Marvel 3SWCE-BB-G User manual

A Division of Northland Corporation

A 3 1/2 INCH TOE KICK OR 7 SCREWS FOR A 4 INCH TOE KICK.

THE WOOD FRAME. A TOTAL OF 8 SCREWS WILL BE NEEDED. FOR

2. ONLY USE PAN HEAD SCREWS.

3. DO NOT SELECT A SCREW THAT IS LONGER THAN THE WOOD

4. USE RECOMMENDED PILOT HOLES FOR THE FRAME MATERIAL (SEE

1. A #8 PAN HEAD WOOD SCREW SHOULD BE USED TO PROPERLY SECURE

THICKNESS AT THE SCREW LOCATIONS.

CHART BELOW)

THIS SURFACE PARALLEL TO THE UNIT.

(RIGHT HAND SWING DOOR SHOWN)

1. ATTACH THE TOP AND BOTTOM DOOR HINGES TO THE DOOR WITH THE

10-32 MACHINE SCREWS AND A 1/8 INCH ALLEN HEAD DRIVER AS SHOWN IN

THE FIGURE BELOW.

2. PRESS IN THE SHOULDER BUSHINGS TO THE TOP AND BOTTOM DOOR

HINGES. MAKE CERTAIN THAT THE SHOULDER IS TO THE OUTSIDE OF THE

DOOR AS SHOWN IN THE FIGURE BELOW.

3. TEST FIT THE DOOR TO THE UNIT TO MAKE CERTAIN DOOR WILL HANG

CORRECTLY. THE DOOR IS HUNG CORRECTLY WHEN THE TOP OF THE DOOR

IS PARALLEL TO THE TOP OF THE UNIT. ADJUSTMENTS CAN BE MADE BY

LOOSING THE DOOR HINGE MACHINE SCREWS AND MOVING THE DOOR HINGE

ON THE DOOR.

4. TIGHTEN ALL FOUR MACHINE SCREWS AFTER ADJUSTMENTS HAVE BEEN

MADE.

5. REMOVE THE DOOR FROM THE UNIT BY REMOVING THE UNITS TOP HINGE

SET SCREW AND ANGLING THE DOOR OFF OF THE BOTTOM HINGE PIN.

DOOR FRONT

SURFACE

DOOR HINGE

SCREW HOLES

TYPICAL

TOP AND

BOTTOM

DOOR HINGE

ASSEMBLY

SHOULDER BUSHING

DOOR HINGE

10-32 MACHINE

SCREWS

TO THE UNIT AND WHEN THE WOOD IS POSITIONED

HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED

CLEARANCE HOLE. LOCATE AND DRILL USING DOOR

(NON-FACE) SIDE

MOUNTING SURFACE

ON DOOR.

Ø0.25 X 0.375 DEEP HINGE SCREW

SURFACE

TOP

TO THE UNIT AND WHEN THE WOOD IS POSITIONED

HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED

CLEARANCE HOLE. LOCATE AND DRILL USING DOOR

MOUNTING SURFACE

(NON-FACE) SIDE

MOUNTING SURFACE

(NON-FACE) SIDE

ON DOOR.

Ø0.25 X 0.375 DEEP HINGE SCREW

(NON-FACE) SIDE

MOUNTING SURFACE

(NON-FACE) SIDE

TYP

7.81

(COVERS THE ENTIRE DOOR EXTRUSION)

TO THE UNIT AND WHEN THE WOOD IS POSITIONED

HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED

CLEARANCE HOLE. LOCATE AND DRILL USING DOOR

FOR A 3.5 INCH TOE KICK

ON DOOR.

Ø0.25 X 0.375 DEEP HINGE SCREW

TOE KICK HEIGHT)

(TO MATCH EXISTING CABINETRY

OPTIONAL FOR A 4 INCH TOE KICK

TO THE UNIT AND WHEN THE WOOD IS POSITIONED

HINGE HOLE AFTER THE DOOR HAS BEEN ALIGNED

CLEARANCE HOLE. LOCATE AND DRILL USING DOOR

(NON-FACE) SIDE

MOUNTING SURFACE

ON DOOR.

Ø0.25 X 0.375 DEEP HINGE SCREW

MOUNTING SURFACE

BOTTOM HINGE CORNER

CAUTION

DOOR CAN BECOME

DISENGAGED IF WASHERS

ARE NOT INSTALLED

TOP HINGE CORNER

SHOULDER BUSHING

.75 OD X .443 ID

.75 OD X .257 ID

SHOULDER BUSHING

WASHER

3 NYLON

HARDWARE

COMPONENTS

AT BOTTOM

HINGE

HARDWARE

COMPONENTS

AT TOP HINGE

2 NYLON

NOT INSTALLED AS SHOWN

COMPONENTS ARE NOT

PROPERLY-IF ALL NYLON

DOOR MAY NOT SWING

.625 OD X .218 ID

WASHER

CAUTION

6. INSTALL THE DOOR TO THE UNIT. USE THE SUPPLIED PLASTIC WASHERS AS SHOWN IN THE FIGURE BELOW.

2. PEEL BACK DOOR GASKET TO EXPOSE THE SCREW HOLES.

3. SET THE WOOD FRAME FLUSH TO THE FRONT OF THE DOOR IN THE DESIRED LOCATION. CLAMP WOOD FRAME TO

THE TOP HINGE. REMOVE THE DOOR BY ANGLING THE DOOR OFF OF THE BOTTOM HINGE PIN.

1. IF THE DOOR IS ATTACHED TO THE UNIT, REMOVE IT BY UNSCREWING THE TOP ALLEN HEAD SET SCREW AT

THE DOOR IF NECESSARY.

4. INSERT THE WOOD SCREWS THROUGH THE BACK OF THE DOOR INTO THE PILOT HOLES IN THE WOOD FRAME AND

5. REINSTALL DOOR GASKET BY PRESSING INTO DOOR CHANNEL. MAKE CERTAIN THE CORNERS ARE INSERTED FULLY.

7. REALIGNING THE DOOR MAY BE NECESSARY. ANY FINAL DOOR ADJUSTMENTS CAN BE MADE USING A 1/8 INCH ALLEN

8. ATTACH THE DOOR LIGHT STRIKER PLATE AS SHOWN USING THE HEX OR PHILLIPS HEAD SCREWS PROVIDED. MAKE

TIGHTEN.

HEAD DRIVER TO ADJUST THE DOOR'S HINGES (SEE FIGURE BELOW).

CERTAIN THE LIGHT IS ABLE TO TURN ON AND OFF WHEN THE DOOR IS OPENED AND CLOSED.

9. ATTACH THE DOOR TO THE UNIT BY REVERSING STEP NUMBER 1 ABOVE.

CAUTION

DOOR CAN BECOME

DISENGAGED IF WASHERS

ARE NOT INSTALLED CABINET HINGE

WOOD

FRAME

WOOD

FRAME

DOOR HINGE

HINGE HARDWARE

INSTALLATION DETAILS.

Other manuals for 3SWCE-BB-G

This manual suits for next models

Other Marvel Refrigerator manuals

Popular Refrigerator manuals by other brands

Bonnet Neve

Bonnet Neve SKYVIEW PLUS User instructions

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Instruction book

Sharp

Sharp SJ-BA31IEXW2-EU user manual

CORBERO

CORBERO CC2300MCW Instruction booklet

KitchenAid

KitchenAid 2205264 Use and care guide

Stengel

Stengel KU 1101 A++ user manual

NEFF

NEFF KI181 Series user manual

Hoshizaki

Hoshizaki Reach-In instruction manual

Amana

Amana ASD2524VES00 User instructions

BOMANN

BOMANN KGC 213 instruction manual

Danby

Danby DAR044A1SLDD Owner's use and care guide

Samsung

Samsung RF323TE user manual

Beko

Beko CSA31022 Instructions for use

IKEA

IKEA FROSTIG C 185 E manual

Electrolux

Electrolux ER 6821 D Instruction book

True

True TS-28 Specifications

Frigidaire

Frigidaire FSC23R5DW9 installation guide

Beko

Beko LSP4579W Instructions for use