MicroNet SP6008P User manual
Quick Installation Guide
8-Port 10/100M PoE Switch
Model No.: SP6008P
http://www.micronet.info
1
Introduction
The SP6008P supports IEEE 802.3af at standard for Power over
Ethernet (PoE) with the maximum power delivery up to 130 Watts.
That makes it suitable to various applications that demand for
remote power feeding and meet high level requirement for power.
SP6008P is totally equipped with 15.4 Watts per PoE port, which
effectively helps allocate power for connected multiple devices and
enhances network management.
Key Features
yCompliant with IEEE 802.3af standard
ySupports Power over Ethernet on 8 RJ-45 ports of 10/100M
yProvides 130W (max) feeding power to 8 PDs: 15.4W for each
ySupports Auto-MDI/MDI-X
ySupport Non-Blocking Data Forward
ySupports Auto-Negotiation and feature of store-and-forward
yLED indicators for PoE activity
Package Contents
Before you start installing SP6008P, please verify the following
package contents:
ySP6008P 10/100M PoE Switch
yQuick Installation Guide
yPower Cord
yMounting Kits
Tour of the System
Front Panel
LED indicators
Back Panel
Power Switch and Power Cord Connector
LED Indicator
For definitions of LED indicators, please refer to the following table:
LED Status Description
On/Green Power is On.
PWR Off Power is off.
On/Green The Ethernet port is connecting with
the device.
Blink/Green Receiving or transmitting data.
10/100M,
LINK
Off No device attached.
On/Orange PoE port is active.
PoE Off PoE port is not active.
2
3
Hardware Installation
The setup of the switch can be performed using the following steps:
Step 1: Connect the Power Cord to SP6008P and then to a power
outlet.
Step 2: :Connect a RJ-45 Ethernet cable from
IEEE802.3af-compliant devices (PD) to an available PoE
port of SP6005P8.
Note:
Port 1 to Port 8 are used for connecting to PD or PoE splitter for end
devices.
For cable selection, refer to the following table:
Network Speed Cable Type Max. Length
10M Cat. 3,4,5,5e UTP/STP 100 meters
100M Cat. 5,5e UTP/STP 100 meters
Note: To prevent costly equipment damage and downtime, please
consider installing a surge suppression device or a UPS
(Un-interrupted Power Supply).
4
Specification
Standards IEEE 802.3af
IEEE 802.3 10 BaseT
IEEE 802.3u 100 BaseTX
IEEE 802.3x Flow Control
Features Number of Ports: 8 PoE/PSE ports
MAC Address: 1k
Buffer Memory: 512 bits
Transmission Method: Store and Forward
Filtering/
Forwarding
Rates
100Mbps port-148,800pps
10Mbps port-14,880pps
Transmission
Media
10 BaseT Cat 3,4,5 UTP/STP
100M BaseTx CAT 5 UTP/STP
LED
Indicators
Per Port: Link/Act, PoE Act/Status
Per Unit: Power
Power
Input/Output
Input: 100~240V/AC, 50~60 Hz
Output: 48V/DC Per Port Output- 15.4W
Max Per Port, 8 Ports at Full 15.4 W Output
Su
pp
orted
5
Power
Consumption
130 Watts (Max)
Dimension 20(H) x 58(W) x 87(D) mm
Temperature Operating: 0~60oC, Storage: -20~90oC
Humidity Operating: 10~90% (Non-Condensing)
FCC Certifications
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at own expense. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility of the essential protection requirement
of Council Directive 89/336/EEC on the approximation of the laws of
the Member States. Company has an on-going policy of upgrading
its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the
latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
P/N: 2300-xxxx
6
Table of contents
Other MicroNet Switch manuals
MicroNet
MicroNet SP218D User manual
MicroNet
MicroNet SP6528 User manual
MicroNet
MicroNet SP6008PWS User manual
MicroNet
MicroNet SP1684B User manual
MicroNet
MicroNet SP6824P User manual
MicroNet
MicroNet SP508C User manual
MicroNet
MicroNet SP6524PWS User manual
MicroNet
MicroNet SP6108I User manual
MicroNet
MicroNet SP6005P4 User manual
MicroNet
MicroNet SP6108WS User manual
MicroNet
MicroNet SP3524A User manual
MicroNet
MicroNet SP508B User manual
MicroNet
MicroNet SP212E User manual
MicroNet
MicroNet SP616R User manual
MicroNet
MicroNet SP1678A User manual
MicroNet
MicroNet SP659C User manual
MicroNet
MicroNet SP6510P8 User manual
MicroNet
MicroNet EtherFast SP624EA User manual
MicroNet
MicroNet SP6008P User manual
MicroNet
MicroNet SP659A User manual
