Metrologic TECH 8 User manual

METROLOGIC INSTRUMENTS, INC.

TECH 8 Laser Bar Code

™

Projection Scanner

Installation and User’s Guide

MLPN 2168

Printed in USA

September1998

Locations:

USA Corporate Headquarters Europe

Metrologic Instruments, Inc. Metrologic Instruments GmbH

Blackwood, NJ 08012 Munich, Germany

Customer Service: 1-800-ID-METRO Tel: 49-89-89018-0

Tel: 609-228-8100 Fax: 49-89-89019-200

Fax: 609-228-6673 ASIA

South America Metrologic Asia (PTE) Ltd.

Metrologic Instruments Singapore 417818

CEP 04571-090, São Paulo-SP, Brasil Tel: 65-842-7155

Outside Brazil: Fax: 65-842-7166

Tel: 55-11-5505-6568

Fax: 55-11-5505-1681

In Brazil:

Tel: 55-11-5505-2396

Fax: 55-11-5507-2301

reproduced, transmitted, or stored in any form or by any means without prior written consent, except

by reviewer, who may quote brief passages in a review, or provided for in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of their respective companies.

iii

Table of Contents

Unpacking List ............................................................ 1

Introduction .............................................................. 1

Labels ................................................................... 2

Applications and Protocols ................................................... 2

Maintenance .............................................................. 3

Configuration of the Scanner to the Host System ................................... 3

Scanner Connections ........................................................ 4

Attaching the Scanner to the Stand and Work Surface ............................... 5

Scanning Bar Codes ........................................................ 6

Appendix A

Specifications ...................................................... 7, 8

Appendix B

Version A1 Pin Assignments for the Mil spec Connector ....................... 9

Version A15 Pin Assignments for the Mil spec Connector ..................... 10

Appendix C

Warranty and Disclaimer ............................................11, 12

Appendix D

Notices ........................................................ 13, 14

Appendix E

Patents ............................................................ 15

Index ................................................................ 16, 17

Unpacking List

The shipping carton, will contain the following:

!TECH 8 Laser Bar Code Projection Scanner

!Installation and User’s Guide

!ScanSelect™ Scanner Programming Guide

!Communication Cable (optional) or Communication Cable

with Power Supply (optional)

!Stand (optional)

If any item is missing or to order additional items, contact the dealer, distributor or call

Metrologic’s Customer Service Department at 1-800-ID-METRO or 1-800-436-3876.

Introduction

Metrologic’s TECH 8 laser bar code projection scanner is encased in an NEMA-12 steel case. The

scanner’s construction enables the scanner to operate in harsh surroundings, especially industrial

environments. Water-resistant, shock-resistant, and rugged, the TECH 8 scanner is also fast,

aggressive and reliable. It can register bar codes at a range of 203mm - 457mm (8" - 18") and can

autodiscriminate among all common codes.

Among the scanner’s many features is an ASIC (Application Specific Integrated Circuit) in the

decoding system that virtually eliminates misreads and MECCA (Metrologic Enhanced Code

Correcting Algorithm). MECCA enables the scanner to read poorly printed, wrinkled or even torn

bar codes on the first pass.

The scanner has been configured at the time of manufacture based on information supplied at the time

of order.

Labels

One label is found inside the window of the scanner noting that this device is a CDRH Class IIa

laser product and EN 60825-1 LASERKLASSE 1. Also, on the scanner is a label on the back of

the unit. This label contains information such as the model number, the date of manufacture and

the serial number. The following are samples of the labels that are found on the unit.

Applications and Protocols

The following chart lists the version identifiers for all the communication protocols. Listed on

each scanner is a model number. The model number includes the scanner number, revision label,

and denoted version identifier. For example, if the model number is MS870-B1, the scanner is an

MS870, B is the revision level, and 1 is the version identifier.

B UNITS

Scanner Version Communication

Identifier Protocol(s)

MS870 1 RS-232, OCIA

MS870 15 Light Pen Emulation

Maintenance

Smudges or dirt that appears on the scanner window can interfere with proper scanning.

Therefore, the window will need occasional cleaning.

1. Spray glass cleaner onto lint free, non-abrasive cleaning cloth.

2. Gently wipe the scanner window.

Configuration of the Scanner to the Host System

The scanner has been configured at the time of manufacture based on information supplied at the

time of order. If ScanSet™ is being used, refer to the ScanSet documentation for information on

how to configure your scanner.

Scanner Connections

In order for the scanner to maintain compliance with applicable standards, all circuits connected

to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to

EN 60825-1.

To avoid potential problems, do not power up the scanner until the communication cable is

secured to the host.

1. Turn off the host system.

2. Find the 19-pin female end of the scanner link cable and the widest key located above

pins L and A. Align this key with the corresponding key on the scanner box’s Mil spec

connector. While pushing in on the connector, rotate the ring clockwise until it locks

into place with a click.

3. Connect the other end of the communication cable to the host device. (If the scanner

will not receive power from a transformer, skip to Step 6.)

4. If the scanner will receive power from an external power source, check the AC input

requirements of the transformer to make sure the voltage matches the AC outlet. (A

socket-outlet shall be installed near the equipment and shall be easily accessible.)

5. Plug the transformer into the AC outlet to supply power to the scanner.

6. Power up the host system.

7. Scan a few items to verify that data is being properly transmitted between the scanner

and the host device.

Figure 1

Attaching the Scanner to the Stand and Work Surface

The scanner can be positioned in a vertical orientation with the Metrologic stand (Part #45478).

To attach the unit to the stand and work surface purchase the following: four 6-32 x ½"

(maximum length) machine screws and two #10 panhead or #8 countersunk wood screws.

1. Lay the scanner face down on a clean cloth to prevent any scratches from occurring on

the output window. Position the scanner so the red and green LEDs are pointed toward

yourself.

2. Lay the stand on the scanner with the angled bracket pointing up and toward yourself.

3. Align the four clearance holes to the four holes in the scanner’s case. Fasten the scanner

to the stand by inserting the four 6-32 x ½" screws into the four holes in the scanner’s

case.

4. Drill two holes into the work surface that correspond with the holes in the

216mm - 95mm (8.5" x 3.75") base of the stand.

5. Use two panhead or countersunk wood screws to attach the scanner and stand to the

work surface. (Refer to Figure 1)

Figure 4

Scanning Bar Codes

The depth of field for the scanner is 203mm to 457mm (8" to 18") from the scanner window. The

symbol must be passed through the scan area in order for the scanner to recognize the bar code.

(Refer to Figure 2)

Appendix A

TECH 8 Laser Bar Code Scanner Specifications

™

Application Industrial Scanner

Light Source Visible Laser Diode 670 ± 5nm

Laser Class CDRH: Class IIa; EN 60825: Class 1

Certifications CE, UL listed for US and Canada

EMC FCC Class A, CISPR Class A

Mechanical

Dimensions 203mm x 216mm x 96mm (8"L x 8.5"W x 3.8"D)

Weight 3.5kg. (7.75 lbs.) without cable

Orientation May be used in any orientation

Mounting Vertical stand

Top Cover NEMA-12 steel case

Cable Length 1.83m (6') cable with mil spec connector

Electrical

Power 9 watts, host system or wall transformer

Input Voltage 11-30 VDC

Operating 450mA typical @ 20V

Current

Standby 210mA typical @ 20V

Current

DC 6061/6113-220V (AC in) 6062/6114-120V (AC in) 6115-240V

Transformers (AC in) output 24/20VDC @ 750mA

Patents Pending

Specifications subject to change without notice.

This manual suits for next models

Table of contents

Metrologic TECH 8 User manual

Popular Barcode Reader manuals by other brands