Makita SP6000 User manual
SP6000
0976201
EN Plunge Cut Circular Saw Instruction manual
ZHCN 电动圆锯 使用说明书
ID Gergaji Lingkaran Pemotongan
Petunjuk penggunaan
Benam
VI Maùy Cöa Ñóa Caàm Tay Hoaït Taøi lieäu höôùng daãn
Ñoäng Baèng Ñoäng Cô Ñieän
TH
2
1000114 2000157
3000154 4000156
5000194 6000147
7000029 8007656
21
3
9007669 10 007670
11 007657 12 007659
13 007660 14 007661
15 007671 16 007664
3
3
4
4
5
6
7
8
910
A
B
11
12
4
17 007663 18 007684
19 007662 20 007655
21 007658 22 007672
23 007673 24 007674
13
14
15 11
15
14
16
17
18
19
20
21
22
5
25 007685 26 007666
27 007675 28 007686
29 007678 30 007667
31 007668 32 001145
23
24
25
26
27
B
AA
B
28
29
30
6
33 007676
31
32
7
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change ithout
notice.
• Specifications may differ from country to country.
• The eight may differ depending on the attachment(s). The lightest and heaviest combination, according to EPTA-
Procedure 01/2014, are sho n in the table.
Symbols END201-7
The follo ing sho the symbols used for the equipment.
Be sure that you understand their meaning before use.
... Read instruction manual.
............. DOUBLE INSULATION
Intended use ENE067-2
The tool is specially intended for performing plunge cuts.
The tool is also intended for rip and cross cuts in ood. If
the tool is equipped ith proper circular sa blade, the
tool can be used for aluminum board, plastic board, siding
board and metal all panels.
Power supply ENF002-2
The tool should be connected only to a po er supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets ithout earth ire.
General ower tool safety
warnings GEA012-2
WARNING: Read all safety warnings, instructions,
illustrations and specifications pro ided with this
power tool. Failure to follo all instructions listed belo
may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term “po er tool” in the arnings refers to your
mains-operated (corded) po er tool or battery-operated
(cordless) po er tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosi e
atmospheres, such as in the presence of
flammable liquids, gases or dust. Po er tools
create sparks hich may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Ne er
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets ill
reduce risk of electric shock.
2. A oid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
1. Clamping scre
2. Blade lo er limit stopper
3. Quick stop button
4. Clamping scre s
5. Tool base
6. Positive stopper
7. Lever
8. Bevel angle shifting lever
9. Base
10. Cutting line
11. Lock-off button
12. S itch trigger
13. Speed adjusting dial
14. Hex rench
15. Locking lever
16. Shaft lock
17. Hex bolt
18. Outer flange
19. Sa blade
20. Inner flange
21. Vacuum cleaner
22. Dust port
23. Adjusting scre s
24. Slide lever
25. Rip fence (Guide rule)
26. Rear edge of tool base
27. Fixed stop
28. Adjusting scre for 90°
29. Adjusting scre for 45°
30. Limit mark
31. Scre driver
32. Brush holder cap
Model SP6000
Blade diameter 165 mm
Max. cutting depth
at 90° 56 mm
at 45° 40 mm
at 48° 38 mm
No load speed (min-1) 2,200 - 6,400
Overall length 341 mm
Net eight 4.1 kg
Safety class /II
8
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a po er tool ill increase
the risk of electric shock.
4. Do not abuse the cord. Ne er use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
mo ing parts. Damaged or entangled cords increase
the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
una oidable, use a residual current de ice (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
7. Use of power supply ia an RCD with a rated
residual current of 30 mA or less is always
recommended.
8. Power tools can produce electromagnetic fields
(EMF) that are not harmful to the user. Ho ever,
users of pacemakers and other similar medical
devices should contact the maker of their device and/
or doctor for advice before operating this po er tool.
9. Do not touch the power plug with wet hands.
10. If the cord is damaged, ha e it replaced by the
manufacturer or his agent in order to a oid a
safety hazard.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention hile operating po er tools
may result in serious personal injury.
2. Use personal protecti e equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions ill reduce
personal injuries.
3. Pre ent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying po er tools ith your finger on the
s itch or energising po er tools that have the s itch
on invites accidents.
4. Remo e any adjusting key or wrench before
turning the power tool on. A rench or a key left
attached to a rotating part of the po er tool may result
in personal injury.
5. Do not o erreach. Keep proper footing and
balance at all times. This enables better control of
the po er tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
mo ing parts. Loose clothes, je ellery or long hair
can be caught in moving parts.
7. If de ices are pro ided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury ithin a fraction of a second.
9. Always wear protecti e goggles to protect your
eyes from injury when using power tools. The
goggles must comply with ANSI Z87.1 in the USA,
EN 166 in Europe, or AS/NZS 1336 in Australia/
New Zealand. In Australia/New Zealand, it is
legally required to wear a face shield to protect
your face, too. (Fig. 1)
It is an employer’s responsibility to enforce the
use of appropriate safety protecti e equipments
by the tool operators and by other persons in the
immediate working area.
Power tool use and care
1. Do not force the power tool. Use the correct power
tool for your application. The correct po er tool ill
do the job better and safer at the rate for hich it as
designed.
2. Do not use the power tool if the switch does not
turn it on and off. Any po er tool that cannot be
controlled ith the s itch is dangerous and must be
repaired.
3. Disconnect the plug from the power source and/or
remo e the battery pack, if detachable, from the
power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the po er tool accidentally.
4. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Po er tools are dangerous in the hands
of untrained users.
5. Maintain power tools and accessories. Check for
misalignment or binding of mo ing parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If damaged,
ha e the power tool repaired before use. Many
accidents are caused by poorly maintained po er
tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools ith sharp cutting edges are
less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the po er tool for operations
different from those intended could result in a
hazardous situation.
8. Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allo for safe handling and
control of the tool in unexpected situations.
9. When using the tool, do not wear cloth work
glo es which may be entangled. The entanglement
of cloth ork gloves in the moving parts may result in
personal injury.
Ser ice
1. Ha e your power tool ser iced by a qualified
repair person using only identical replacement
9
parts. This ill ensure that the safety of the po er tool
is maintained.
2. Follow instruction for lubricating and changing
accessories.
CIRCULAR SAW SAFETY
WARNINGS GEB144-3
Cutting procedures
1. DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
are holding the sa , they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade belo the
orkpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible belo the orkpiece.
4. Ne er hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a
stable platform. It is important to support the ork
properly to minimise body exposure, blade binding, or
loss of control. (Fig. 2)
5. Hold the power tool by insulated gripping
surfaces, when performing an operation where the
cutting tool may contact hidden wiring or its own
cord. Contact ith a “live” ire ill also make exposed
metal parts of the po er tool “live” and could give the
operator an electric shock.
6. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond ersus round) of arbour holes. Blades
that do not match the mounting hard are of the sa
ill run off-centre, causing loss of control.
8. Ne er use damaged or incorrect blade washers or
bolt. The blade ashers and bolt ere specially
designed for your sa , for optimum performance and
safety of operation.
Kickback causes and related warnings
- kickback is a sudden reaction to a pinched, jammed or
misaligned sa blade, causing an uncontrolled sa to
lift up and out of the orkpiece to ard the operator;
- hen the blade is pinched or jammed tightly by the kerf
closing do n, the blade stalls and the motor reaction
drives the unit rapidly back to ard the operator;
- if the blade becomes t isted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the ood causing the blade to climb out
of the kerf and jump back to ard the operator.
Kickback is the result of sa misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given belo .
1. Maintain a firm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade, but
not in line with the blade. Kickback could cause the
sa to jump back ards, but kickback forces can be
controlled by the operator, if proper precautions are
taken.
2. When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the
saw motionless in the material until the blade
comes to a complete stop. Ne er attempt to
remo e the saw from the work or pull the saw
backward while the blade is in motion or kickback
may occur. Investigate and take corrective actions to
eliminate the cause of blade binding.
3. When restarting a saw in the workpiece, centre the
saw blade in the kerf so that the saw teeth are not
engaged into the material. If a sa blade binds, it
may alk up or kickback from the orkpiece as the
sa is restarted.
4. Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag
under their o n eight. Supports must be placed
under the panel on both sides, near the line of cut and
near the edge of the panel. (Fig. 3 & 4)
5. Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narro kerf causing excessive friction, blade binding
and kickback.
6. Blade depth and be el adjusting locking le ers
must be tight and secure before making the cut. If
blade adjustment shifts hile cutting, it may cause
binding and kickback.
7. Use extra caution when sawing into existing walls
or other blind areas. The protruding blade may cut
objects that can cause kickback.
8. ALWAYS hold the tool firmly with both hands.
NEVER place your hand, leg or any part of your
body under the tool base or behind the saw,
especially when making cross-cuts. If kickback
occurs, the sa could easily jump back ards over
your hand, leading to serious personal injury. (Fig. 5)
9. Ne er force the saw. Push the saw forward at a
speed so that the blade cuts without slowing.
Forcing the sa can cause uneven cuts, loss of
accuracy, and possible kickback.
Guard function
1. Check the guard for proper closing before each
use. Do not operate the saw if the guard does not
mo e freely and enclose the blade instantly. Ne er
clamp or tie the guard so that the blade is
exposed. If the sa is accidentally dropped, the guard
may be bent. Check to make sure that guard moves
freely and does not touch the blade or any other part,
in all angles and depths of cut.
2. Check the operation and condition of the guard
return spring. If the guard and the spring are not
operating properly, they must be ser iced before
use. The guard may operate sluggishly due to
damaged parts, gummy deposits, or a build-up of
debris.
3. Assure that the base plate of the saw will not shift
while performing a “plunge cut”. Blade shifting
side ays ill cause binding and likely kick back.
4. Always obser e that the guard is co ering the
blade before placing the saw down on bench or
floor. An unprotected, coasting blade ill cause the
sa to alk back ards, cutting hatever is in its path.
Be a are of the time it takes for the blade to stop after
s itch is released.
Additional safety warnings
1. Use extra caution when cutting damp wood,
pressure treated lumber, or wood containing
10
knots. Maintain smooth advancement of tool ithout
decrease in blade speed to avoid overheating the
blade tips and if cutting plastics, to avoid melting the
plastic.
2. Do not attempt to remo e cut material when blade
is mo ing. Wait until blade stops before grasping
cut material. Blades coast after turn off.
3. A oid cutting nails. Inspect for and remo e all
nails from lumber before cutting.
4. Place the wider portion of the saw base on that
part of the workpiece which is solidly supported,
not on the section that will fall off when the cut is
made. If the workpiece is short or small, clamp it
down. DO NOT TRY TO HOLD SHORT PIECES BY
HAND! (Fig. 6)
5. Before setting the tool down after completing a
cut, be sure that the guard has closed and the
blade has come to a complete stop.
6. Ne er attempt to saw with the circular saw held
upside down in a ise. This is extremely
dangerous and can lead to serious accidents.
(Fig. 7)
7. Some material contains chemicals which may be
toxic. Take caution to pre ent dust inhalation and
skin contact. Follow material supplier safety data.
8. Do not stop the blades by lateral pressure on the
saw blade.
9. Do not use any abrasi e wheels.
10. Only use the saw blade with the diameter that is
marked on the tool or specified in the manual. Use
of an incorrectly sized blade may affect the proper
guarding of the blade or guard operation hich could
result in serious personal injury.
11. Keep blade sharp and clean. Gum and ood pitch
hardened on blades slo s sa and increases
potential for kickback. Keep blade clean by first
removing it from tool, then cleaning it ith gum and
pitch remover, hot ater or kerosene. Never use
gasoline.
12. Wear a dust mask and hearing protection when
use the tool.
13. Always use the saw blade intended for cutting the
material that you are going to cut.
14. Only use the saw blades that are marked with a
speed equal or higher than the speed marked on
the tool.
15. (For European countries only)
Always use the blade which conforms to EN847-1.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with
product (gained from repeated use) replace strict
adherence to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
FUNCTIONAL DESCRIPTION
CAUTION:
• Al ays be sure that the tool is s itched off and
unplugged before adjusting or checking function on the
tool.
Adjusting depth of cut (Fig 8)
CAUTION:
• After adjusting the depth of cut, al ays tighten the
clamping scre securely.
Loosen the clamping scre on the depth guide and move
the blade lo er limit stopper to the desired depth on the
scale plate. At the desired depth of cut, tighten the
clamping scre firmly.
For cleaner, safer cuts, set cut depth so that no more than
one blade tooth projects belo orkpiece. Using proper
cut depth helps to reduce potential for dangerous
KICKBACKS hich can cause personal injury.
NOTE:
• Setting the blade lo er limit stopper to the desired
depth on the scale plate allo s rough depth of cut. For
accurate depth of cut, measure the actual protrusion of
sa blade belo the tool base.
Quick stop button for 2 to 3 mm depth of
cut when using guide rail (accessory)
(Fig 9)
This tool has the quick stop button for 2 to 3 mm depth of
cut on the gear housing aside the rear handle hen using
guide rail. This is used hen avoiding splinter on the
orkpiece in the cut. Make a pass of the 2 to 3 mm first
cut and then make another pass of usual cut.
To obtain the 2 to 3 mm depth of cut, push in the stop
button to ard the sa blade. This is convenient for
avoiding splinter on the orkpiece.
To release the depth of cut from this position for free depth
of cut, just pull the button back. (Fig. 10)
Bevel cutting (Fig 11)
Tilting to the right (Fig. 12)
Turn the positive stopper so that the arro on it points one
of t o positions (vertical for 22.5°, horizontal for 45°).
Loosen the clamping scre s in front and back. Then, tilt
the tool base until it stops and secure the base ith the
clamping scre s.
To get 48° bevel angle, move the lever to 48° marking as
far as it ill go. Turn the positive stopper so that the arro
on it points to the horizontal position. Then, tilt the tool
base until it stops and secure the base ith the clamping
scre s. (Fig. 13)
Tilting to the left (Fig. 14)
The tool can be tilted to the left 1° bevel angle. To get the
left 1° bevel angle, loosen the clamping scre s in front
and back, tilt the tool handle slightly to the right and push
t o bevel angle shifting levers at the same time in the
direction of arro hich has a marking -1. And then tilt the
tool handle to the left hile pushing these t o levers at
the same time. Secure the base ith the clamping scre s.
NOTE:
• Returning the blade to the right angle makes the
shifting lever return to 0° by itself.
Other manuals for SP6000
18
Table of contents
Languages:
Other Makita Saw manuals
Makita
Makita UC3520A User manual
Makita
Makita M4302 User manual
Makita
Makita LF1000 User manual
Makita
Makita LH1040 User manual
Makita
Makita JR3030 User manual
Makita
Makita JR3061T User manual
Makita
Makita LS1040 User manual
Makita
Makita BPB180 User manual
Makita
Makita 5402NA Quick start guide
Makita
Makita 2414B User manual
Makita
Makita M4500 User manual
Makita
Makita XRJ02 User manual
Makita
Makita 2702 Manual
Makita
Makita DLS714 User manual
Makita
Makita LS800D User manual
Makita
Makita XPS02 User manual
Makita
Makita 2414NB User manual
Makita
Makita LS1040F User manual
Makita
Makita HS012G User manual
Makita
Makita DSD180 User manual
