Mercury Security MR62e User manual

www.mercury-security.com

2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755, (562)986-9105 FAX (562) 986-9205

MR62e OSDP Reader Interface

Installation and Specifications

1. General:

The MR62e OSDP reader interface provides a network connected interface to control two physical barriers

using OSDP readers and provides a solution for the OEM integrator for interfacing to OSDP readers and

door hardware. The on-board Ethernet with PoE/PoE+ support enables easy installation. The MR61e

supports up to four OSDP readers configured as paired or alternate readers.

Note: For UL, the Power Sourcing Equipment (PSE) such as a PoE/PoE+ enabled network switch and/or

PoE/PoE+ power injectors must be UL Listed under UL294B.

One serial 2-wire RS-485 communication port is available that can accommodate up to four OSDP

readers. Four Form-C relay outputs may be used for door strike control or alarm signaling. The relay

contacts are rated at 2 A @ 30 Vdc, resistive and are in a dry contact configuration. Six inputs are provided

that may be used for monitoring the door contacts, exit push buttons, and alarm contacts. Input circuits

can be configured as unsupervised or supervised. The MR62e requires PoE, PoE+ or local 12 Vdc for

power. The MR62e may be mounted in a 3-gang switch box; a mounting plate is supplied with the unit or

be mounted in an enclosure; the supplied mounting plate has mounting holes that match the MR50

mounting footprint.

2. MR62e Hardware:

MR62e Layout

TB5

IN1 IN2 IN3 IN4 IN5 IN6

VO GND

VIN

GND

VIN POE

NO NC

2-C

1-C NO NC

4-C

3-C

K1 K2 K3 K4

RVOGND TR- TR+

J3 J4

10519-0000-F, REV-A

7654321

INPUTS

RELAYS

J5: INPUT

POWER

SELECT

12 Vdc IN &

AUX POWER

OUTPUT

2.55 [64.77]

5.4 [137.16]

STATUS

LEDs

2.35 [59.69]

2.75 [69.85]

.2 [5.08]

S1: DIP

SWITCH

J3: TAMPER

SWITCH

TO OSDP

READERS

LINK

(GREEN)

SPEED

(YELLOW)

J4: TIA-485

TERMINATION

JUMPER

Ø.125 [3.18]

6 PLACES

EARTH

GROUND

J1: ETHERNET RJ45

CONNECTOR

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation.

3. MR62e Terminal Blocks and Jumpers/Jacks:

MR-51E CONNECTIONS

TB1-1

IN1

Input 1

TB1-2

IN1

TB1-3

IN2

Input 2

TB1-4

IN2

TB2-1

IN3

Input 3

TB2-2

IN3

TB2-3

IN4

Input 4

TB2-4

IN4

TB3-1

IN5

Input 5

TB3-2

IN5

TB3-3

IN6

Input 6

TB3-4

IN6

TB4-1

Auxiliary Power Output –12 Vdc

TB4-2

GND

Auxiliary Power Output Ground

TB4-3

VIN

Input Power –12 Vdc (from local power supply)

TB4-4

GND

Input Power Ground

TB5-1

Relay K1 –Normally Open Contact

TB5-2

1-C

Relay K1 –Common Contact

TB5-3

Relay K1 –Normally Closed Contact

TB5-4

Relay K2 –Normally Open Contact

TB5-5

2-C

Relay K2 –Common Contact

TB5-6

Relay K2 –Normally Closed Contact

TB6-1

Relay K3 –Normally Open Contact

TB6-2

3-C

Relay K3 –Common Contact

TB6-3

Relay K3 –Normally Closed Contact

TB6-4

Relay K4 –Normally Open Contact

TB6-5

4-C

Relay K4 –Common Contact

TB6-6

Relay K4 –Normally Closed Contact

TB7-1

GND

Reader Power Ground

TB7-2

TR-

2-Wire RS-485 TR- (B) See Note 1 below

TB7-3

TR+

2-Wire RS-485 TR+ (A) See Note 1 below

TB7-4

RVO

12 Vdc Reader Power Output

Note 1: Terms A & B are from the RS-485 standard

Jumpers:

JUMPER

SET AT

DESCRIPTION

N/A

Ethernet Connection with PoE/POE+ support

N/A

Factory Use Only

N/A

Tamper Switch (normally open contact) See section 14.

N/A

RS-485 Termination, install only if the MR62e is at the

end of the communication bus

PoE

MR62e powered from the Ethernet connection

VIN

MR62e powered from an external 12 Vdc power source

connected to TB4-3 (VIN), TB4-4 (GND)

J6 –J13

N/A

Factory Use Only

4. DIP Switches:

The four switches on S1 DIP switch are used to configure the operating mode of the MR62e.

DIP switches are read on power-up except where noted.

Definitions

OFF

Normal operating mode.

OFF

After initialization, enable default User Name (admin) and

Password (password). The switch is read on the fly, no need to

reboot. See IT Security section for additional information

OFF

Use factory default communication parameters.

OFF

Use OEM default communication parameters. Contact system

manufacture for details. See Bulk Erase below.

OFF

Bulk Erase prompt mode at power up. See Bulk Erase section.

All other switch settings are unassigned and reserved for future use. X = don’t care.

Factory Default Communication Parameters:

Network: static IP address: 192.168.0.251

Subnet Mask: 255.255.0.0

Default Gateway: 192.168.0.1

5. Bulk Erase:

The bulk erase function can be used for the following purposes:

Erase all configuration, sets MR62e to OEM setting (sanitize board).

Restore to OEM default parameters.

Bulk Erase Steps: Do not remove power during steps 4-6.

1. Set S1 DIP switches to: 1 & 2 "ON", 3 & 4 "OFF".

2. Apply power to the MR62e.

3. Watch for LEDs 1 & 2 and 3 & 4 to alternately flash at a 0.5 second rate.

4. Within 10 seconds from applying power, change switches 1 or 2 to "OFF". If these switches are not

changed, the MR62e will power up using the OEM default communication parameters.

5. LEDs 1 and 2 alternately flash at a 0.5 second rate while the memory is being erased.

6. Once the memory is eased, LED 1 will be on for about 3 seconds, then the MR62e will reboot.

6. Input Power:

The MR62e is powered by one of two ways (jumper selected, J5):

Power is supplied via the Ethernet connection using PoE or PoE+.

Local 12 Vdc power supply, TB4-3 (VIN), TB4-4 (GND).

7. Communication Wiring:

Communication between the EP controller and the MR62e is Ethernet (10Base T/100Base-TX).

It is not recommended to connect the MR62e to a public intranet.

8. OSDP Reader Wiring:

TB7 has connections for the 2-wire RS-485 OSDP communication bus and 12 Vdc to power the OSDP

readers. Up to four OSDP readers are supported on the MR62e. This 12 Vdc output is limited to .5 A.

maximum. The OSDP reader wiring diagram below shows the use of a 2-pair cable for data and power.

If this cable cannot support the voltage/current requirements, a 1-pair cable of sufficient gauge must be

used for power. See specification section.

The RS-485 termination jumper, J4, is only installed if the MR62e is at one end of the communication

bus. Only devices at each end of the communication bus are terminated, never install termination to

more than two devices on the communication bus.

When powering any remote device(s) by the MR62e, care must be taken not to exceed the maximum

current available. Cable gauge must also be evaluated. See specifications section for details.

Typical OSDP Reader Wiring

9. Input Circuit Wiring:

Typically, these inputs are used to monitor door position, request to exit, or alarm contacts. Input circuits

can be configured as unsupervised or supervised. When unsupervised, reporting consists of only the

open or closed states.

When configured as supervised, the input circuit will report not only open and closed, but also open circuit,

shorted, grounded*, and foreign voltage*. A supervised input circuit requires two resistors be added to the

circuit to facilitate proper reporting. The standard supervised circuit requires 1K Ohm, 1% resistors and

should be located as close to the sensor as possible. Custom end of line (EOL) resistances may be

configured via the host software.

*Grounded and foreign voltage states are not a requirement of UL 294 and therefore not verified by UL.

The input circuit wiring configurations shown are supported but may not be typical:

TR+ (A)

RVO

TR- (B)

GND

TR- (B)

GND

TB7

12 V

J3 J4

J4: INSTALL ONLY IF MR62e IS AT THE

END OF THE COMMUNICATION BUS

TR+ (A)

GND

TR- (B)

12 V

TR+ (A)

GND

TR- (B)

12 V

TR+ (A)

GND

TR- (B)

12 V

SHIELD: CONNECT TO

EARTH GROUND,

ONE END ONLY!

1K,1%

Standard Supervised Circuit,

Normally Closed Contact

Standard Supervised Circuit,

Normally Open Contact

Unsupervised Circuit,

Normally Open Contact

Unsupervised Circuit,

Normally Closed Contact

TB2

IN4

IN2

IN3

IN1

TB1

}

10. Relay Circuit Wiring:

Four Form-C contact relays are provided for controlling door lock mechanisms or alarm signaling. The

relay contacts are rated at 2 A @ 30 Vdc, resistive and are in a dry contact configuration. When you are

controlling the delivery of power to the door strike, the Normally Open and Common poles are used. When

momentarily removing power to unlock the door, as with a mag lock, the Normally Closed and Common

poles are used. Check with local building codes for proper egress door installation.

Door lock mechanisms can generate feedback to the relay circuit that can cause damage and premature

failure of the relay. For this reason, a diode must be used to protect the relay. Wire should be of sufficient

gauge to avoid voltage loss.

It is possible for the MR62e to provide power for a 12 Vdc door strike providing the maximum current is

not exceeded, see specification section.

11. Status LEDs:

At power up, LED 1 turns ON then LEDs 2 through 7 are turned ON then OFF in sequence.

The following table describes the LED’s in the Normal Running mode:

LED

DESCRIPTION

On-line, encryption disabled = 0.8 second ON, 0.2 second OFF

On-line, encryption enabled = 0.1 second ON, 0.1 second OFF, 0.1 second ON, 0.1

second OFF0.1 second ON, 0.1 second OFF0.1 second ON, 0.3 second OFF

Off-line: 0.2 second ON, 0.8 second OFF

Waiting for application firmware to be downloaded: .1 sec ON, .1 sec OFF

Input IN1 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN2 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN3 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN4 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN5 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN6 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

J1-YELLOW

Ethernet speed: OFF = 10 Mb/S, ON = 100 Mb/S

J1-GREEN

OFF = No Link, ON = Good Link, Flashing = Ethernet Activity

Note 2: If this input is defined, every three seconds the LED is pulsed to its opposite state for 0.1

second, otherwise, the LED is off.

12. IT Security:

When installing the MR62e, it is important to ensure that it is done in a secure manner.

Upon installation, the user accounts to the web configuration page should be created with secure

passwords, and that all DIP switches are in the off position for the normal operating mode. The MR62e

is shipped from the factory with a default login account, which is enabled when DIP 1 is moved from OFF

to ON. The default login user name and password will be available for five minutes once enabled.

Therefore, it is important that at least one user account is defined, and the DIP switches are set to OFF

before the MR62e is commissioned. It is also highly recommended not to configure the MR62e with an

IP address that is accessible from the public Internet.

Diode Selection:

Diode current rating: 1x strike count

Diode breakdown voltage: 4x strike voltage

For 12 Vdc or 24 Vdc strike, diode 1N4002

(100V/1A) typical.

TB5

To further enhance network security, options are available to disable Zeroconf discovery, as well as the

web configuration module itself.

13. Specifications:

The MR62e is for use in low voltage, Class 2 circuits only.

Power Input: PoE (12.95 W), compliant to IEEE 802.3af

PoE+ (25 W), compliant to IEEE 802.3at

12 Vdc 10 %, 1.7 A maximum

For UL, the Power Sourcing Equipment (PSE) such as a PoE/PoE+ enabled network switch and/or

PoE/PoE+ power injectors must be UL Listed under UL294B. Wiring for the 12V input shall not extend

more than 30m from the product.

Power Output: PoE: VO (TB4-1) and RVO (TB7-4), combined: 12 Vdc @ .66 A maximum

PoE+ or 12 Vdc: VO (TB4-1) 12 Vdc @ 1 A maximum, RVO, (TB7-4) 12 Vdc

@ .5 A maximum

Output: Four relays, Form-C contacts rated at 2 A @ 30 Vdc

Inputs: Six unsupervised/supervised, End of Line resistors, 1k/1k ohm, 1%, ¼ watt

standard

Reader Interface:

Power: 12 Vdc @ .5 A maximum (RVO, TB7-4)

Communication: 2-Wire RS-485, OSDP protocol, four devices maximum

Cable Requirements:

Communication: Ethernet, Category 5, minimum

External Input Power: 1 twisted pair, 18 AWG (if required)

Alarm Inputs: 1 twisted pair per input, 30 ohm maximum

Relay Outputs: As required for the load

Reader Data RS-485/power: 2 twisted pair with shield, 24 AWG, 120 ohm impedance

and Power* 4000 foot (1220 m) maximum.

RS-485: 1 twisted pair with shield, 24 AWG, 120 ohm impedance, 4000 foot

(1220 m) maximum

and

power: 1 pair 18 AWG*

* Type of cable(s) and gauge determined by length and voltage/current

requirements. Local power source may be required

Environment:

Temperature: -55 to +85 C, storage

0 to +70 C, operating

Humidity: 5 to 95 % RHNC

Mechanical:

Dimension: 5.5 in. (140 mm) W x 2.75 in. (70 mm) L x 0.96 in. (24 mm) H without bracket

5.5 in. (140 mm) W x 3.63 in. (92 mm) L x 1.33 in. (34 mm) H with bracket

Weight: 4 oz. (112 g) without bracket

5 oz. (142 g) with bracket

UL294, 6th edition Performance Levels:

Feature

Level

Standby Power

Endurance

Line Security

Destructive Attack

14. Additional Mounting Information:

Sources for the optional items shown below:

3-gang stainless steel blank cover. Available from:

Leviton part number 84033-40

Graybar part number 88158404

Magnetic switch set: G.R.I. part number: 505

Side View:

FIELD WIRING

MR51e WITH INCLUDED

MOUNTING PLATE

TO ETHERNET

NETWORK

OPTIONAL 3-GANG

JUNCTION BOX

OPTIONAL BLANK

COVER W/SCREWS

OPTIONAL MAGNETIC

TAMPER SWITCH

Mounting Plate Dimensions:

Warranty

Mercury Security warrants the product is free from defects in material and workmanship under normal use

and service with proper maintenance for one year from the date of factory shipment. Mercury Security

assumes no responsibility for products damaged by improper handling or installation. This warranty is

limited to the repair or replacement of the defective unit.

There are no expressed warranties other than set forth herein. Mercury Security does not make, nor

intends, nor does it authorize any agent or representative to make any other warranties, or implied

warranties, and expressly excludes and disclaims all implied warranties of merchantability or fitness for a

particular purpose.

All returns must be accompanied by a Return Material Authorization (RMA) number obtained from customer

service, and prepaid postage and insurance.

Liability

The Interface should only be used to control exits from areas where an alternative method for exit is

available. This product is not intended for, nor is rated for operation in life-critical control applications.

Mercury Security is not liable under any circumstances for loss or damage caused by or partially caused

by the misapplication or malfunction of the product. Mercury Security’s liability does not extend beyond the

purchase price of the product.

3.85 [97.8]

2.35 [59.7]

5.50 [139.7]

3.63 [92.1]

3.30 [83.8]

3.63 [92.1]

Ø0.16 [Ø4.0]

MR50 MGT HOLES

4PL

Ø0.16 [Ø4.0]

3-GANG MGT HOLES

4PL

Other Mercury Security Recording Equipment manuals

Mercury Security

Mercury Security MR51e User manual

Popular Recording Equipment manuals by other brands

KV2 Audio

KV2 Audio 500 Series user guide

Robotics Technologies

Robotics Technologies microBus-Cam II installation manual

Seca

Seca 460 quick start guide

Cognex

Cognex MVS-8000 Series Hardware manual

Mect

Mect MPNC006 Series user manual

Bad Caf

Bad Caf THE LEASH operating manual

Strymon

Strymon NIGHTSKY user manual

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U user manual

Tews Technologies

Tews Technologies TPMC465 user manual

Honeywell

Honeywell Excel 50 user guide

SeaLevel

SeaLevel COMM+8.LPCI user manual

Arturia

Arturia AUDIOFUSE STUDIO user manual

Rukra

Rukra RK-1240 quick start guide

Samson

Samson SCOM owner's manual

Dynacord

Dynacord DPS260 owner's manual

Nice

Nice Core user manual

Pyle Pro

Pyle Pro PSS8 manual

RF-System

RF-System TinyGate Assembly and user's manual