Matsusada Precision XR Series User manual

XR SERIES

Instruction Manual

Rev. 2.1

B/N 077.9.014 *077.9.014*

ⅰ

SAFETY

1. BE SURE TO GROUND!!

Be sure to ground the power supply unit before use.

2. DO NOT TOUCH ANY HIGH VOLTAGE TERMINALS!!

Do not operate the power supply unless who is familiar with the operation process, the hazards

of high voltage, and the treatment for the electrical shock is present.

3. UNDERSTAND THE HAZARDS OF HIGH VOLTAGE!!

In case you let somebody operate the power supply for you, must be sure that he/she fully

understands the hazards of high voltage and the areas where never can be touched.

4. CUT OFF THE POWER BEFORE TOUCH THE UNIT!!

Cut off the power, and check that the power is OFF, before you touch the power supply.

Capacitors in the output circuit are still charged and dangerous even after the power has been

cut off.Discharge all remaining high voltage by grounding them.

5. DISCONNECT THE INPUT LINES(AC LINES) !!

In case you need to touch the inside of the power supply following instruction manual, cut off

the power and disconnect the input lines(AC lines), and ground all the capacitors and high

voltage section.

Don’t remove the case or touch the inside of power supply unless so instructed in the

instruction manual.

6. OPERATE THE POWER SUPPLY WITH YOUR RIGHT HAND!!

In order to avoid the electric shock to your important organs, operate the power supply with

your right hand and keep your left hand off from the power supply.

This power supply unit generates high voltage and energy.

Electric shock may lead to death or serious injury.

Be sure to follow the instructions below and handle the unit with caution.

ⅱ

Various symbols are used in this instruction manual and on the product for ensuring safety.

What will be caused by ignoring the instructions given with the symbols or by improper handling

are classified as shown below. Read carefully and understand the descriptions before

proceeding to the main body of this manual.

Symbols

Meanings of the Symbols

Some of the symbols used

are shown on the right.

Indicates that which requires caution.

Indicates that which forbidden.

Indicates that which must be done.

Indicates electric shock hazard.

failure to follow the instructions with this indication may lead to death or serious injury.

failure to follow the instructions with this indication may lead to injury or damage in property.

Warning:

Caution:

！



！



！



！



！



Warning

Do not touch the output terminal or the

leads or load connected to it while the

unit is in operation or immediately after it

is stopped. Otherwise it may cause

electric shock or injury.

Do not install the unit in a place subject

to steam or water vapor.

Otherwise it may cause poor insulation

and lead to fire or electric shock.

Do not install the unit in a place subject

to dew condensation.

Otherwise it may cause electric shock.

Do not modify or damage the cables.

Otherwise it may cause electric shock.

Be sure to ground the unit to avoid a rare

possibility of electric shock.

Otherwise it may lead to fire, electric

shock or injury.

Do not place any object on the unit.

Dangerous situations may occur if the

object drops or falls.

Do not put any object in the unit.

It may cause damage.

Do not disassemble, remodel or repair the

unit. High voltage may be built up inside,

which may cause electric shock.

Disassembly, remodeling or repair hamper

ensuring of safety and may lead to

dangerous situations.

Do not install the unit outdoors or in a

place subject to leaking of water, flood

or snow.

Otherwise it may cause electric shock.

DISASSEMBLY

GROUND

ⅲ

■ After reading this manual, be sure to store it in a place convenient for the users so that it can be referred

to at anytime.

！



Caution

Do not install the unit upside down or

on a wrong side.

Insufficient heat release may cause

deterioration of parts, which may

generate smoke or set fire.

Do not use the unit in a place subject to

high temperature or in an enclosed,

limited area.

It not only hampers the unit from

achieving its performance but also

causes deterioration of parts leading to

smoking or burning.

Do not wipe the unit with chemicals

(such as thinner) or wet cloth.

It may allow water inside leading to

electric shock, electrical leak or burning.

Do not cover the vent holes of the unit.

Vent holes are provided to prevent

elevation of temperature inside.

Covering them not only hampers the unit

from achieving its performance but also

causes deterioration of parts, which may

generate smoke or set fire.

Do not install the unit and the remote

controller in a place subject to direct

cold air. Condensation may lead to

electrical leak/burning.

Do not install the unit in a place subject

to corrosive gas or liquid (such as a

place where chemicals are handled).

Deterioration of parts may cause

generation of smoke or burning.

NO NO

ⅳ

(1) RESCUE

FREE VICTIM FROM CONTACT WITH LIVE CONDUCTOR QUICKLY.

AVOID CONTACT WITH FITHER LIVE CONDUCTOR OR VICTIM’S BODY.

Shut off high voltage at once and ground circuit. If high voltage cannot be turned off

quickly, ground circuit.

An ax with a dry wooden handle may be used to cut high voltage line.

Use extreme caution to avoid resulting electric flash.

If circuit cannot be broken or grounded, use a dry board, dry clothing, or other

nonconductor to free victim.

(2) SYMPTOMS

NEVER ACCEPT ORIDNARY AND GENERAL TESTS FOR DEATH.

Symptoms of electric shock may include unconsciousness, failure to breathe, absence of

pulse, pallor, and stiffness, as well as severe burns.

WHENEVER VICTIM IS NOT BREATING PROPERLY, GIVE ARTIFICIAL RESPIRATION.

(3) TREATMENT

START ARTIFICIAL RESPIRAITON IMMEDIATELY.

Perform artificial respiration at scene of accident, unless victim’s or operator’s life is

endangered. IN THIS CASE ONLY, remove victim to safe location nearby, if new location

is more than few feet away, give artificial respiration while victim is being moved.

After starting artificial respiration, continue without loss of rhythm for at least FOUR

HOURS, or until victim is breathing without help.

If you have to change operators while giving artificial respiration, do so without losing

rhythm of respiration.

(4) AFTER VICTIM REVIVES

Be prepared to resume artificial respiration, as he may stop breathing again.

When victim is CONPLETELY CONSCIOUS, give him a stimulant (NOT AN ALCOHOLIC

DRINK) such as teaspoonful of aromatic spirits of ammonia in a small glass of water, hot

coffee, or hot tea.

Keep victim warm and lying down until he has been conscious for at least fifteen minutes.

First-aid procedures to be implemented in case of electrical shock

ⅴ

1.POSITION VICTIM

Place victim in face-upward position an kneel close to his ear.

2.CLEAR THROAT

Turn head to one side quickly wipe out any fluid, mucus, or

foreign body from mouth and throat with fingers.

3.OPEN AIR PASSAGE

Tilt head back and extend neck to open air passage.

4.LIFT JAW FORWARD

Ice thumb in victim’s mouth and grasp jaw firmly. Lift jaw

forward to pull tongue out of air passage. Do not attempt to

hold or depress tongue.

5.PINCH NOSTRILS CLOSED

With other hand pinch nostrils closed to prevent air leak.

6.FORM TIGHT SEAL WITH LIPS

Rescuer’s wide-open mouth completely surrounds and seals

open mouth of victim,

This is not a kissing or puckered position-mouth of rescuer

must be wide-open,

7.BLOW

Exhale firmly into victim’s mouth until chest is seen to lift.

This can be seen by rescuer without difficulty.

8.REMOVE MOUTH AND INHALE

During this time, rescuer can hear and feel escape for air from

lungs.

Readjust position if air does not flow freely in and out of victim’s

lungs.

Continue at a rate of 12 to 20 times per minute.

Breathing should be normal in rate with only moderate increase

in volume so that rescue breathing can be continued for long

periods without fatigue. Do not breathe too forcibly or too

large a volume if victim is an infant or small child.

8.Remove mouth and

inhale

7.Blow

3.Open air

passage

2.Clear throat

Artificial respiration

1-1 Introduction

Thank you very much for your purchase of our product, HIGH VOLTAGE POWER SUPPLY.

We do our best to exercise quality control of our products. You will please handle this unit

properly according to this operation manual so that you may display the full capacity of this

unit, operate it for smoothly in high efficiency for many years to come and safely.

We have done our best to prepare this operation but if you should recognize a doubtful or

unknown point or an omission, we are very sorry but would you please contact our company

immediately.

1-2 Unpacking the High Voltage Power Supply

When unpacked, you will please check the following accessories are enclosed together with

the power supply body.

〈Accessories〉

・ Instruction Manual

・ Output cable

・ Connector Screw terminal 2pin

Screw terminal 3pin

Screw terminal 4pin

D-type connector 9pin

・ Screw 2pc.

1-3 Environmental requirements

・ Install a high voltage power supply horizontally and use it.

・ Never place an object on the high voltage power supply.

・ Provide an ample space to the upper, right and left side of the high voltage power supply.

Use it at the place where the ventilating condition is as good as possible.

・ Avoid using the unit at such places where it is very dusty or there is much corrosive gas

etc.

1 Introduction

(1pc.)

1-4 Points to be careful about in handling and care

WHEN TOUCHING LOAD AFTER TURNING OFF A HIGH TENSION

1. Make the setting of an output voltage to zero (0). Turn off the INTLK switch.

2. Turn the input voltage (24 VDC) OFF.

3. Earthling an output for longer than 10 seconds, check and confirm that the voltage is zero

at another high tension voltmeter. It is especially dangerous that the load is capacitate

or a long cable is attached there to.

4. Make it a rule to touch load with right hand.

How to GROUND

・ For safe operation, be sure to ground the ground terminal of power supply at one point

on the ground.

If the Load frame is not grounded

If the Load frame is grounded

・ Be sure to complete grounding as shown above. Inadequate grounding may lead to

electric shock of damage to the power supply unit, which is dangerous.

・ If there is a possibility of development of a short-circuiting of load or discharging, make

larger and shorter the grounding conductor.

IN ORDER TO INSURE SAFETY THE GROUND

TERMINAL SHOULD BE EARTHED AT ALL TIME.

1 Introduction

output cable

ground terminal

load frame

load

Wires should be :

・ more than 5SQ

・ less than about 2m

・ not bared

Ground at one point

Wires should be :

・more than 5SQ

・ less than about 2m

・not bared

output cable

ground terminal

ground

load frame

load

Ground at one point

Other manuals for XR Series

Table of contents

Other Matsusada Precision Power Supply manuals

Matsusada Precision

Matsusada Precision DOKF Series User manual

Matsusada Precision

Matsusada Precision R4K-80 Series User manual

Matsusada Precision

Matsusada Precision R4G Series User manual

Matsusada Precision

Matsusada Precision PSS2en-DCPS User manual

Matsusada Precision

Matsusada Precision PVCE Series User manual

Matsusada Precision

Matsusada Precision R4GT Series User manual

Matsusada Precision

Matsusada Precision AMP Series User manual

Matsusada Precision

Matsusada Precision DOSF Series User manual

Matsusada Precision

Matsusada Precision PKTS Series Installation guide

Matsusada Precision

Matsusada Precision DRK Series User manual

Matsusada Precision

Matsusada Precision PRKT Series User manual

Matsusada Precision

Matsusada Precision DRJ Series Installation guide

Matsusada Precision

Matsusada Precision AMPS Series User manual

Matsusada Precision

Matsusada Precision PSS2en-HVPS User manual

Matsusada Precision

Matsusada Precision ECA Series User manual

Matsusada Precision

Matsusada Precision DOEF Series User manual

Matsusada Precision

Matsusada Precision eK-FG2 User manual

Matsusada Precision

Matsusada Precision REK Series User manual

Matsusada Precision

Matsusada Precision ECD-BC Series User manual

Matsusada Precision

Matsusada Precision VOL Series User manual

Matsusada Precision

Matsusada Precision R4K-36 Series User manual

Matsusada Precision

Matsusada Precision DOP Series User manual

Matsusada Precision

Matsusada Precision RE Series User manual

Matsusada Precision

Matsusada Precision EQ Series User manual

Popular Power Supply manuals by other brands

Monacor

Monacor PS-12CCD instruction manual

VOLTIMA

VOLTIMA MagicBox 15 Installation and operating instructions

Agilent Technologies

Agilent Technologies 6032A Service manual

Miller

Miller Auto Deltaweld 452 owner's manual

BCP

BCP PUOUBK How to install

HC 2210 manual

Puls

Puls CT5.241 installation manual

OCZ

OCZ ZX1250W Technical specifications

iseg

iseg ECH 238 manual

Power

Power XXL A Series instruction manual

Agilent Technologies

Agilent Technologies 6631B Service manual

Renogy

Renogy PHOENIX 300 user guide

HP 6200B Operating and service manual

Epson

Epson Stylus Scan 2500 Product information sheet

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 manual

Puls

Puls MiniLine ML50.100 instruction manual

Puls

Puls AS-Interface SLA4.100 installation manual

Kenwood

Kenwood PS-60 instruction manual