Makita DRS780 User manual

DRS780

EN Cordless Rear Handle Saw INSTRUCTION MANUAL 7

SL Brezžična žaga s stranskim

ročajem NAVODILA ZA UPORABO 15

SQ Sharrë me dorezë të pasme

me bateri MANUALI I PËRDORIMIT 23

BG Акумулаторен циркулярен

трион със задна дръжка РЪКОВОДСТВО ЗА

ЕКСПЛОАТАЦИЯ 32

HR Bežična pila sa stražnjom

ručkom PRIRUČNIK S UPUTAMA 42

МК Безжична пила со задна

рачка УПАТСТВО ЗА УПОТРЕБА 50

SR Бежична тестера са задњом

ручком УПУТСТВО ЗА УПОТРЕБУ 59

RO Ferăstrău cu mâner posterior

cu acumulator MANUAL DE INSTRUCŢIUNI 68

UK Бездротова пила з задньою

ручкою ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 77

RU Аккумуляторная дисковая

пила РУКОВОДСТВО ПО

ЭКСПЛУАТАЦИИ 86

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

15.88

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

7ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: DRS780

Blade diameter 185 mm

Max. Cutting depth at 0° 65 mm

at 45° bevel 45 mm

at 53° bevel 38 mm

No load speed 5,100 min-1

Overall length 446 mm

Rated voltage D.C. 36 V

Net weight 5.0 - 5.7 kg

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydifferfromcountrytocountry.

• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Batterycartridge BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /

BL1840B / BL1850 / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof

residence.

WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges

andchargersmaycauseinjuryand/orre.

Intended use

Thetoolisintendedforperforminglengthwaysand

crosswaysstraightcutsandmitrecutswithanglesin

woodwhileinrmcontactwiththeworkpiece.

Noise

ThetypicalA-weightednoiseleveldeterminedaccord-

ing to EN62841-2-5:

Soundpressurelevel(LpA):92dB(A)

Soundpowerlevel(LWA):103dB(A)

Uncertainty(K):3dB(A)

NOTE:Thedeclarednoiseemissionvalue(s)has

been measured in accordance with a standard test

methodandmaybeusedforcomparingonetoolwith

another.

NOTE:Thedeclarednoiseemissionvalue(s)

mayalsobeusedinapreliminaryassessmentof

exposure.

WARNING: Wear ear protection.

WARNING: The noise emission during actual

use of the power tool can differ from the declared

value(s) depending on the ways in which the

tool is used especially what kind of workpiece is

processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

off and when it is running idle in addition to the

trigger time).

Vibration

Thevibrationtotalvalue(tri-axialvectorsum)deter-

mined according to EN62841-2-5:

Work mode: cutting wood

Vibrationemission(ah,W):2.5m/s2or less

Uncertainty(K):1.5m/s2

NOTE:Thedeclaredvibrationtotalvalue(s)hasbeen

measured in accordance with a standard test method

andmaybeusedforcomparingonetoolwithanother.

NOTE:Thedeclaredvibrationtotalvalue(s)mayalso

beusedinapreliminaryassessmentofexposure.

8ENGLISH

WARNING:

The vibration emission during actual

use of the power tool can differ from the declared val-

ue(s) depending on the ways in which the tool is used

especially what kind of workpiece is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

off and when it is running idle in addition to the

trigger time).

EC Declaration of Conformity

For European countries only

TheECdeclarationofconformityisincludedasAnnexA

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm"powertool"inthewarningsreferstoyour

mains-operated(corded)powertoolorbattery-operated

(cordless)powertool.

Cordless circular saw safety warnings

Cutting procedures

1. DANGER: Keep hands away from cutting

area and the blade. Keep your second hand

on auxiliary handle, or motor housing. If both

handsareholdingthesaw,theycannotbecutby

the blade.

2. Do not reach underneath the workpiece. The

guardcannotprotectyoufromthebladebelowthe

workpiece.

3. Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the blade

teeth should be visible below the workpiece.

4. Never hold the workpiece in your hands or

across your leg while cutting. Secure the

workpiece to a stable platform. It is important to

supporttheworkproperlytominimisebodyexpo-

sure, blade binding, or loss of control.

►Fig.1

5. Hold the power tool by insulated gripping

surfaces, when performing an operation where

the cutting tool may contact hidden wiring.

Contact with a “live” wire will also make exposed

metal parts of the power tool “live” and could give

the operator an electric shock.

6. When ripping, always use a rip fence or

straight edge guide.Thisimprovestheaccuracy

of cut and reduces the chance of blade binding.

7. Always use blades with correct size and shape

(diamond versus round) of arbour holes.

Blades that do not match the mounting hardware

of the saw will run off-centre, causing loss of

control.

8. Never use damaged or incorrect blade wash-

ers or bolt. The blade washers and bolt were

speciallydesignedforyoursaw,foroptimum

performanceandsafetyofoperation.

Kickback causes and related warnings

— kickback is a sudden reaction to a pinched,

jammedormisalignedsawblade,causingan

uncontrolled saw to lift up and out of the workpiece

toward the operator;

— whenthebladeispinchedorjammedtightlybythe

kerf closing down, the blade stalls and the motor

reactiondrivestheunitrapidlybacktowardthe

operator;

— if the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade

toclimboutofthekerfandjumpbacktowardthe

operator.

Kickbackistheresultofsawmisuseand/orincorrect

operating procedures or conditions and can be avoided

bytakingproperprecautionsasgivenbelow.

1. Maintain a rm grip with both hands on the

saw and position your arms to resist kickback

forces. Position your body to either side of the

blade, but not in line with the blade.Kickback

couldcausethesawtojumpbackwards,but

kickbackforcescanbecontrolledbytheoperator,

if proper precautions are taken.

When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold

the saw motionless in the material until the

blade comes to a complete stop. Never attempt

to remove the saw from the work or pull the

saw backward while the blade is in motion or

kickback may occur. Investigate and take correc-

tive actions to eliminate the cause of blade binding.

3. When restarting a saw in the workpiece, centre

the saw blade in the kerf so that the saw teeth

are not engaged into the material. If a saw blade

binds,itmaywalkuporkickbackfromthework-

piece as the saw is restarted.

4. Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend

to sag under their own weight. Supports must be

placed under the panel on both sides, near the line

of cut and near the edge of the panel.

►Fig.2

►Fig.3

5. Do not use dull or damaged blades.

Unsharpenedorimproperlysetbladesproduce

narrow kerf causing excessive friction, blade

binding and kickback.

6. Blade depth and bevel adjusting locking levers

must be tight and secure before making the

cut.Ifbladeadjustmentshiftswhilecutting,itmay

cause binding and kickback.

9ENGLISH

7. Use extra caution when sawing into existing

walls or other blind areas. The protruding blade

maycutobjectsthatcancausekickback.

8. ALWAYS hold the tool rmly with both hands.

NEVER place your hand, leg or any part of your

body under the tool base or behind the saw,

especially when making cross-cuts. If kickback

occurs,thesawcouldeasilyjumpbackwardsover

yourhand,leadingtoseriouspersonalinjury.

►Fig.4

9. Never force the saw. Push the saw forward at a

speed so that the blade cuts without slowing.

Forcing the saw can cause uneven cuts, loss of

accuracy,andpossiblekickback.

Lower guard function

1. Check the lower guard for proper closing

before each use. Do not operate the saw if the

lower guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position.Ifthesawisaccidentally

dropped,thelowerguardmaybebent.Raisethe

lower guard with the retracting handle and make

sureitmovesfreelyanddoesnottouchtheblade

oranyotherpart,inallanglesanddepthsofcut.

Check the operation of the lower guard spring. If

the guard and the spring are not operating prop-

erly, they must be serviced before use. Lower

guardmayoperatesluggishlyduetodamaged

parts,gummydeposits,orabuild-upofdebris.

3. The lower guard may be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts”. Raise the lower guard

by the retracting handle and as soon as the

blade enters the material, the lower guard

must be released. For all other sawing, the lower

guardshouldoperateautomatically.

4. Always observe that the lower guard is cover-

ing the blade before placing the saw down on

bench or oor. An unprotected, coasting blade

will cause the saw to walk backwards, cutting

whatever is in its path. Be aware of the time it

takes for the blade to stop after switch is released.

5. To check lower guard, open lower guard by

hand, then release and watch guard closure.

Also check to see that retracting handle does

not touch tool housing. Leaving blade exposed

is VERY DANGEROUS and can lead to serious

personalinjury.

Additional safety warnings

Use extra caution when cutting damp wood, pres-

sure treated lumber, or wood containing knots.

Maintain smooth advancement of tool without decrease

in blade speed to avoid overheating the blade tips.

2. Do not attempt to remove cut material when

blade is moving. Wait until blade stops before

grasping cut material. Blades coast after turn off.

3. Avoid cutting nails. Inspect for and remove all

nails from lumber before cutting.

4. Place the wider portion of the saw base on

that part of the workpiece which is solidly

supported, not on the section that will fall off

when the cut is made. If the workpiece is short

or small, clamp it down. DO NOT TRY TO HOLD

SHORT PIECES BY HAND!

►Fig.5

5. Before setting the tool down after completing a

cut, be sure that the guard has closed and the

blade has come to a complete stop.

6. Never attempt to saw with the circular saw

held upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

►Fig.6

7. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

8. Do not stop the blades by lateral pressure on

the saw blade.

9. Do not use any abrasive wheels.

10. Only use the saw blade with the diameter that

is marked on the tool or specied in the man-

ual.Useofanincorrectlysizedblademayaffect

the proper guarding of the blade or guard opera-

tionwhichcouldresultinseriouspersonalinjury.

11. Keep blade sharp and clean. Gum and wood

pitch hardened on blades slows saw and

increasespotentialforkickback.Keepbladeclean

byrstremovingitfromtool,thencleaningitwith

gum and pitch remover, hot water or kerosene.

Never use gasoline.

12. Wear a dust mask and hearing protection when

use the tool.

13. Always use the saw blade intended for cutting

the material that you are going to cut.

14. Only use the saw blades that are marked with

a speed equal or higher than the speed marked

on the tool.

15. (For European countries only)

Always use the blade which conforms to

EN847-1.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

10 ENGLISH

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

Forcommercialtransportse.g.bythirdparties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

inganexpertforhazardousmaterialisrequired.

Pleasealsoobservepossiblymoredetailed

national regulations.

Tape or mask off open contacts and pack up the

batteryinsuchamannerthatitcannotmove

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

siveheat,explosion,orleakofelectrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

havebeenaltered,mayresultinthebatterybursting

causingres,personalinjuryanddamage.Itwill

alsovoidtheMakitawarrantyfortheMakitatooland

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

CAUTION: Always bring down the base when

installing/removing the batteries. Be careful not to

pinch your ngers.

CAUTION: Do not use the battery adapter with

the circular saw. The cable of the battery adapter

may hinder the operation and result in personal

injury.

►Fig.7: 1. Lever 2. Hook 3. Red indicator 4. Button

5.Batterycartridge

Beforeremovingthebatterycartridge,liftthehookup

andloosentheleverfordepthadjustmenttolowerthe

toolbase.Thenslidethebatteryfromthetoolwhile

sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoronthe

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

youorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

NOTE:Thetooldoesnotworkwithonlyonebattery

cartridge.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placed under one of the following conditions.

Other manuals for DRS780

This manual suits for next models

Table of contents

Languages:

Popular Saw manuals by other brands

RIDGID

RIDGID BS1400 owner's manual

ATIKA

ATIKA BWS 400-2 Original instructions

RGC

RGC FS20 instructions

IMET Spa

IMET Spa BASIC 300 PLUS SHI Instructions for use

IMET Spa

IMET Spa SIRIO 370 AF-E User instructions

Optimum

Optimum OPTisaw CS 275 operating manual

Stihl

Stihl MS 462 C-M instruction manual

AEG

AEG TS 250 K Original instructions

Meec tools

Meec tools 004665 operating instructions

Ryobi

Ryobi RCS1400 Original instructions

DeWalt

DeWalt DCS391 instruction manual

Sealey

Sealey SA72 instructions

skilsaw

skilsaw SPT88 Operating/safety instructions

Urrea

Urrea SI810 User manual and warranty

EINHELL

EINHELL BKG 210/1 operating instructions

Altrad

Altrad BELLE RANGER 450 Operator's manual

Porter-Cable

Porter-Cable 725 instruction manual

Rockwell

Rockwell RK7241S manual