MaxLite LSU Series User manual

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 1

R V: 05/03/18

General afety Information

• To reduce the risk of death, personal injury or property damage from fire,

electric shock, falling parts, cuts/abrasions, and other hazards read all

warnings and instructions included with and on the fixture box and all

fixture labels.

• Before installing, servicing, or performing routine maintenance upon

this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires

should be performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation or

maintenance of the luminaires, consult a qualified licensed electrician

and check your local electrical code.

• DO NOT INSTALL DAMAG D PRODUCT!

• This fixture is intended to be connected to a properly installed and grounded

UL listed junction box.

WARNING:

RISK OF L CTRICALSHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring fixture

to the power supply.

• Turn off the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label

information.

• Make all electrical and grounded connections in accordance with the National lectrical

Code and any applicable local code requirements.

• All wiring connections should be capped with UL approved wire connectors.

CAUTION:

RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,

servicing or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

CAUTION:

RISK OF FIR

• Keep combustible and other materials that can burn away from luminaire and lamp/lens.

• MIN 90°C SUPPLY CONDUCTORS.

Models: LSU Series

Picture is for illustration purposes

only. Your model may vary.

General Wiring Diagram

CAUTION: Turn off electrical power at fuse

or circuit breaker box before wiring fixture to

the power supply.

Connecting panels to AC source supply:

All units must be individually connected to

the AC supply. (120-277 VAC)

Black = Line

White = Neutral

Green = Ground

Operating characteristic:

Voltage input: 120-277V 50/60 Hz

Operating temp: -4°F to 104°F

**Consult with dimmer control

manufacturer’s wiring instructions

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 2

R V: 05/03/18

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

Mounting Instructions

Before installation, ensure if power supply is disconnected. Cables must be connected in accordance

to instruction and proper standing rules.

1. Remove lens and wire way cover. Slide lens toward one end while lifting opposite end clear of fixture

housing. If not clearing easily, ensure lens has slide past retainer clip inside the end cap.

2. Next squeeze both sides of wire cover until they clear metal tabs and remove cover.

3. Select wiring access point and remove appropriate knockout.

4. Select installation point and locate studs.

Mounting Instructions

Before installation, ensure if power supply is disconnected. Cables must be connected in accordance

to instruction and proper standing rules.

5. For rear access points feed wires through hole.

6. Using 1” mounting screw or 3”x3/16 toggle bolts, secure fixture in place using keyhole slots provided.

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 3

R V: 05/03/18

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

Lens

Cover

Driver

crew

7. After making wiring connections, replace wire cover and diffuser into place.

8. Secure lens to housing by inserting clips at both ends of the fixture, as shown in the image below.

9. Restore power to branch circuit and energize the luminaire.

Metal Clips

Optional Motion ensor

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 4

R V: 05/03/18

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

Lens

Access crews

Upper Housing

Lower Housing

Coupling Assembly

tand offs

Mounting Key Holes

Motion ensor Option Wiring

etting & Adjusting Motion ensor

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 5

R V: 05/03/18

To make setting and control adjustments, you will need to access the three rotary DIP controls behind the lens.

Control Mode

The LOD-500 series features 8 different control modes

for selection via rotary DIP switch. Please refer to the

following table and sensor operation charts to select the

desired control mode.

W. ABCDE F G H

0SMA0SLA0S0T STMOD 0SHA 0SLAT0 0SMAT0 0SHAT0

MODE

(T ST)

234

MODE

TIME DIM

TIME

(10 minutes)

DIM

(OFF)(Factory set)

PO .

TIME

DIM

0123456

1’ 3’ 5’ 10’ 15’ 20’ 30’

OFF 5% 10% 20% 25% 33% 50%

Delay Time

The LOD-500 series offers 7 different delay

time settings via Accu-Set potentiometer.

The light will remain ON if sensor detects

occupant’s movement before the set delay

time expires. The Accu-Set potentiometer will

provide accurate delay time as the arrowhead

pointed.

Dim Level

The LOD-500 series offers 7 different dim

level settings via Accu-Set potentiometer.

The L D light will be dimmed as the level set

when condition of selected control mode

applies. The Accu-Set potentiometer will

provide accurate dim level as the arrowhead

pointed.

ensor Operation

Default

Parking

Profile

Default

tair

Profile

Battery Backup Option

Your MaxLite Utility wrap fixture may come equipped with a battery back up power system.

Please review all following remarks to prevent any damage or risk while installing or using your fixture:

This Option is covered under UL 1598 and is a factory assembled system. Any field installation will void the factory

warranty unless express written authorization is given in advance.

Contains Nickel-Cadmium Rechargeable Battery. Must be recycled or disposed properly.

Output LVL Compliant

Please note, your control is equipped with a quality

neoprene seal. This seal does expand over time

providing maximum sealing protection possible. If you

have any trouble re-installing the lens, a light coating

of WD-40 as lubricant, to the seal, will make installing

the lens easier. Care should be taken NOT to spray

lubricant into the DIP switches.

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 6

R V: 05/03/18

Battery Backup Option (Continued)

R AD AND FOLLOW ALL SAF TY INSTRUCTIONS!

1. To prevent high voltage from being present on yellow & orange output leads prior to installation,

converter connector must be open. Do not join converter connector until installation is complete and AC

power is supplied to the emergency driver.

2. This product is for use with an emergency L D lighting load and supplies up to 8.4 W of power(measured

at nominal battery voltage) at a maximum voltage of 60VDC and in emergency mode for a minimum of 90

minutes.

3. Make sure all connections are in accordance with the National lectrical Code or Canadian lectrical Code

and any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and convert

connector of the emergency driver before servicing.

5. This emergency driver is for factory installation only.

6. This product is suitable for use in damp locations where the ambient temperature is 0ºC minimum, +50ºC

maximum. Product is not suitable for heated air outlets and wet or hazardous locations.

7. An unswitched AC power source is required (120 - 277 VAC, 60 Hz)

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field

replaceable. Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualified service personnel.

13. Only apply to L D Driver which the output current less than 3.0A.

14. quipment should be mounted in locations and at heights where it will not be subjected to tampering by

unauthorized personnel. SAV TH S INSTRUCTIONS.

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 7

R V: 05/03/18

Your fixture comes with an

additional housing on rear to

enclose the battery back up

unit

Fixture

Housing

BBU

ide View

tep Down Transformer (347V Only)

CAUTION: Always disconnect power to luminaire before

attaching, removing or servicing. Risk of shock or fire.

1. Location of SDT.

Driver

SDT

Note: not suitable for BBU models.

MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from

MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the

Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with

the same or like Product.

Please refer to Maxlite’s website (at http://maxlite.com/resources/warranties) for the complete

terms and conditions of our warranty.

Limitation of Liability

TH FOR GOING WARRANTY IS XCLUSIV , AND IS TH SOL R M DY FOR ANY AND ALL CLAIMS,

WH TH R IN CONTRACT, IN TORT OR OTH RWIS ARISING FROM TH FAILUR OF PRODUCT AND IS IN

LI U OF ALL OTH R WARRANTI S, XPR SS OR IMPLI D, INCLUDING ALL WARRANTI S OF

M RCHANTABILITY OR FITN SS FOR A PARTICULAR PURPOS , WHICH WARRANTI S AR H R BY

XPR SSLY DISCLAIM D TO TH XT NT P RMITT D BY LAW AND, IN ANY V NT, SHALL B LIMIT D TO

TH WARRANTY P RIOD SP CIFI D ABOV . TH LIABILITY OF MAXLIT SHALL B LIMIT D TO TH T RMS

OF TH XPR SS WARRANTY S T FORTH H R IN. IN NO V NT WILL MAXLIT B LIABL FOR ANY

SP CIAL, INCID NTAL OR CONS QU NTIAL DAMAG S INCLUDING, WITHOUT LIMITATION, DAMAG S

R SULTING FROM LOSS OF US , PROFITS, BUSIN SS OR GOODWILL, LABOR COSTS, R MOVAL OR

INSTALLATION COSTS, D CR AS IN TH LIGHT OUTPUT OF TH LAMP, AND/OR D T RIORATION IN TH

LAMP’S P RFORMANC , WH TH R OR NOT MAXLIT HAS B N ADVIS D OF TH POSSIBILITY TH R OF.

UND R NO CIRCUMSTANC S SHALL MAXLIT ’S NTIR LIABILITY FOR A D F CTIV PRODUCT XC D

TH PURCHAS PRIC OF THAT PRODUCT. WARRANTY S RVIC S PROVID D UND R TH S T RMS AND

CONDITIONS DO NOT NSUR TH UNINT RRUPT D OP RATION OF PRODUCTS; MAXLIT SHALL NOT B

LIABL FOR DAMAG S CAUS D BY ANY D LAYS INVOLVING WARRANTY S RVIC .

This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to

state. Because some states or jurisdictions do not allow the exclusion or limitation of liability for consequential or

incidental damages, this limitation may not apply to you.

Warranty Information

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 mail: info@maxlite.com

Page: 8

R V: 05/03/18

Operating Instructions L U eries

MaxLite LED Utility Wrap Fixture

Table of contents

Other MaxLite Lighting Equipment manuals

MaxLite

MaxLite HLRM Series User manual

MaxLite

MaxLite maxLED SEC12U50BPC12 User manual

MaxLite

MaxLite WPCS Series User manual

MaxLite

MaxLite MSF Series User manual

MaxLite

MaxLite WPOP Series User manual

MaxLite

MaxLite External U-Bend T8 User manual

MaxLite

MaxLite CPL Series User manual

MaxLite

MaxLite C1D2 User manual

MaxLite

MaxLite MLFPG4-LHMSKIT User manual

MaxLite

MaxLite CID1 User manual

MaxLite

MaxLite TRK WS Series User manual

MaxLite

MaxLite MPulse Bollard Luminaire User manual

MaxLite

MaxLite PhotonMax PH Series User manual

MaxLite

MaxLite QM Plus Series User manual

MaxLite

MaxLite MLFP14DP4535 User manual

MaxLite

MaxLite AR Series User manual

MaxLite

MaxLite HL-LI2440UEM0 User manual

MaxLite

MaxLite LED PLL DirectFit Series User manual

MaxLite

MaxLite HL-WP Series User manual

MaxLite

MaxLite HL Series User manual

MaxLite

MaxLite HLRS Series User manual

MaxLite

MaxLite ML2LAxP Series User manual

MaxLite

MaxLite maxLED MAL Series User manual

MaxLite

MaxLite ML2LALABNU249CSEM User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions