Manrose CRA100T User manual

INSTALLATION INSTRUCTIONS

Switch off mains supply before making any electrical connections.

Installation must be supervised by a qualified electrician.

This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory and mental capabilities

or lack of experience and knowledge if they have been given

supervision or instruction concerning the use of the appliance in a

safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children

without supervision.

Precautions must be taken to avoid the back-flow of gases into the

room from the open flue of gas or other open-fire appliances when

mounted in outside windows or walls.

Fan must be disconnected from electrical power before any

maintenance is carried out.

CRA100T

Continuous Running Axial Fan

Wiring

1. Switch off mains supply before making electrical

connections. If in any doubt contact a qualified

electrician.

2. These units are for fixed wiring only. A flexible cord

must not be used. All wiring must be fixed securely

and the cable to the fan should be a minimum of

1mm2in section. All wiring must comply with current

I.E.E. Regulations or local regulations if outside the

UK.

3. A double pole fused spur having contact separation

of at least 3mm in all pole must be used and fitted

with a 3A fuse.

4. This fan is double insulated and does not require an

earth connection.

5. The fan should not be accessible to a person using

either the shower or the bath.

Location

1. When installing fan through an external wall, an

external wall grille must be fitted at all times.

2. For best results this Extractor Fan should be fitted

as high on the wall as possible, or if preferred, on

the ceiling. Note: Pullcord models should not be

installed in a ceiling.

3. When installing Humidity or Timer fans ensure

the electronic circuit board is at the top of the fan.

4. Do not install the unit within a shower cubicle

or anywhere else where there is a risk of being

sprayed with water (Please see our range of

showerfans for these installations.).

5. If the fan is installed in a room containing a fuel

burning appliance, the installer must ensure that

the air replacement is adequate for both the fan

and the fuel burning appliance.

IMPORTANT: READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION

DO NOT - install this product in areas where the following may be present or occur:

• Excessive oil or a grease laden atmosphere.

• Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

SAFETY AND GUIDANCE NOTES

1. When the Fan is used to remove air from a room containing a fuel-burning appliance, ensure that the air

replacement is adequate for both the fan and the fuel-burning appliance.

2. The Fan should not be used where it is liable to be subject to direct water spray for prolonged periods of time.

3. Where ducted Fans are used to handle moisture-laden air, such as a bathroom, a condensation trap should

be fitted in any vertical exhaust ducts. Horizontal ducts should be arranged to slope slightly downwards away

from the Fan. Ducts passing through cold voids must be suitably insulated.

4. This product should not be disposed of with household waste. Please recycle where facilities exist. Check

with your local authority for recycling advice.

DESCRIPTION

The Continuous Running Axial 100mm fan is a continuously running extract fan for kitchens, utility rooms, bath-

rooms and toilets. It has an 8L/s trickle speed and 15L/s boost, the fan is fitted with a fixed 15 minute overrun

timer.

A. INSTALLATION

PANEL/CEILING MOUNTING

1. For panel/ceiling mounting the fan should be installed into a closed duct system of at least 1.2m long or

protected by an exterior air grille that must comply with the standard requirements of your country to prevent

access to the fans impeller.

2. Cut a 105mm diameter hole.

3. Loosen the screw at the bottom of the grille and remove the front grille. Mark the screw centres through the

holes in the fan back plate. Drill, plug and screw into position.

4. Attach ducting as required for the installation.

5. Wire the fan as described in the Wiring section.

6. After installation, ensure impeller rotates freely.

7. Replace the grille and tighten the retaining screw.

WALL MOUNTING

1. For wall mounting cut a 115mm diameter hole through the wall and insert the wall sleeve. Slope the sleeve

slightly downwards away from the fan. Cut to length and cement both ends into position flush with the wall

faces.

2. Loosen the screw in the bottom of the grille and remove the front grille. Mark the screw centres through the

holes in the fan back plate. Drill, plug and screw into position.

3. Fix exterior grille into position with the louvres positioned downwards. (Note:- The grille must comply with the

standard requirements of your country to prevent access to the fans impeller).

4. Wire the fan as described in Section B-Wiring. Adjust any settings as required (see Section C-Setup).

5. After installation, ensure impeller rotates freely.

6. Replace the grille and tighten the retaining screw.

B. WIRING.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM THE

POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

• The cross - sectional area of supply cord used should be ranged from 1 - 1.5mm2.

• Cable entry can only be made from the rear of the fan.

• The extraction fan is suitable for connection to 220-240V 50Hz supply.

• The fan is a class II double insulated product and MUST NOT be earthed.

1. Select and follow the appropriate wiring diagram. (Fig. 1, 2 & 3)

2. Check all connections have been made correctly and ensure all terminal connections and cable clamps are

securely fastened.

Fig.1 Continuous trickle (8 L/s) with no remote boost facility. Link Switched Live terminal to Neutral terminals.

SWITCHED

SPUR

FAN

MAINS

220-240VAC

LINK

Fig.2 Continuous Boost (15 L/s) with no trickle facility. Note:- Link must be fitted between Live & Switched Live

terminals.

SWITCHED

SPUR

FAN

MAINS

220-240VAC

LINK

Fig.3 Continuous trickle (8 L/s) with boost facility (15L/s) via remote switch.

SWITCHED

SPUR

FAN

MAINS

220-240VAC

Two Wire systems

Three Wire Systems

PLEASE DISPOSE OF

USED FAN AT YOUR

LOCAL CIVIC AMENITY

SITE. DO NOT DISPOSE

IN DOMESTIC WASTE

077632

SERVICING AND MAINTENANCE.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no build

up of dirt or other deposits.

2. Carefully push the front panel of the grille upwards away from the base part of the grille (Fig. 5).

Wipe the inlets and front face with a damp cloth until clean.

The fan has sealed for life bearings, which do not require lubrication.

1. Loosen screw.

2. Pull grille

slightly away

from bottom

edge.

3. Push grille upwards until

clear from the fan chassis.

C. SETUP

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM THE

POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE

Accessing the wiring and control settings – (Fig. 5)

09/15

Table of contents

Other Manrose Fan manuals

Manrose

Manrose FAN7183 User manual

Manrose

Manrose LED Series User manual

Manrose

Manrose MRUF150WH Assembly instructions

Manrose

Manrose M200P User manual

Manrose

Manrose LED Series Installation guide

Manrose

Manrose EXTRACT-A-LITE Service manual

Manrose

Manrose HYPER150 User manual

Manrose

Manrose FAN5371 User manual

Manrose

Manrose PRO Series User manual

Manrose

Manrose CRA100HT&T User manual

Manrose

Manrose FAN0618 User manual

Manrose

Manrose CLASSIC XF150 User manual

Manrose

Manrose Showerlite LEDSLKTC User manual

Manrose

Manrose FAN0085 User manual

Manrose

Manrose FAN2120 User manual

Manrose

Manrose FAN0531 User manual

Manrose

Manrose FAN0531 User manual

Manrose

Manrose CLASSIC XF125 User manual

Manrose

Manrose FAN0046 User manual

Manrose

Manrose FAN7500 User manual

Manrose

Manrose LED Series User manual

Manrose

Manrose SLIM F100 User manual

Manrose

Manrose COMT Series User manual

Manrose

Manrose PRO Series User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual