Midea DSK45V User manual

Thank you very much for purchasing our water heater.

Before installing and operating your water heater, please

read this manual carefully and keep it for future reference.

The diagram above is just for reference. Please take the

appearance of the actual product as the standard.

Instant Electric Water Heater

Instruction Manual

Model: DSK45V

TABLE OF CONTENTS

TITLE PAGE

1.Cautions ...........................................................................................................................(2)

2.Product introduction .........................................................................................................(3)

3.Unit installation .................................................................................................................(5)

4.Methods of using ..............................................................................................................(8)

5.Maintenance.....................................................................................................................(9)

6.Troubleshooting..............................................................................................................(10)

Sincerely thank you for selecting our electric water heater. Please read this manual carefully

before use; correctly grasp the methods for installation and use of this electrical water heater, to

make full use of its excellent performances. Please do preserve the instruction manual for future

reference.

This water heater is for household, and it can be installed wherever place that need hot water.

Plug is not used for this water heater; this water heater must be connected directly with power

switch that comes with leakage-protection. Please distinguish live line (red/brown), neutral line

(blue) and earth line (green/yellow) during installation.

Do check whether the amperes of the household wiring enough before installation, and

dedicated circuit must be used when installation.

Before installing this water heater, check and confirm the earth electrode on the socket is reliably

earthed, without electricity.

The hot water from the water heater may cause scald, please test the temperature of the hot

water before use.

The distance between water heater installed and water output should be as nearby as possible

to avoid loss of heat.

The electric water heater may be damaged if the water hardness is too high. To ensure longer

product lifespan, please install and put it into use on condition that the local water hardness is

less than 450mg/L (CaCO3)

In time of lightning/thunder, switch “Off” the Miniature Circuit Breaker (MCB) in advance to

protect the water heater against possible damage.

Inspection on the built-in ELCB (once a month) to avoid a hazard to users such as damage to

property, serious injury or death.

Do cut-off power supply before any maintenance. Any maintenance or adjustment towards this

product by non-professional is highly prohibited.

The damage power cord must be replaced by a good power cord provided by the manufacturer,

and the replacement should be done by a qualified technician or engineer or professionals of

the similar products.

In order to avoid a hazard due to inadvertent resetting of the Earth Leakage Circuit Breaker

(ELCB), this appliance must not be supplied through an external switching device, such as timer

or connected to a circuit that is regularly switched “On” and “Off” by the utility.

Water heater is equipped with adjustable flow capacity safety valve. For safety use, please do

not change its installation location and do not block its water outlet.

For any improper installation and incorrect operation of this product, our company will not be

liable for any responsibility.

This water heater can be used for other purpose, eg. Washing hands, dishes or foods, and so on.

(Multi directional water supply is not available).

When the shower is used by someone such as child, old person, sick person and physical

handicapped person, the concern person is kindly requested to pay attention and check the

shower temperature by using hand from time to time.

To prevent personal injury, injury to others and property damage, the instructions below must be

followed. Incorrect operation due to failure to follow instructions will cause harm or damage.

Special Cautions

1. CAUTIONS

●

WARNING

The water heater should be earthed before use. Please ensure that the resistance of

household earth wire is <4Ω. Using water heater without earthed is highly prohibited.

2. PRODUCT INTRODUCTION

Model

Rated Voltage

Rated Frequency

Rated Power

Rated Current

Dia. Of Wire Code

Air Switch

Rated Pressure

Minimum Flow Rate

Minimum Pressure

Maximum Pressure

Protection Class

Water Proof Class

Products Size

Knob Quantity

DSK45V

220-240V~

50/60Hz

4500W

20.4A

2.5mm²

≥25A

0 MPa

1.5 Liters/minute

0.03 MPa

0.3 MPa

IP25

224×330×93 mm

2.1 Technical Performance Parameters

2.2 Parts Identification

WIRING DIAGRAM

2.3 Internal Wire Diagram

Indicator Light Board

Thermal

Cut Out

Key Board

Red

Blue

Yellow/Green

Temperature

Adjusting Board

Heating Elements

Silicon Control

Main Control Board

Relay

Flow Sensor

Temperature Sensor

Terminal Block

CN1 CN4 CN6

CN2

CN3

CN5

ELCB

Terminal block

Indicator light

board

Main control board

Silicon control

Flow sensor

Marker for

water inlet

Water inlet

Wire pressing board

Thermal

cut out

Heating

elements

assembly

Stainless

steel circlip

Marker for

wateroutlet

Water outlet

Key board

Red Blue

3.1 Installation Instruction

3.2 Power Cord Installation

Check the capacity of power circuit;

Power cord installation;

Water heater installation;

Plumbing connection;

Power supply connection;

①

②

③

④

⑤

Water Supply.

Step 1 Step 2

⑥

3. UNIT INSTALLATION

Step 3 Step 4

Step 5 Step 6

Remove the screws at the bottom of the unit. Lift

up the Main Switch Knob and Power Knob to

make it free. Remove the front plate gently.

Gash the middle of the film of the power cord

jacket with a sharp knife in order to put into

power lines.

Tighten the wire-pressing plate with screws to

primary position, ensure that the power cord not

be pulled out more than 60N.

Remove the power cord wire pressing plate and

keep the screws.

Screw the power cord into the jacket for

installation of wire pressing plate.

Connect the power cord to wiring terminals; the

method is as shown in picture.

3.3 Water Heater Installation

3.4 Plumbing Connection

①

②

③

④

⑤

NOTE

The installation position of neutral line (blue), live line (brown/red) and earth line

(green/yellow) should be corresponding to the other end on wiring terminals.

Make sure the distance between the unit and surrounding wall is not less than 300mm, so

that to have enough space for maintenance purpose.

Determinethe position of four fixing screws (attached with the unit), make four holes with

corresponding depth in the wall by means of a drill and drive a wall plug into the hole.

Drive in the screws on the top and ensure certain distance between screw head and wall

(See Fig.1)

Mount the unit on the wall and tighten with two screws at bottom, connect the wires and

install top cover with the screws.

Determine installation position of the unit according to length of power cord / position

of air switch (Distance between bottom and floor should be ≥1.6m).

①

②

Shower flexible tube should be connected with water outlets and shower head separately,

attached sealing ring should be used at end face.

Water valve with filter should be installed at water inlet of the unit, sealing ring with filter

should be used at end face. (See Fig.2).

120

250

180

(Fig.1)

WARNING

Metallic / chromed hose and conductive control valve shall not be used.

3.5 Power Supply Connection

3.6 Water Supply

①

②

③

Choose air switch with leakage protection according to power of water heater;

When connecting the water heater to electric network, please pay attention to connect live

line (red/brown), neutral line (blue) and earth line (yellow/green) with corresponding line in

electric network.

Adjust power selection knob to“OFF”;

(Fig.2)

Water flow adjusting

valve with filter

Cold water inlet

NOTE

Water flow adjusting valve with filter must be used when install the unit. Blue marker

stands for water inlet, red marker stands for water outlet. Do not overexert to avoid

damaging the water heater.

NOTE

A private power cord should be used for this unit. After connecting to electric network,

please check the earth condition and make sure the earth resistance is <4Ω.

After all the plumbing is

finished

connecting, open water inlet valve of the product and supply

water to the unit to drain away air inside until there is stable water flow comes out from shower

head. Check whether there is leakage at joints or not. If there is, check whether the connecting

parts are fastened or not, then re-supply water.

4.1 Operating Of The Unit

4.2 Leakage Testing

4.3 To Adjust Water Flow

Switch on the power supply, the unit will take self-inspection for 2s, The

indicator light will turn blue (under the condition of no electricity leakage).

When the water flow exceeds 1.2L/min, rotate the knob clockwise to switch on

heating power rotate switch, the indicator light will turn white ,the unit start to

work.

4. METHODS OF USING

When the water heater is working normally (including working state of PUMP),

press TEST button, if the leakage test circuit is no problem, the indicator light

will be off, and the unit will not heat. Press RESET, testing will be canceled,

and indicator light will turn blue or white, the unit will be back to working state

set before. If the circuit leaks, press RESET button can't cancel leakagetesting,

the indicator light keeps off, it means the water heater has problems and can't

be used; all the buttons are invalid, the indicator lights are all off, heating is

stopped, and pump will be closed.

Rotate the handle of water flow adjusting valve to adjust the water flow.

4.4 Electricity Leakage Protection

When the electricity leakage testing circuit is working normally, if the leakage current is bigger than

certain value between 7.5mA and 15mA, the indicator light will keep flickering, no heating; it can

only be used after the failure is excluded. (When electricity leakage is tested, red and green

indicator lights are all off, stop heating )

4.5 To Adjust Water Temperature

NOTE

For first time using, ensure electrify after the unit is filled fully with water and there is

stable water flow comes out from shower head.

The electric water heater may be damaged if the water hardness is too high. To

guarantee the normal service life, please install and put it into use on condition that the

local water hardness is less than 450mg/L (CaCO3).

If the water flow is small and power is high while using the unit, outlet water temperature is rather

high; the unit will stop heating automatically. At this time, please lower the power and adjust the

water flow faster in order to avoid inconsistency of water temperature.

4.6 Use After Overheating Protection

Rotate the handle of water flow adjusting valve to adjust to proper water flow. Adjust power by rotating

knob, clockwise rotate, power will be increased and water temperature increase accordingly or vice

versa.

Indicator

light

This electric water heater should be installed at the place without sunshine or rain spray.

Please cut off power supply if not use for long time.

Please blow down the water for about 10 seconds to drain away the impurities in the pipe before

connecting the water source to the electric water heater to avoid blockage of water heater.

If long time no use the unit, check the water heater first before use. Electrify after the water

flows out stably.

Do not spray water to air switch or heater body directly, to avoid moist.

Please cut off the power in the weather of thunder and rain to avoid damaging the water heater.

If not use for long period of time, please cut off water inlet to prolong the lifespan of the water

heater.

Check the power cord connecting terminals frequently to make sure that they are well and

reliablycontacted, no overheating phenomenon,and grounding is good or not.

Disassembly shower head and sealing ring with filter to clean periodically.

DECLARATION: this water heater can only be maintained by authorized service personnel,

incorrect installation and using method may cause serious injury or loss of property.

●

5. MAINTENANCE

WARNING

Do cut off power supply before maintenance, to avoid danger like electric shock.

Table of contents

Other Midea Water Heater manuals

Midea

Midea D15-20VA User manual

Midea

Midea HORIZONTAL Series User manual

Midea

Midea LRSJ-60/NYN1-A1 User manual

Midea

Midea HP170 Operating and safety instructions

Midea

Midea M20 Operating instructions

Midea

Midea DSK45P5 User manual

Midea

Midea CE-LRSJF-V120/N1-610 User manual

Midea

Midea MSH-30VH User manual

Midea

Midea JSG52-26VH3 User manual

Midea

Midea D30-15FG User manual

Midea

Midea JSQ Series User manual

Midea

Midea D30-15W User manual

Midea

Midea JSD12-6DH4 User manual

Midea

Midea M2005 Operating instructions

Midea

Midea M26i User manual

Midea

Midea DSK45U5 User manual

Midea

Midea DSK70035-J User manual

Midea

Midea ECOHEAT Series User manual

Midea

Midea ECOHEAT Series User manual

Midea

Midea HP170 Operating and safety instructions

Midea

Midea DSK45Q User manual

Midea

Midea MWH-38P3 User manual

Midea

Midea RSJ-100/N1-540V-D User manual

Midea

Midea MWH-38Q User manual

Popular Water Heater manuals by other brands

Kenmore

Kenmore 153.582400 Use & care guide

Applimo

Applimo Edel AIR Installation and operating instructions

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Operating and installation instructions

clage

clage E-Mini Series Operating and installation instructions

Toyotomi

Toyotomi Oil Miser OM-180 installation manual

Bradford White

Bradford White EF Series Service manual

Eccotemp

Eccotemp 40-H Use & care manual

Dimplex

Dimplex ECSd125-580 Installation and user instructions

Dux

Dux 32FCR6N installation manual

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Operation and maintenance instructions

Noritz

Noritz N-132M Owner's guide and installation manual

TESY

TESY GCV7/4S 10047 Instructions for use and maintenance

A.O. Smith

A.O. Smith Gphe 50 instruction manual

Koryo

Koryo KWHZF15Y user manual

Pentair

Pentair PSC-14-4-02 Installation and operation manual

GE 40M06AAG Energy guide

Thermor

Thermor AEROMAX SPLIT 2 Instructions for use

American Hometec

American Hometec AHQ-B03X Installation and operation manual