Metalicon PMA326 User manual

Installation Instructions

UNPACKING INSTRUCTIONS

ŸCarefully open the carton, remove contents and lay out on cardboard or other

protective surface to avoid damage.

ŸCheck package contents against the Parts List on the next page to assure that all

components were received undamaged. Do not use damaged or defective parts.

ŸCarefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

ŸInstall and operate this device with care. Please read these instructions before

installation, and carefully follow all instructions contained herein. Use proper

safety equipment during installation.

ŸPlease call a qualified installation contractor for help if you don't understand these

directions or have any doubts about the safety of the installation.

ŸDo not use this product for any purpose or in any configuration not explicitly

specified in these instructions. We hereby disclaim all liability for injury or damage

arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

www.metalicon.com

PMA326

POLE ARM FOR 6 MONITORS

Parts List

(1)Pole-a (2)Monitor Arm-b (6)VESA Plate-c

(1)Grommet Plate-e (1)M10 Bolt-f (1)M10 Washer-g (1)Spring Washer-h

(2)Spare Plastic

Cover-t

(1)Allen Key-r (1)Wrench-s(24)M4 Space-q

(24)M4x30 Bolt-p(8)M8x10 Bolt-n(1)Decorative Cover-m

(6)Nut-d

(24)M4x12

Thumb Bolt-o

CAUTION!

WARNING

(2)M10x15 Bolt-k(1) C-clamp-i (1) C-clamp Brace-j (3)C-clamp

Brace Bolt-l

!The monitor mount must be securely attached to a suitable desk top

(minimum 25mm thickness recommended) before fitting the arms

and monitors, failure to do this could lead to an unstable installation

which could result in damage or injury.

Remove the existing grommet to ensure a flat surface before

installing the desk mount.

1. Position the Pole (a) on the mounting surface and secure

using the Grommet Plate (e), M10 Washer (g), Spring Washer

(h) and M10 Bolt (f). Fasten the M10 Bolt using provided

wrench (s).

2. Install the Decorative Cover (m).

Step 1A C-clamp Installation

Step 1B Existing Grommet Hole Installation

1. Install the C-clamp Brace (j) to the pole (a) using 3pcs C-clamp Brace

Bolts (l), see Figure 1.

2. Install the C-clamp (i) to the pole assembly according to the thickness

of the desktop. The thickness can be changed in three positions.

Connect it using 2pcs M10x15 Bolts (k), and tighten using the Allen

Key (r). Tighten the C-clamp to the desktop using the 2pcs eye bolts,

see Figure 2.

3. Install the Decorative Cover (m).

Figure 1 r

Figure 2

eye bolt

Step 1C Drilled Grommet Hole Installation

1. Position the Pole (a) on the mounting surface and mark the

center hole. Remove the pole. Drill a 10mm diameter hole at the

marked position through the mounting surface.

2. Position the Pole (a) on the mounting surface and secure using

the Grommet Plate (e), M10 Washer (g), Spring Washer (h) and M10

Bolt (f). Fasten the M10 Bolt using provided Wrench(s).

3. Install the Decorative Cover (m).

Install arms (b) to the pole(a), please ensure the wire clips on

the arm (b) are on the under side of the arm.

Fasten the M8x10 Bolt (n) with the Allen Key supplied (r).

Step 2 Install Arms to the Pole

wire clip

Step 3 Attach the VESA Plate to the Monitor

For Monitor with Curved or

Recessed Back Use the plastic spacers

(q) and the longer screws (p) to secure

the VESA plate to the monitor.

For Monitor with Flat Back

Use the hand turn screws (o) to secure

the VESA plate directly to the monitor.

Step 4 Slide the Monitor onto the Head of Arms

Install the security nut (d). Make

sure the security nut is installed

before you rotate the monitor.

Slide the monitors onto the heads

of the Monitor Arm (b) as shown in

the above diagram.

Step 6 Adjust the Level of Monitors if necessary.

To adjust the height of Centre Monitor:

Turn the bolt counterclockwise to lower the

centre monitor, turn the bolt clockwise to

raise the centre monitor.

To ad just th e height of S ide M oni tors:

Remove the Nut (d) and turn the bolt counter-

clockwise with supplied Allen key (r) to raise

the monitor. Install the Nut (d) after the

adjustment.

Step 5 Adjust the Tilt Angle and Arms Torque

Remove the plastic cover, adjust

the torque of Arms (b) with

the supplied wrench (s).

Remove the plastic cover, tighten

the nut with the wrench (s) to

adjust the tilt angle tension.

Adjust the tilt angle tension

Other Metalicon Rack & Stand manuals

Metalicon

Metalicon SWD222 User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 