Mechan ISIS User manual

This information is designed to help suitably qualified

personnel install and operate Mechan Safety Switch

equipment. Before using this product, read this guide thoroughly along with

any relevant European and/or National standards e.g. Machinery Directive

89/392/EEC and it’s amendments, Provision and Use of Work Equipment

Regulations.

Further information can be obtained from Mechan Controls PLC

***** KEEP THIS GUIDE FOR FUTURE REFERENCE *****

CAUTION

DESCRIPTION

The ISIS safety system is a tamper resistant non-contact

safety switch system, suitable for use in most types of

machine guarding applications where guard locking is not

required. The system comprises of a control unit and 1 or

more safety switches and actuators. The ISIS non-contact

safety switches are easy to install, tolerant to misalignment

and suitable for use in harsh or wet environments.

ISIS-4 - Control Unit

The ISIS-4 is a combined Safety Switch and E-Stop control

unit. Along with the ability to monitor up to four ISIS safety

switches it can also monitor the normally closed contacts of

emergency stop buttons or mechanical safety switches in

dual channel control circuits.

The ISIS-4 has 2 normally open safety contact outputs and 1

normally closed auxiliary output, an external re-set/proving

circuit and LED indication for ‘Power’, ‘Run’ and the status of

each activated gate switch.

ISIS-2 - Control Unit

The ISIS-2 control unit is a 24V ac/dc system that can

monitor up to 2 ISIS safety switches.

The ISIS-2 has 2 normally open safety contact outputs and 1

normally closed auxiliary output, an external re-set/proving

circuit and LED indication for ‘Power’, ‘Run’ and the status of

each activated gate switch.

ISIS-E - Extender Module

The ISIS-E Extender module is a 24V ac/dc unit that can be

added to either the ISIS-4 or ISIS-2 to monitor an additional

5 ISIS safety switches. Connection to the main control unit is

by a simple 2-wire bus connection. The status of each guard

switch is shown by the YELLOW LED’s. Additional ISIS-E

extender modules can be added to monitor larger systems.

ISIS-03M / ISIS-SS-03M - Safety Switches

The ISIS safety switches are non-contact, tamper resistant

safety switches. Resin encapsulated into an ABS or

Stainless Steel case providing environmental protection to

IP67, the switches can withstand most conditions including:

water, dust and high pressure hose cleaning.

The 2-wire connection to each safety switch is

monitored by the control unit, detecting both open and

short circuit faults immediately and returning the control

unit to the off state even if the gate is not operated.

APPLICATIONS

Interlocked guards where door locking is not required.

Food and Beverage packing/filling systems; Diary,

Pharmaceutical, Paper Industry, Can Forming and Filling,

(Aluminum, Steel, Plastic), Semiconductor Manufacture/

Assembly. Concrete Block Manufacture.

ISIS SAFETY SYSTEM

Installation guide

APPROVALS

CE Complies with the relevant sections of the CE

marking directive.

UL Tested by the Underwriters Laboratories, USA,

to comply with the relevant USA and Canadian

requirements. UL 508 Industrial Control

TUV CAT 3 SIL 3 PLe

EUROPEAN DIRECTIVES

Machinery Directive 2006/42/EC

Low Voltage Directive 2006/95/EC

Electromagnetic Compatibility Directive 2004/108/EC

EUROPEAN STANDARDS

EN ISO

13849-1 Safety of Machinery - Safety related parts of

control systems

EN ISO

62061 Safety of Machinery - Functional safety of safety

related electrical, and electronic and

programmable electronic control systems

EN 60204 Safety of Machinery - Electrical equipment of

machines.

EN 1088 Interlocking devices associated with guards.

60947-5-3 Safety of Machinery - Specification for low

voltage switchgear and control gear.

CERTIFICATE OF CONFORMITY

A certificate of conformity can be supplied covering Mechan

non-contact safety switch equipment.

Call our technical help-line on +44 (0)1695 722264

EN 60947-

5-1 Low voltage switchgear and control gear.

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

ISIS-4 TERMINAL INFORMATION

TERMINAL

NUMBER DESCRIPTION

A1 ; A2 Power Supply

S13 ; S14 E-Stop / Mechanical Safety

Input—Channel 1

S23 ; S24 E-Stop / Mechanical Safety

Input—Channel 2

X1 ; X2 External Proving / Reset

BL ; DR - Gate

inputs 1 to 4 Guard Switch Inputs

13 ; 14 N/O Safety Contact 1

23 ; 24 N/O Safety Contact 2

31 ; 32 N/C Auxiliary Contact

BL DR

POWER - RED

GATE 1 - YELLOW

GATE 2 - YELLOW

RUN - GREEN

GUARD

SELECTOR

SWITCH

RESET

SELECTOR

SWITCH

GATE 1 INPUT

GATE 2 INPUT

ISIS-2 TERMINAL INFORMATION

TERMINAL

NUMBER DESCRIPTION

A1 ; A2 Power Supply

X1 ; X2 External Proving / Reset

BL ; DR - Gate

inputs 1 & 2 Guard Switch Inputs

13 ; 14 N/O Safety Contact 1

23 ; 24 N/O Safety Contact 2

31 ; 32 N/C Auxiliary Contact

BL BL

POWER - RED

RESET

SELECTION

SWITCH

GATE STATUS

INDICATORS

(YELLOW)

GS5

GS4

GS3

GS2

BUS

GATE 2 INPUT

GATE 5 INPUT

GATE 1 INPUT

GATE 4 INPUT

GATE 3 INPUT

ISIS-E TERMINAL INFORMATION

TERMINAL

NUMBER DESCRIPTION

A1 ; A2 Power Supply

BL ; DR - Gate

inputs 1 to 5 Guard Switch Inputs

BL ; DR - BUS Bus connection to main

control unit

SYSTEM INSTALLATION

This installation guide is to help trained personnel to install the ISIS non-

contact safety switch system.

The ISIS system is suitable for most types of machine guarding

applications where guard locking is not required. The safety switches can

be fitted to sliding, hinged or removable machine guards.

Comprising of a Safety Control Unit ( ISIS-4 / ISIS-2 / ISIS-E) and one or

more Safety Switch and Actuators, systems can easily be assembled to

monitor 30+ machine guards whilst retaining the high control category

performance required in many applications. (CAT 3 according to EN954-1)

To assemble the system, mount the control unit in a suitably IP rated

control panel (Min IP54) and fix the safety switches to the gates as shown.

Connect the safety switches to the control unit. Using the appropriate

selection table set the required active gate inputs and reset options.

IMPORTANT :

PRODUCT IDENTIFICATION AND TERMINAL LAYOUT

HINGED DOORS

ISIS

Control

Unit

LIFT OFF DOORS

SLIDING DOORS

234

S13

S23

X1 BL BL DRDR 31 13 23

S14

S24

X2 BL BL DRDR 32 14 24

GATE 3 GATE 4

RUN - GREEN

POWER - RED

GUARD

STATUS

YELLOW

GUARD SELECT

GREEN

GUARD

SELECTOR

SWITCH

ATE 1 INPUT

ATE 2 INPUT

GATE 3 INPUT GATE 4 INPUT

GATE 1 GATE 2

RESET SELECTOR

SWITCH

Guard

Selector

Switch

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

FITTING THE CONTROL UNIT

The ISIS control units are designed to fit standard 35mm symmetric DIN rail.

TO FIT : Hook the unit onto the DIN rail (1) and gently push into place (2).

The catch should hold the unit securely in place.

TO REMOVE: Place the tip of a small screwdriver into the white catch at the

bottom of the box (1) and gently lever out. This releases the retaining clip

and allows the unit to be tilted (2) and removed (3).

OFFON

GUARD SELECTOR & RESET SWITCHES

The central part of the ISIS control unit lid (1) is removable. Using a small screwdriver in the recess

(2) gently prise the lid upwards. This allows access to the Automatic/Manual monitored Reset

switch and the Guard Selector Switch.

Using the table next to the relevant control unit overleaf, set the ISIS control unit to the required

number of guard switch inputs and type of reset required.

IMPORTANT:

The number of inputs (safety switches) must match the gate selector setting.

Any incorrect setting will stop the system from operating correctly.

APPLICATION NOTES

FITTING THE SAFETY SWITCHES

The ISIS safety switch sensors have 2 pre-drilled fixing holes and are

supplied with M4 x 20mm TORX Tamper Proof fixing screws. (see page 7

for dimension details)

The gate switches can approach each other from any angle (A), but must

end up with the arrows on the printed face pointing towards each other.

Mount the fixed part of the safety switch to the machine frame and the

actuator on to the opening edge of the door (B).

For the best results, mount the sensors with a gap of approximately 1mm.

when the guard is closed. This gives a high level of lateral tolerance to

allow for ‘gate sag’ and freedom from nuisance tripping due to machine /

guard vibration.

WRONG!

Min. 50m

1) Always try to mount the safety switch on non-ferrous material.

Ferrous materials will reduce the switching distance.

2) Leave a minimum 50mm gap between actuators. (A)

3) Avoid mounting the safety switch on the hinged side of the

door, as this may allow the door to be opened too far before the

switch de-activates. (B)

CONNECTING SWITCHES TO THE CONTROL UNIT

The ISIS safety switches are supplied with 3 or 5 metres of cable encapsulated into the

fixed switch. This ensures a completely water-tight connection at the switch.

Cables can be extended using the same type of screened cable.

Run the cable back to the control unit through cable protection (if required) and

terminate into the appropriate control unit input channel.

Follow the colour coding of the wires to the labels on the control unit input terminals.

i.e. BLUE wire to BL and DRAIN wire to DR.

NOTE : High Temp Switches use Blue wire to BL & Brown wire to DR

Longer cable lengths are available to order.

MAX. 100

ISIS

CONTRO

UNIT

ISIS

SAFETY

SWITCH

IMPORTANT: Use the GATE inputs in sequence. Examples:

One Guard System—Use input 1 on the ISIS-2 ( Or input 1 on the ISIS-4 if E-Stop function required);

Three Guard System—Use inputs 1, 2 & 3 on the ISIS-4;

Seven Guard System—Use inputs 1,2 & 3 for Guard Switches on the ISIS-4 and Input 4 to connect to the ISIS-E Extender

module Bus connection. Then use inputs 1,2,3 & 4 on the ISIS-E

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

ISIS-4 CONNECTIONS

POWER SUPPLY : 24Vac/dc ; 110Vac or 230Vac

POWER SUPPLY FUSING : Internal resetable fuse with 2

second delay after fault removal.

INDICATION : RED - Power On; GREEN - Run.

YELLOW - Guard Status indicators.

GREEN - Guard Selected status.

GUARD SELECTION : See ISIS-4 switch table.

RE-SET & MONITORING : The X1, X2 circuit is for reset

buttons and/or monitoring external contactors.

Set to Manual Reset (see table) a normally open

momentary push button should be placed across X1 & X2.

The push button must be pressed and released as it is

monitored for short circuit faults.

Set to Automatic Reset, link X1, X2 and the system will

reset when all active guards are closed.

To Monitor External Contactors (K1 & K2) place a

normally closed contact off each contactor in series with

X1 & X2 (with or without a reset button as required) If

either K1 or K2 welds during operation, the other contactor

will operate correctly and on the next demand on the

safety system the X1 X2 circuit will prevent a restart. Use

PGC relays for K1 & K2 if monitoring required.

CONTROL CONTACTS : Two sets of positively guided N/O safety contacts on terminals, 13,14; and 23,24 (rating 4 Amps).

One auxiliary N/C contact, (31-32). External fusing is recommended.

EMERGENCY STOP MONITORING : Dual channel emergency stop buttons and/or mechanical safety switches can be

monitored using the S13/S14 & S23/S24 circuits. If this feature is not used link terminals S13 to S14 and S23 to S24.

OPERATION : When power is applied to the control module, the RED ‘Power Led’ will illuminate. The GREEN ‘De-select’

indicators will show how many guard switch inputs are activated. NOTE: The number of inputs selected must match the

number of guard switches, more or less and the control unit will not operate. The YELLOW ‘Guard status’ indicators will be

illuminated if the guard is closed or be permanently on if the guard is de-selected.

If all the monitored machine guards are closed, the EMERGENCY STOP buttons (when used) are re-set and the RE-SET

button is pressed and released (Manual Re-set Option), the control relays will energize closing the normally open safety

contacts on terminals 13,14 / 23,24 and the normally closed auxiliary contact 31 & 32 will open. The GREEN Run LED will

illuminate. If set to automatic re-set ( I.e. link in X1 & X2) the control relays will energize when all active guards are closed and

the emergency stop button(s) are re-set. Faults on the safety switch cables, either open or short circuit will be detected

immediately causing the control relays to de-energize.

Single faults on the Emergency stop contacts will be detected upon the next demand and will prevent a restart.

ISIS-4 RESET AND MONITORING

SWITCH

Reset

Switch

Position Operation

Automatic Reset

Link required between

terminal X1 & X2. ISIS-4 will

reset when all active guards

are closed.

Manual / Monitored Reset

Requires a reset button in

the X1—X2 connection. The

system will reset when all

ISIS-4 GUARD SELECTION SWITCH & INDICATION

Guard

Indication

(Yellow)

De-select

Indicator

(Green)

Channel

Selector

Switch Operation

1 Gate Operation—Yellow LED No. 1 will

illuminate when gate switch 1 is closed.

All other Yellow gate indicators will remain

illuminated. No green LED’s illuminated.

2 Gate Operation—Yellow LED’s 1 & 2 will

illuminate when corresponding gate switch is

closed. All other Yellow gate indicators will remain

illuminated. Top green LED illuminated.

3 Gate Operation—Yellow LED’s 1,2 &3 will

illuminate when corresponding gate switch is

closed. All other Yellow gate indicators will remain

illuminated. Top two green LED’s illuminated

4 Gate Operation—Yellow LED’s 1,2,3 & 4 will

RUN

POWER

GATE 4GATE 3

GATE 4

GATE 3

GATE 2

DE-SELECT

S13 S23

X1 BL DR BL DR 31 13

S14 S24

X2 BL DR BL DR 32 14 24

GATE 2GATE 1

GS3GS4

GS1GS2

K1 K2

MECHANICAL

SAFETY

SWITCHES

EMERGENCY

STOP

MANUAL

RE-SET

L (+ve)

N (-ve)

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

ISIS-2 CONNECTIONS

POWER SUPPLY :

24Vac/dc

POWER SUPPLY FUSING :

Internal resetable fuse with 2 second delay after fault removal.

INDICATION :

RED - Power On.

GREEN - Run.

YELLOW - Guard Status.

GUARD SELECTION :

See ISIS-2 Guard selection chart.

RE-SET & MONITORING :

The X1, X2 circuit is for reset buttons and/or monitoring external contactors.

Set to Manual Reset (see table) a normally open momentary push button should be

placed across X1 & X2. The push button must be pressed and released as it is

monitored for short circuit faults.

Set to Automatic Reset, link X1, X2 and the system will reset when all active guards

are closed.

To Monitor External Contactors (K1 & K2) place a normally closed contact off each

contactor in series with X1 & X2 (with or without a reset button as required) If either

K1 or K2 welds during operation, the other contactor will operate correctly and on the

next demand on the safety system the X1 X2 circuit will prevent a restart. Use PGC relays for K1 & K2 if monitoring required.

CONTROL CONTACTS :

Two sets of positively guided N/O safety contacts on terminals, 13,14; and 23,24 (rating 4 Amps). One auxiliary N/C contact,

(31-32). External fusing is recommended.

OPERATION :

When power is applied to the control module, the RED ‘Power Led’ will illuminate. The number of inputs selected must match

the number of guard switches, more or less and the control unit will not operate. The YELLOW ‘Guard status’ indicators will be

illuminated if the guard is closed or be permanently on if the guard is de-selected.

If all the monitored machine guards are closed and the RE-SET button is pressed and released (Manual Re-set Option), the

control relays will energize closing the normally open safety contacts on terminals 13,14 / 23,24 and the normally closed

auxiliary contact 31 & 32 will open. The GREEN Run LED will illuminate.

If set to automatic re-set ( I.e. link in X1 & X2) the control relays will energize when all active guards are closed and the

emergency stop button(s) are re-set. Faults on the safety switch cables, either open or short circuit will be detected

immediately causing the control relays to de-energize.

ISIS-2 RESET AND MONITORING

SWITCH

Reset

Switch

Position Operation

Automatic Reset

Link required between

terminal X1 & X2. ISIS-2 will

reset when all active guards

are closed.

Manual / Monitored Reset

Requires a reset button in

the X1—X2 connection. The

system will reset when all

ISIS-2 GUARD SELECTOR SWITCH

& INDICATION

Gate

Indication

Yellow

Gate

Selector

Switch Operation

1 Gate Operation—Yellow

LED No. 1 will illuminate

when gate switch 1 is

closed. Yellow LED No. 2

will remain illuminated.

2 Gate Operation—Yellow

LED’s 1 & 2 will illuminate

when corresponding gate

IMPORTANT

On all ISIS safety control

units use the guard inputs

in sequence.

Always set the control unit

guard selector switch to

match the number of safety

switches fitted

Any other setting may

cause improper operation.

GATE 2

A1 X1 BLDR31 13 23

A2 X2 BLDR32 14 24

GATE 1

GS2

GS1

K1 K2

24V

(+ve)

(-ve)

POWER

IND 1

IND 2

RUN

MANUAL

RE-SET

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

ISIS-E

CONNECTIONS

POWER SUPPLY :

24Vac/dc

POWER SUPPLY FUSING :

Internal resetable fuse with 2 second delay after fault

removal.

INDICATION :

RED - Power On.

YELLOW - guard status indicators.

GUARD SELECTION :

See ISIS-E Guard selection chart.

CONNECTION TO MAIN CONTROL UNIT:

The ISIS-E can be connected to any active guard switch

input on an ISIS-2 or ISIS-4.

Connect the 2-wire BUS ( BL DR ) terminals on the ISIS-E

module to any activated guard input on the main control

module. (Max distance 100 metres)

For larger systems further ISIS-E extender modules can

be connected to active guard switch inputs on an ISIS-E

extender module.

OPERATION :

When power is applied to the control module, the RED

‘Power Led’ will illuminate. The number of inputs selected must match the number of guard switches, more or less and the

control unit will not operate. The YELLOW ‘Guard status’ indicators will be illuminated if the guard is closed or be permanently

on if the guard is de-selected.

If all the monitored machine guards are closed and the RE-SET button is pressed and released on the main control unit, the

control relays will energize and the normally open safety contacts on terminals 13,14 / 23,24 (main control unit) will close. The

normally closed auxiliary contact 31 & 32 (main control unit) will open. If set to automatic re-set ( i.e. link in X1 & X2) the

control relays will energize when all active guards are closed and the emergency stop button(s) (if connected) are re-set.

Faults on the safety switch cables, either open or short circuit will be detected immediately causing the control relays to de-

energize.

A1 BLDR

GATE 1

GS1

24 V

+ve

0 V

-ve

BLDR BLDR

GATE 2 GATE 3

GS2 GS3

A2 BLDR

GATE 4

GS4

BLDR BLDR

GATE 5 BUS

GS5

IND 1

IND 2

IND 3

IND 4

IND 5

2-WIRE BUS CONNECTION

POWER

-E Extender Module

(24VDC) I

ontrol Unit

(24VDC)

BL DRA2

ISIS-4 or ISIS-2

CONTROL UNIT

Connect the ISIS-E

Bus connection to

an active gate input.

ISIS-E GUARD SELECTOR SWITCH & INDICATION

Guard

Indication

(Yellow)

Channel

Selector

Switch Operation

1 Gate Operation—Yellow LED

No. 1 will illuminate when gate

switch 1 is closed. All others gate

indicators remain illuminated.

2 Gate Operation—Yellow LED’s

1&2 will illuminate when

corresponding gate switch is

closed. IND 3, 4 & 5 remain

illuminated.

3 Gate Operation—Yellow LED’s

1,2 &3 will illuminate

corresponding gate switch is

closed. IND 4 & 5 remain

illuminated.

4 Gate Operation—Yellow LED’s

1,2,3 & 4 will illuminate when

corresponding gate switch is

closed. IND 5 remains illuminated.

5 Gate Operation—Yellow LED’s

1,2,3,4 & 5 will illuminate when

corresponding gate switch is

12 GATE SYSTEM

with E-STOP Control

ISIS-4

Set to 4 gate operation

1st ISIS-E

Set to 5 gate operation

2nd ISIS-E

Set to 5 gate operation

10 GATE SYSTEM

ISIS-2

Set to 2 gate operation

1st ISIS-E

Set to 5 gate operation

6 GATE SYSTEM with

E-STOP Control

ISIS-4

Set to 4 gate operation

ISIS-E

Set to 3 gate operation

SYSTEM EXAMPLES WITH EXTENDER MODULES

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

Dimensions ISIS-4

(mm / inches)

W 75 / 2.95

H 74 / 2.91

D 119 / 4.68

Information only

Dimensions

ISIS-2 & ISIS-E

(mm / inches)

W 22.5 / 0.88

H 84 / 3.3

D 119 / 4.68

Information only

Dimensions

ISIS-03M

(mm / inches) ISIS-SS-03M

(mm / inches)

H 28 / 1.1 29 / 1.14

W 52 / 2.04 53 / 2.08

D 14 / 0.55 13.5 / 0.53

D1 3 / 0.11 3 / 0.11

A 22 / 0.86 22 / 0.86

B1 4.2 / 0.16 dia. 4.2 / 0.16 dia.

B2 8.1 / 0.32 dia. 8.1 / 0.32 dia

C 6.4 / 0.25 6.4 / 0.25

Information only

DIMENSIONS

ISIS-4 (all voltages)

ISIS-2 & ISIS-E

ISIS SAFETY SWITCHES ABS / STAINLESS STEEL

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

TECHNICAL INFORMATION

SPECIFICATIONS ISIS CONTROL UNITS ISIS SAFETY SWITCHES

ISIS-4 ISIS-2 ISIS-E ISIS-03M / 05M ISIS-SS-03M

Supply nominal voltage 24Vac/dc

110 or 230Vac 24Vac/dc 24Vac/dc - -

Nominal power consumption 6VA 3VA 3VA - -

Safety contacts 2 x N/O - - -

Auxiliary contact 1 x N/C - - -

Output contact rating (max) 4A/230Vac; 2A/24Vdc(Res.)@Cos=1 - - -

Output contact rating (min) 10V/10mA - - -

Output contact fuse rating AC=5A; DC=2.5A; Quick blow - - -

Drop out time Deactivation by sensor 13ms - -

Nominal voltage across BL/DR sensor ON: 4V; OFF 0 to 10Vdc

Internal fuse 500mA Resettable - -

Internal fuse recovery time >2 Seconds - -

Internal switches Active gate selector; Manual or

Monitored reset selection Active gate

selector - -

Max conductor size 1 x 2.5mm stranded with sleeves, 1 x 4mm solid - -

Installation group (Control unit) C in accordance with VDE0110 - -

Contamination level

Vibration resistance Amplitude 2mm, frequency 10 to 55 Hz -

Enclosure protection Housing IP40, Terminals IP20 IP67

Switching distance - - - 5-7mm ON; 8-12mm OFF

Minimum gap 1mm

Cable length 3 or 5 metres (Max 100 metres)

Operating temperature -10C to +55C (85% Humidity max) -10C to +55C

-10C to + 125C (SS High Temp.)

Storage temperature -20C to +60C -20C to +60C

Housing material Polycarbonate Red ABS Red 316 Stainless

Steel

Mounting / Fixing 35mm Symmetric DIN Rail 22mm Centres;

M4 security screws supplied

Tightening torque 1.0NM

Weight (AC/DC) (3m/5m) 575g max. 183g 135g 207g max 265g

Dimensions See page 7

III

Safety Related Data

PL In accordance with EN ISO 13949-1 PL e, CAT 3

SIL In accordance with EN ISO 62061 SIL 3

PFHd in accordance with EN ISO 62061 3.37 x 10-8

PFH 5.63 x 10-8

B10d 2,000,000

MTTFd High > 100 Years ( Based on usage rate of 360 days/year, 24 hours/day, 10 operations/hour

TM (Mission Time ) 20 Years

DC 99%

SFF 99.4%

Document Number : 370-400v13

UK Office

5 Caulside Drive, Antrim, BT41 2DU

United Kingdom

TEL: +44 (0) 28 9448 1800

www.pneutrol.com/industrialspares

European Office

Unit 6, Saint Anthony’s Business Park, Ballymount Road, D22 VW95

Ireland

TEL: +353 (0) 1 4373653

www.pneutrol.com/industrialspares

__________________________________________________________________________________________

Pneutrol International Limited

[email protected]

This manual suits for next models

Table of contents

Other Mechan Safety Equipment manuals

Mechan

Mechan F Series User manual

Popular Safety Equipment manuals by other brands

Innova

Innova Xtirpa Instruction and safety manual

bolle SAFETY

bolle SAFETY B810 quick start guide

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T instruction manual

Hiltron security

Hiltron security POWER8E Installation and use manual

Hatco

Hatco B-950P installation guide

Sitec

Sitec TX MATIC operating manual

TEUFELBERGER

TEUFELBERGER GRIP 12 Manufacturer's information and instructions for use

MSA

MSA PremAire System Operation and instructions

AMC

AMC 1022M Series instruction manual

Trinity

Trinity CASS S3 Assembly manual

CMC

CMC Helitack HotSeat quick guide

Force

Force P-35 instruction manual

ACM

ACM SAFETY D200 Instructions and warnings

Honeywell

Honeywell Miller H-Design DuraFlex User instruction manual

ROCK

ROCK P-451 AS user guide

Power first

Power first 2XYR7A Operating instructions and parts manual

SCHUBERTH

SCHUBERTH SHP 28-C manual

Trango

Trango CINCH user manual