.

^Unscrew the height adjustable feet

on the underside of the machine

about 1/16" (2 mm).

^Push the appliance all the way back

into the cabinet and center it. If

necessary level the unit with the four

height adjustable feet.

The feet can be turned out up to 3/8"

(10 mm).

^If your cabinet has 3/4" (19 mm) side

walls, drill four holes for the

mounting.

^Center the unit and turn the screws a

little bit in and then out again.

^Take the unit out of the niche and drill

four holes at the screw markings

(1/16" [2 mm], diameter 3/16"

[4.5 mm]).

^Connect the appliance to a cold

water supply.

^Plug the appliance into the electrical

outlet.

^Push the appliance into the niche.

^Open the door and partially tighten

the screws.

^Carefully turn the lower screws, a,to

center the machine.

^To secure the appliance in the

cabinet, tighten the upper screws, b,

by hand. Do not use an electric

screwdriver.

Installation

Adjusting the door hinges

The door hinges can be adjusted if the

door cannot be opened easily.

^To adjust the door sideways, a, turn

screw a.

^To adjust the door to the front or

back, b, turn screw b.

Installation

M.-Nr. 06 984 320 / 03

Alteration rights reserved / 2707

with convertible water connection

CVA 4075

For the most updated manual see the Miele website.

This manual suits for next models

Table of contents

Popular Coffee Maker manuals by other brands

Taurus

Taurus Livorno 6 manual

Delta-q

Delta-q QUICK instruction manual

Bunn

Bunn LCA-1 Installation & operating guide

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Use and care book

Saeco

Saeco Vienna Plus Sup 018M operating instructions

DeLonghi

DeLonghi DC300 Owner's instructions

INCAPTO

INCAPTO BXCO1470E Instructions for use

Bosch

Bosch TASSIMO finesse TAS16B Series user manual

Exido

Exido 245-072 Specifications

Animo

Animo OptiVend Choco user manual

Siemens

Siemens TQ505DF Series user manual

DeLonghi

DeLonghi ECI341 Instructions for use

Krups

Krups KT406511 manual

Cimbali

Cimbali M32 Classic manual

Philips

Philips HL3844N Service manual

Bosch

Bosch TES 515 SERIES instruction manual

Tekmatix

Tekmatix TMFM - 65 Operation manual

Scarlett

Scarlett SC-CM33005 instruction manual