Metrologic Orbit MS7100 User manual

METROLOGIC INSTRUMENTS, INC.

MS7100 Series Fixed Projection

Laser Scanner

Installation and User’s Guide

MLPN 2408

Printed in USA

October 1998

Locations:

USA Corporate Headquarters Europe

Metrologic Instruments, Inc. Metrologic Instruments GmbH

90 Coles Road Dornierstrasse 2

Blackwood, NJ 08012 82178 Puchheim b.

Customer Service: 1-800-ID-METRO Munich, Germany

Tel: 609-228-8100 Tel: 49-89-89018-0

Fax: 609-228-6673 Fax: 49-89-89019-200

[email protected] [email protected]

www.metrologic.com

ASIA

South America Metrologic Asia (PTE) Ltd.

Metrologic Instruments 31, Khaki Bukit Road 3

Rua Flórida, 1.821-5°Andar-Brooklin #05-08 Techlink

CEP 04571-090, São Paulo-SP, Brasil Singapore 417818

Outside Brazil: Tel: 65-842-7155

Tel: 55-11-5505-6568 Fax: 65-842-7166

Fax: 55-11-5505-1681 [email protected]

[email protected]

In Brazil:

Tel: 55-11-5505-2396

Fax: 55-11-5507-2301

[email protected]

be reproduced, transmitted, or stored in any form or by any means without prior written

consent, except by reviewer, who may quote brief passages in a review, or provided for

in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of their

respective companies.

iii

Table of Contents

Introduction ................................................... 1

Scanner and Accessories ......................................... 2

Quick Start .................................................... 3

Operational Test ............................................... 4

Scanner Installation: Powered by External Power Supply ............... 5

Scanner Installation: Powered by the Host Device ..................... 6

Scanner Installation: to the PC for the Scanner with built-in

PC Keyboard Wedge Interface .................................... 7

Scanner Parts .................................................. 8

Audible Indicators ............................................. 9

Failure Modes ......................................... 10

Visual Indicators .............................................. 11

Labels ....................................................... 12

Depth of Field Specifications .................................... 13

Optimal Depth of Field .................................. 13

Close Depth of Field .................................... 13

Normal Depth of Field .................................. 14

Far Depth of Field ...................................... 14

Minimum Bar Code Element From Scanner Face .................... 15

Optimal Depth of Field .................................. 15

Close Depth of Field .................................... 16

Normal Depth of Field .................................. 17

Far Depth of Field ...................................... 18

Maintenance .................................................. 19

Troubleshooting Guide ...................................... 20-25

Application and Protocols ....................................... 26

Appendix A

Design Specifications 27, 28

Appendix B

Default Settings 29-32

Appendix C

Pin Assignments 33-35

Appendix D

Warranty and Disclaimer 36, 37

Appendix E

Notices 38, 39

Index 40, 41

Introduction

Orbit™ is an aggressive, omnidirectional laser bar code scanner. Light-weight

and rugged, Orbit is small in size, but BIG in performance. Designed for

applications where counter space is limited, Orbit is the ideal presentation

scanner for retail, convenience, liquor and specialty stores. In addition, Orbit’s

unique, contoured shape allows it to be picked-up and used as a hand-held

scanner when scanning large or bulky items.

Engineered with a large, easy-to-find optimal scan area, Orbit increases the

first pass read rate for maximum productivity. The scanning head can be tilted

vertically a full 30 for added flexibility when scanning various sized objects.

These features increase the scanning throughput without increasing the

scanner size.

SCANNER INTERFACE

7100-41 RS-232/Light Pen ready (KBW)

7100-47 Keyboard Wedge ready (KBW)

7100-67 RS-232 ready (OCIA)

7100-9 OCIA ready (OCIA)

7100-11 IBM 46XX/RS-232 ready (IBM)

Orbit offers a great deal of features to the consumer:

‚Fully automatic scanning operation

‚PowerLink compatible

‚Easy programming

‚7 beeper tones

‚Programmable depth of field

‚Data editing

Scanner and Accessories

The following is a list of the parts included in the MS7100 kit.

!MS7100 Hand-Held Laser Scanner - Refer to page 26 for available

communication protocols

!Power Transformer AC in 120V, 220V- 240V Continental

European or 220V- 240V UK. DC in regulates 5.2V@650mA

(MLPN45593/45591/45592)

!MLPN 2408 User’s and Installation Guide

Access MetroSelect Programming Guide MLPN 2407 on the web

http://www.metrologic.com

RS-232, Light Pen, some OCIA and some 46xx scanners:

!PowerLink cable with built in power jack:

Standard - MLPN 54xxx* - 2.1m (7') straight cord, short strain relief

Optional - MLPN 53xxx* - 2.7m (9') coiled cord, long strain relief

*xxx specifies connection to the host

Keyboard Wedge Scanners:

!Keyboard Wedge PowerLink Cable with a 5-pin

DIN female connector on one end and a 6-pin

mini DIN male on the other (MLPN 19763)

!Adapter Cable with a 5-pin DIN male

connector on one end and a 6-pin mini DIN

female connector on the other (MLPN

19716)

Other items may be ordered for the specific protocol being used. To order additional

items, contact the dealer, distributor or call Metrologic’s Customer Service Depart-ment

at 1-800-ID-METRO or 1-800-436-3876.

Quick Start

1.) Plug in the scanner. When the MS7100 is ready to scan,

the red LED will turn on, then the green LED will flash

and the scanner will beep once. (the green LED will

remain on for the duration of the beep).

2.) The scanner is shipped from the factory programmed with

default settings. To configure the MS7100 scanner to meet

the host system’s specific needs, refer to the MetroSelect

Programming Guide (MLPN 2407) for instructions on

how to enter the program mode and to select the appro-

priate bar codes.

Operational Test

Metrologic recommends using the external power supply provided with the

scanner when operating the MS7100. When using power supplied by the host,

the host system should supply a minimum of 250 mA of current @ 5VDC.

Keyboard Wedge Scanners:

1. Connect the 10-pin modular plug of the PowerLink cable into the scanner

jack. Connect the other end of the PowerLink Y-type cable

to the PC. Connect the 5-pin female DIN side of the Y-type cable

into the keyboard connector on the PC and connect the 6-pin male

mini-DIN side into the PC.

2. Check the AC input requirements of the power supply to make sure the

voltage matches the AC outlet. Connect AC power to the transformer.

3. Listen for a single beep that indicates the scanner is ready for use.

(steady red LED and the green LED will flash once)

RS-232, Light Pen, OCIA and 46xx scanners:

1. Connect the 10-pin modular plug of the PowerLink cable into the scanner

jack. Connect the other end of the PowerLink cable (the 9-pin D-type

connector) to the PC.

2. Check the AC input requirements of the power supply to make sure the

voltage matches the AC outlet. Connect AC power to the transformer.

3. Listen for a single beep that indicates the scanner is ready for use.

(steady red LED and the green LED will flash once)

Scanner Installation: Powered by External Power Supply

To maintain compliance with applicable standards, all circuits connected to the

scanner must meet the requirements for SELV (Safety Extra Low Voltage)

according to EN 60950.

1. Turn off the host system.

2. Make the necessary PowerLink cable connections to the scanner and

the host.

3. Connect the external transformer into the power jack on the Power Link

cable.

4. Check the AC input requirements of the power supply to make sure the

voltage matches the AC outlet. (the socket-outlet shall be installed near

the equipment and shall be easily accessible.) Connect AC power to the

transformer.

5. Turn on the host system.

NOTE:

a. When the scanner first receives power, the red LED will turn

on. Then the scanner will beep once and the green LED will

flash simultaneously.

b. Plugging the scanner into the serial port of the PC does not

guarantee that scanned information will appear at the PC. A

software driver and correct configuration setting are also

required for proper communication to occur.

Scanner Installation: Powered by Host Device

The MS7100 scanner interfaces terminate to a 10-pin modular jack. Connect

the 10-pin modular plug of the PowerLink cable into the jack then connect the

other end of the PowerLink cable to the host. Refer to Appendix C page 33 for

pin assignments.

1. Turn off the host system.

2. Make the necessary PowerLink cable connections to the scanner and the

host.

3. Turn on the host system.

NOTE:

a.When the scanner first receives power, the red LED will turn

on. Then the scanner will beep once and the green LED will

flash simultaneously.

b.Plugging the scanner into the serial port of the PC does not

guarantee that scanned information will appear at the PC. A

software driver and correct configuration setting are also

required for proper communication to occur.

This manual suits for next models

Table of contents

Metrologic Orbit MS7100 User manual

Popular Barcode Reader manuals by other brands