Merlin E840M User manual
CHANGE AN EXISTING PIN
1
? ? ? ?
Press the programmed PIN
that you want to change.
...the light bulb
blinks twice.
2Press and hold the
# button until...
3
+
? ? ? ?
new PIN
Enter the new 4-digit PIN of your choice,
then press the ENTER button.
4To test, press the new PIN,
then the ENTER button.
The garage door opener
will activate.
The light bulb will blink once.
2Enter a 4-digit
personal
number (PIN)
of your choice:
34
1
Locate the
Learn button
on the garage
door opener. ? ? ? ?
Press and hold the ENTER
button until...
...the light bulb blinks
once or 2 clicks are
heard.
Press and
release the
Learn button.
The LED will light.
Within 30 seconds...
PROGRAM INITIAL PIN - using the Learn button
PROGRAM INITIAL PIN - using a multi-function door control* (if this option is installed)
Press the LEARN button again,
Press the LEARN button on the door
control to enter Programming
Mode.
The command
The command
once again.
Enter a 4-digit
personal
number (PIN)
of your choice:
? ? ? ?
4
..the light bulb blinks once
or 2 clicks are heard.
Press and hold the ENTER button until...
For use with Security 2.0 Garage Door Openers. The garage
Number (PIN) and ENTER button are pressed on the Keyless
Entry.
Install the battery and program the Keyless Entry prior to
installation. Make sure the garage door opener has a
working courtesy light because it is a programming indicator.
•
•
•
•
WIRELESS KEYLESS ENTRY • MODEL E840M
*Optional accessory
To test, press the PIN, then press the ENTER button. The garage door opener will activate. To program the Keyless Entry to more than one garage door opener, repeat the steps above using
a new PIN for each additional garage door opener.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
Install Keyless Entry Control within sight of the garage door,out of reach of children
at a minimum height of 1.5m, and away from all moving parts of door.
ALWAYS keep remote controls out of reach of children. NEVER permit children to
operate, or play with remote controls.
Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and
there are no obstructions to door travel.
ALWAYS keep gate or garage door in sight until completey closed. NEVER permit
anyone to cross path of moving gate or door.
+
+
ROLLER DOOR
OPENER
LEARN
BUTTON
LED
INDICATOR
SECTIONAL DOOR
OPENER
LEARN
BUTTON
LED
INDICATOR
...the light bulb blinks 3 times.
1Press any programmed PIN, then press and hold
the
*button until...
+
? ? ? ?
PIN
2
+
? ? ? ?
Temporary PIN
Enter the temporary 4-digit PIN of your
choice, then press the ENTER button.
The light bulb will blink
4 times.
Then press
the button.
3NUMBER OF HOURS
+
NUMBER OF OPENINGS
Press the number
of hours the
temporary PIN
will work (up to 255).
3
OR Then press
the # button.
+
Press the number
of openings the
temporary PIN
will work (up to 255).
1 blink 1 blink
To test, press the temporary
PIN, then press the ENTER
button. The garage door
opener will activate. If the
temporary PIN was set for a
number of openings, the test
will use up one opening.
To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3.
*
OPERATION
The garage door opener activates when the PIN and ENTER
button are pressed. The keypad will blink for 15 seconds, during
that time the ENTER button can be used to stop, start or reverse
the door.
If the wrong number is accidentally pressed, press the correct
PIN then the ENTER button. The Keyless Entry will transmit only
the last four digits that were pressed before the ENTER button.
ONE BUTTON CLOSE: The Keyless Entry has a feature that allows
the door to be closed using the ENTER button instead of a PIN.
NOTE: This feature is not available on external receivers.
To deactivate the one button close feature:
Press and hold the 1 and 9 buttons for 10 seconds.
The keypad will blink four times when the one button close
feature is deactivated.
To activate the one button close feature:
Press and hold the 1 and 9 buttons for 10 seconds.
The keypad will blink twice when the one button close feature
is activated.
PROGRAM A TEMPORARY PIN
A temporary 4-digit PIN can be programmed to allow access
to visitors. Each programmed PIN can program one temporary
PIN. The temporary PIN can be set for a number of hours or a
number of door openings. The temporary PIN cannot be the
same as any previously programmed PIN.
1
1
2
2
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6F22 9V
Keypad Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D621-1
Battery Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D541
REPLACEMENT PARTS
1
INSTALLATION
Select a location to mount the Keyless Entry at a minimum
height of 5 feet (1.5 m) out of the reach of children.
Remove battery cover and battery.
)mm2.3(hcni8/1llirddnaelohgnitnuompotehtkraM
pilot hole.
ot)mm2.3(hcni8/1gniwolla,wercspotehtllatsnI
protrude above the surface. Position the Keyless Entry
over the top screw.
Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot
hole. Install the bottom screw. Do not overtighten to avoid
cracking the plastic housing.
Reinstall battery and replace cover.
2
3
4
5
6
Replace the battery when the keypad
becomes dim or does not light after a
button is pressed.
Dispose of old battery properly.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
BATTERY
9V Battery
WARRANTY
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the original consumer
purchaser of this product that it is free from defect in materials
and/or workmanship for a period of 1 year from the date of
purchase.
114A4383C
Chamberlain service centres:
Australia
Phone toll free 1800 638 234
gomerlin.com.au
New Zealand
Phone toll free 0800 653 667
gomerlin.co.nz
Other Merlin Keypad manuals
