Storing your Light If you are going to store your Light for an extended period of time, keep it in a cool location (ideally, 71° F or 22° C).
When cleaning the outside of your Light, first shut down your Light and unplug the power cord. Then use a damp, soft, lint-free cloth to clean the lamp exterior. Avoid getting moisture in any openings. Do not spray liquid directly on the lamp. Do not use aerosol
sprays, solvents, or abrasives that might damage the finish.
MicMol. recognizes its responsibility to minimize the environmental impact of its operations and products.
ATTENTION: Never put the light and the smart controller in the water. Doing so will dangerous and damage your light.
NOTICE: Failure to follow these handling instructions could result in damage to your Light or other property.
WARNING: Do not touch the lights body when it working which will generate heat and may let your hands uncomfortable.
WARNING: Make sure all the cables are connected before plug to electricity or will damage your light.
Important Handling Information
Carrying your Light before you move your Light, shut it down and disconnect all cables and cords connected to it. Using power cord Never force a connector into a port. Don't put the power cord into your tank when it connected. When you Setup your Light
please make sure that it locate power supply where it will not be exposed to any water or moisture.
Mount your power supply where it won’t get wet. Include a “drip loop” - a tied loop of cord hanging down below the level of the electrical outlet. That way, if water happens to run down the cord from the tank, it will drip off onto the floor rather than into the
outlet. Drip Loops should always be used to help prevent water from traveling along the cord and coming into contact with an electrical outlet. Drip loops must always be below the level of the outlet. If the plug or outlet does get wet, DO NOT TOUCH the cord.
MicMol and the Environment
Information
MicMol warrants all MicMol products to be free from manufacturing defects for one year from the original
purchase date when purchased through an authorized MicMol retailer. This warranty does not cover any
damages caused by misuse, neglect, alterations or improper handling / transport / maintenance / installation.
Physical damages are not covered by warranty. MicMol does not cover personal injury, personal loss, or other
damages associated with the use of our products. In order to request warranty service, please email us at
[email protected].
A
purchase
receipt
is
required
for
any
warranty
service.
Products
requiring
warranty
service must be returned to MicMol or authorized MicMol retailer. You are responsible for the cost of shipping
a warranty claim to MicMol and any damages that may occur during transit. Once a returned product has
been inspected, it will be repaired or exchanged at our discretion and returned to you. Thank you very much.
Warranty
© 2012~2022 MicMol Limited. All rights reserved.
MicMol, the MicMol Logo, Master, THOR, Air Pro, Aqua CC, Aqua mini, Aqua Pro, Aqua Air, BloomBee are trademarks of MicMol registered.
WWW.MICMOL.COM - MT0010-2209-A Printed in China.
App Controller Overview
Compatible with iOS and Android.
Search “iMicMol” from App Store and Google Play to download directly.
Download APP
Product Name:
Product Mode:
Dealer Name:
Dealer Tel:
Purchase Date:
User Name:
User Tel:
Warranty Card
DCInput
DCOutput
Button
Indicator
Waiting for connect to 100% Great!
You can set your light now. Turn “ON” to control your light
Connecting now....Download and open iMicMol
APP to Add Device
345 6
Choose “Auto Scan”, the device
will appear automatically
Pairing (Please make sure your Bluetooth is turn on. )
Case
Connectivity 2
Systems 2
Dimension
Voltage
Cable Plug
Weight
Controls
Black
Bluetooth2.4G + Broadcast 2.4G
120*20*20 mm
0.2 Kg
DC24V - 1~6A
Standard 5 Pin Waterproof Plug
Hold on 3 Seconds
Factory Reset
iOS + Android
Linkage Mode - Receiver Mode
Triple-Press
Paired + Device is Online
White Constant
Waiting for Pairing
White Flash
Linkage Mode - Receiver Mode
Red Constant
