MBT LED SUPERFLY User manual
LED SUPERFLY
USER MANUAL
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initially start-up.
FEATURES
*LED flower effect in RGB and white Beams from the Fresnel lens
*DMX-512 control via regular DMX-controller (occupies 3 channels)
*Sound-controlled via built-in microphone
*Microphone-sensitivity adjustable via rotary-control
*Strobe effect
*11 internal programs
*Master/Slave function
*Particularly bright illuminating power of the 5mm RGB + white LEDs
*Advantages of LED-technology: extremely long life of the LEDs, low power consumption,
minimal heat emission, maintenance free with brilliant light radiation
OPERATION
After plugging into power source, the device starts running immediately.
STAND ALONE OPERATION
In Stand Alone Operation you can use the device without a controller.
For sound controlled operation set all DIP Switches to OFF.
You can do without a controller as the device features a built-in microphone,
which provides automatic sound control. You can adjust the sensitivity with the rotary-control on the rear panel,
SOUND-CONTROL OPERATION
For sound controlled operation set all DIP Switches to OFF.
MASTER/SLAVE OPERATION
The master/slave-operation enables that several devices can be synchronized and controlled by
one master-device. On the rear panel of the device you can find an XLR-jack and an XLR-plug,
which can be used for connecting several devices. Choose the device which is to control the
effects. This device then works as master-device and controls all
other slave-devices, which are to be connected to the master-device via a stereo shielded cable.
Connect the OUT-jack with the IN-plug of the next device.
Set all DIP Switches to OFF in order to determine the Master device. Set DIP Switches 1 and 10
to ON in order to determine the Slave device.
2
DMX-CONTROL OPERATION
You can control the devices individually via your DMX-controller. Every DMX-channel has a
different occupation with different features.
For DMX-controlled operation set DIP Switch 10 to ON.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next
fixture. Always connect one output with the input of the next fixture until all fixtures are
connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120
Ωresistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last fixture.
Addressing
Each device occupies 3channels. To ensure that the control signals are properly directed to
each device, the device requires addressing. This is to be adjusted for every single device by
changing the DIP-switches as set out in the table below.
The starting address is defined as the first channel from which the device will respond to the
controller. Please make sure that you do not have any overlapping channels in order to control
each device correctly and independently from any other fixture on the DMX data link. If two,
three or more devices are addressed similarly, they will work similarly.
Occupation of the DIP-switches:
Controlling:
After having addressed all devices, you may now start operating these via your controller.
DMX PROTOCOL
Channel 1 – LED groups/colors selection
Channel 2 – Strobe
000 – 005 Off
006 - 255 Flash, with increasing speed
Channel 3 – Internal Programs, Auto Mode, Sound Control
000 – 005 No function
3
006 – 025 Program 1
026 – 045 Program 2
046 – 065 Program 3
066 – 085 Program 4
086 – 105 Program 5
106 – 125 Program 6
126 – 145 Program 7
146 – 165 Program 8
166 – 185 Program 9
186 – 205 Program 10
206 – 225 Program 11
226 – 250 Auto Mode: Internal Programs
251 – 255 Sound Controlled Mode
CLEANING AND MAINTENANCE
We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use
alcohol or solvents! There are no serviceable parts inside the device except for the fuse. Maintenance and service
operations are only to be carried out by authorized dealers.
Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Take out the fuseholder under the power supply.
Step 2: Remove the old fuse from the fuseholder.
Step 3: Install the new fuse in the fuseholder.
Step 4: Replace the fuseholder in the housing and fix it.
Should you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by authorized dealers only in
order to avoid hazards.
TECHNICAL SPECIFICATIONS
Power supply: 120 V AC, 60 Hz
Power consumption: 20W
Number of DMX channels: 3
DMX-512 connection: 3-pin XLR
Sound-control: via built-in microphone via built-in microphone
Maximum ambient temperature Ta: 45° C
Maximum housing temperature TB (steady state): 60° C
Min.distance from flammable surfaces: 0.50 m
Min.distance to lighted object: 0.10 m
Fuse: F 1 A, 250V
Weight: 3 kg
Please note: Information is subject to change without prior notice.
Table of contents
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
