Makita 9207SPC User manual

Electronic Sander Polisher

Noloadspeed

1,500

2,800

R/min.

180

(7")

MODEL

9207SPC

Overall length Net weight Spindle thread

470mm

(18-1/2")

3.5

(7.7 Ibs)

5/8-11

UNC

INSTRUCTION MANUAL

DOUBLE

INSULATION

SPEC1

FICATIONS

IMPORTANT

SAFETY

INSTRUCTIONS

(For

All

Tools)

WARNING:

WHEN USINGELECTRICTOOLS, BASICSAFETY

PRECAUTIONS SHOULD ALWAYS BE FOLLOWEDTO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL

INJURY, INCLUDING THE FOLLOWING:

READ

ALL

INSTRUCTIONS.

-1.

IO.

11.

12.

13.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

CONSIDER WORK AREA ENVIRONMENT. Don't use power tools

damp

or wet locations. Keep work area well

lit.

Don't expose power tools torain.

Don't use tool

presence of flammable liquids or gases.

KEEP CHILDREN AWAY. All visitors should be kept away from work area.

Don't let visitors contact tool or extension cord.

STORE IDLETOOLS. When not

use, toolsshould be stored

dry, and high

or locked-up place

out of reach of children.

DON'T FORCE TOOL.

willdo the

job

betterandsafer at theratefor which

was intended.

USE RIGHT TOOL. Don't force small tool or attachment to do the job of a

heavy-duty tool. Don't use tool for purpose not intended.

DRESS PROPERLY. Don't wear loose clothing orjewelry. They can be caught

in moving parts. Rubber gloves and non-skid footwear are recommended

when working outdoors. Wear protective hair covering tocontain long hair.

USE SAFETY GLASSES. Also use face or dust mask if cutting operation is

dusty.

DON'T ABUSE CORD. Never carry tool by cord or yank

todisconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

SECURE WORK. Use clamps or a vise to hold work. It's safer than using

your hand and

frees both hands to operate tool.

DON'T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and

safer performance. Follow instructions for lubricatingand changing acces-

sories. Inspect toolcords periodicallyand if damaged, have repaired byautho-

rized service facility. Inspect extension cords periodically and replace if

damaged. Keep handles dry, clean, and free from oil and grease.

DISCONNECTTOOLS. When not in use, beforeservicing, and when chang-

ing accessories, such as blades, bits, cutters.

Ampere Rating

More Not More

Than Than

100 101

150

AWG

18 16 14

16 16 14 12

14 12

Not Recommended

18 16

21. REPLACEMENT PARTS. When servicing, useonly identicalreplacementparts.

22. POLARIZEDPLUGS. To reduce the risk of electric shock, this equipment has

a polarized plug (one blade is wider than the other). This plug will

fit

polarized outlet only one way. If the plug does not

fit

fully in the outlet,

reversethe plug.

stilldoes not

fit,

contactaqualifiedelectriciantoinstall

the proper outlet.

not change the

plug

any way.

VOLTAGE WARNING:

Before connecting the tooltoa power source (receptacle,

outlet, etc.) be sure the voltage supplied is the same as that specified on the

nameplate of the tool.

power source withvoltage greater than that specified

for the tool can result

SERIOUS

INJURY

tothe user

as well as damage to

the tool. If

doubt,

NOT PLUG

THE TOOL.

Using a power source

with

voltage less than the nameplate rating is harmful to the motor.

SAVE

THESE

INSTRUCTIONS.

PRECAUTION IN

USE

not

use

with D.C. application.

HOW

USE

Switch action

To start the tool, simply pull the trigger.

Release

the trigger to stop. For continuous

operation without having to keep your

finger on the tirgger, just pull the trigger

and then push in the lock button with

your thumb. To stop the tool from the

lock position, simply pull the trigger again

and release

it.

Speed

changes

the knob on the switch lever in front

turned tothe "H" setting, the high speed

obtained; if

set

tothe

"L"

setting, the low

speed results. Use the suitable speed setting

in order to obtain the

best

performance

finish.

iighspeed

For disc sanding

.ow speed

. .

For polishing

ani

Fig.

Trigger switch

Speed change

knc

Arrow

indication

ig.2

Knobsetting

terms

speed

The tool speed can

set

for anywherefrom 1,500 to

2,800

rpm.Simply align any knob

numbered setting with the arrow indicator. Consult chart below for approximate

speeds

obtained for each of the numbered settings.

You can also obtainspeeds other than the settings by adjusting the knob in between.

For example, for 2,150 rpm, align

that arrow will be pointed halfway between the

numbers

and

CAUTION

Numbered Setting

The knob for speed settings can be turned

only

far

and back to

Do not force

the knob

past

the

speed

change func-

tion may no longer work. 2000

2300

5 2550

2800

CAUTION

ALWAYS SWITCH OFF AND UNPLUG THE TOOL

BEFORE

INSTALLING

RE-

MOVINGA SANDING DISC

WOOL BONNET.

CAUTIONS

Always wear safety

glasses

and mask during operation.

Gripthe tool firmly with both hands.

nottouch the rotating abrasive disc.

When sanding metal surfaces, be careful of the flying sparks. Handletool interms

the direction they fly.

FOR

USE

SANDER

For disc sanding, assemble tool

seen

right.

Hold

the spindle firmly with the wrench.

Put on the rubber pad and

all,

then tighten

lock nut usingthe lock nut wrench, turning

clockwise.

Make certain the rubber pad tightening nut

not loose.

Operation

When applyingsander towork surface, keep

the angle

10 to

degrees and use gentle

pressure only.

Abrasive

diJc

Fig.

ock

nut

wrench

Fig.

FOR

USE

POLISHER

For

polishing operation, assemble the

tool

right. Hold the spindle firmly with

the wrench

17.

Put

the rubber pad, then

tighten lock nut using the lock nut wrench

provided, turning clockwise. Next, put

wool bonnet on, fastening

securely with

strings

snugly

possible,

near the center.

Tuck

the

loose ends of

the

cord

be-

tween the wool bonnet and the rubber pad.

CAI

ITlnN:

Fig.

.-.

.-...

Loose cord ends when using the wool

bonnet can be very dangerous. Always tuck

them safety in out of the way.

Lock

nut

wrench

Fig.

Operation

When polishing, keep the angle

about

degrees

and

work gently

the direction

the polisher

turning.

Fig.

MAINTENANCE

CAUTION

Always be sure that the tool

switchedoff and unpluggedbefore attempting to perform

inspectionand maintenance.

Replacingcarbon brushes

Remove and check the carbon brushes

regularly. Replace when they wear down

to the limit mark. Keep the carbon

brushes clean and free to slip in the

holders. Both carbon brushes should be

replaced

the same time. Use only iden-

tical

carbon brushes.

Limit mark

Fig.

ACCESSORIES

CAUTION:

The accessories specified in this manual are recommended for use with your Makita

Electronic Sander Polisher. The use

any

other accessories

might

hazardous.

100

120

Wool

bonnet

180

(Part

No.

743404-0)

742067-9

742068-7

742069-5

742089-9 10

742070-0

742071-8

742090-4

742091-2

Lock nut wrench

(Part

No.

782413-4)

Abrasive disc

Grit

Part

No.

Discs

Der

oka

Lock nut

(Part

No.

224517

Wrench

(Part

No.

781008-0)

Rubber

pad

170

(Part

No.

743012-7)

180

(7")

ELECTRONIC SANDER POLISHER

Model

9207SPC

Note: The switch, noise suppressor and other part configurations

may differ from country to country.

Table of contents

Popular Sander manuals by other brands

Oliver

Oliver 6305 owner's manual

Jet

Jet 22-44 Pro-3 Operating instructions and parts manual

Craftsman

Craftsman 351.215131 Operator's manual

Clarke

Clarke Woodworker CBS1-5B Operation & maintenance instructions

Chicago Pneumatic

Chicago Pneumatic CP9778 Operator's manual

Nitto Kohki

Nitto Kohki BB-20 instruction manual

Ferm

Ferm FEOS-135 user manual

Unior

Unior 1510 Operating instruction

stayer

stayer ls1200 operating instructions

Jet

Jet JSG-96 Operating instructions and parts manual

Parkside

Parkside PDS 290 B2 Operation and safety notes

Status

Status XPA Series Original instructions

Clarke

Clarke EZ Sand Operator's manual

Craftsman

Craftsman 113.22521 owner's manual

Craftsman

Craftsman 113.225831 owner's manual

CLAS

CLAS OP 1429 manual

Parkside

Parkside PEXS 270 Al user guide

Flex

Flex ST 1005 VE operating instructions