Michell Instruments S-535 User manual
S-535
Dew Point Adjuster
User Manual
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 2 of 21
Table of Contents :
1. Installing the software.................................................................... 3
2. Connecting the S-535.................................................................... 9
3. Connecting the PC72-Dew Point version .................................... 10
4. Connecting the SF52................................................................... 10
5. Connecting the DT722 ................................................................ 11
6. Start the DP adjuster program..................................................... 12
7. Temperature Calibration.............................................................. 13
8. Modify Calibration Table.............................................................. 14
9. Modify Output.............................................................................. 18
10. Troubleshooting........................................................................... 20
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 3 of 21
1. Installing the software
Suitable for windows7 , 8 and 10
Go to the location of the received software.
Start the installation of the software by double clicking on Setup.exe.
Press Next.
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 4 of 21
Choose the directory where the S-535 program will be installed and press Next.
Accept the license terms and press Next.
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 5 of 21
Below view may be different, depending on the software already installed on your PC.
Press Next to continue.
The installation of the S-535 software will start now.
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 6 of 21
When the installation is complete, press Next.
The S-535 uses the CP210x to communicate with the PC.
The driver will be installed automatically.
In case it doesn’t happen you have to install the driver manually.
Follow the instructions below to install the CP210x USB to UART Bridge Driver
Go to the location of the received software.
Double click on CP210x_VCP_Windows.
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 7 of 21
If you have a PC with a 64bit operating system, double click CP210xVCPInstaller_x64.
if you have a PC with a 32bit operating system, double click CP210xVCPInstaller_x86.
The driver installer starts.
Accept the license terms and press Next to continue.
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 8 of 21
Press Finish to complete the installation.
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 9 of 21
Press Restart to restart your PC , this will complete the installation.
2. Connecting the S-535
Connect the micro-USB cable to the S-535, connect the other side of the cable to a PC.
*Note : Use a (micro)USB-cable of max. 2 meter length !
There are 2 LED’s on the interface,
5V led : must always light up, this is the USB 5V direct from the PC,
if not lit, please check connection to PC.
24V led : must always light up, when this led is getting fainter this means the connected probe is
consuming too much power, and the 24V voltage becomes too low to communicate
with the probe, please check the connected probe.
S-535 Dew Point Adjuster
04 November 2015 WI-NL064_V01 Page 10 of 21
3. Connecting the PC72-Dew Point version
use the 19mm probe adapter cable to connect
the PC72-Dewpoint probe to the S-535 unit.
4. Connecting the SF52
Use the 4 separate wires adapter cable to connect
the DT722 to the S-535 unit.
Connect the SF52 to the adapter cable :
Connect the brown wire of the adapter cable to the white wire of the SF52.
Connect the White wire of the adapter cable to the Green wire of the SF52.
Connect the Blue wire of the adapter cable to the Brown wire of the SF52.
Connect the Black wire of the adapter cable to the Yellow wire of the SF52.
Table of contents
