Makita 9000BL User manual

I-

load speed

IRPMl

6,000

Overall length Net weight Spindle thread

518

UNC

450

7-314")

5.5

(12.1

Ibs)

Sander

MODEL

9000BL

INSTRUCTION MANUAL

DOUBLE

INSULATION

SPECIFICATIONS

Manufacturer reserves the right to change specificattons without notice.

Note Specifications may differ from country to country.

Get other manuals https://www.bkmanuals.com

IMPORTANT

SAFETY INSTRUCTIONS

(For

All Tools)

WARNING:

WHEN USING ELECTRIC TOOLS, BASIC SAFE-

REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER-

TY PRECAUTIONS SHOULD ALWAYS

FOLLOWED TO

SONAL INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

CONSIDER WORK AREA ENVIRONMENT. Don't use power tools

damp

wet locations. Keep work area well

lit.

Don't expose power tools to rain.

Don't use tool

presence of flammable liquids or gases.

KEEP CHILDRENAWAY. All visitors should be kept away from work area.

Don't let visitors contact tool or extension cord.

STORE IDLETOOLS. When not

use, tools should bestored

dry, andhigh

or locked-up place

out of reach of children.

DON'T FORCETOOL.

willdothejob better and safer attheratefor which

was intended.

USE RIGHT TOOL. Don't force small tool

attachment to do the job of a

heavy-duty tool. Don't use tool for purpose not intended.

DRESS PROPERLY. Don't wear looseclothing orjewelry. They can becaught

in moving parts. Rubber gloves and non-skid footwear are recommended

whenworking outdoors. Wear protective hair covering tocontain long hair.

USE SAFETY GLASSES. Also use face or dust mask if cutting operation is

dusty.

DON'T ABUSE CORD. Never carry tool by cord or yank

todisconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

IO.

SECURE WORK. Use clamps

a vise to hold work. It's safer than using

your hand and

frees both hands to operate tool.

11.

DON'T OVERREACH. Keep proper footing and balance at all times.

12.

MAINTAIN TOOLS WITH CARE. Keeptools sharp and clean for better and

safer performance. Follow instructions for lubricating and changing acces-

sories. Inspecttoolcords periodicallyandifdamaged, have repairedbyautho-

rized service facility. Inspect extension cords periodically and replace if

damaged. Keep handles dry, clean, and free from

oil

and grease.

13.

DISCONNECTTOOLS. Whennot

use, beforeservicing, and when chang-

ing accessories, such

blades, bits, cutters.

Get other manuals https://www.bkmanuals.com

14.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to

seethat keysandadjusting wrenches are removed fromtool before turning

on.

15.

AVOID UNINTENTIONALSTARTING. Don't carry plugged-intool

with

finger

on switch.

sure switch is OFF when plugging

in.

16.

OUTDOOR USEEXTENSIONCORDS. Whentoolis usedoutdoors, use only

extension cords intended for use outdoors and

marked.

tool

when you are tired.

18.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other

part that is damaged should be carefully checked to determine that

will

operate properly and performitsintended function. Check for alignment of

movingparts, bindingof movingparts, breakageof parts, mounting, and any

other conditions that may affect its operation.

guard or other part that

is damaged should be properly repaired or replaced by an authorized serv-

ice center unless otherwise indicatedelsewhere inthis instruction manual.

Have defective switches replaced by authorized service center. Don't use

tool

switch does not turn

on and off.

19.

GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded

surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

20.

REPLACEMENTPARTS.When servicing, useonly identicalreplacementparts.

17.

STAY ALERT. Watch what

you

are

doing,

use

commonsense. Don't operate

VOLTAGE WARNING: Before connectingthe tooltoa power source (receptacle,

outlet, etc.) be sure the voltage supplied is the same as that specified on the

nameplate of the tool. A power source withvoltage greater than that specified

for the tool can result inSERIOUS INJURY to the user

as well as damage to

the tool. If indoubt, DO NOT PLUG IN THE TOOL. Using a power source with

voltage less than the nameplate rating is harmful to the motor.

Get other manuals https://www.bkmanuals.com

ADDITIONAL SAFETY RULES FOR SANDER

Check the backing pad carefully for cracks, damage or deformity before

Hold the tool firmly.

Keep hands away from rotating parts.

Make sure abrasive disc is not contacting the workpiece before the switch

Do not leave the tool running. Operate the tool only when hand-held.

Donottouchthe workpiece immediately after operation:

may beextremely

operation. Replace cracked, damaged or deformed pad immediately.

is turned on.

hot and could burn your skin.

ADDITIONAL SAFETY RULES FOR GRINDER

Keep guards

place.

Useonly wheels havingamaximumoperatingspeedatleastas highas

“No

Load

RPM”

marked onthe tool’s nameplate.When usingdepressedcenter

wheels, be sure to use only fiberglass-reinforced wheels.

Check the wheel carefully for cracks or damage before operation. Replace

cracked or damaged wheel immediately.

Use only flanges specified for this tool.

Be careful not to damage the spindle, the flange (especially the installing

surface) or the lock nut. Damage to these parts could result

wheel

breakage.

Hold the tool firmly.

Keep hands away from rotating parts.

Make sure the wheel is not contacting the workpiece beforethe switch is

turned on.

Before using the tool on an actual workpiece, let

run for a while. Watch

for vibration or wobbling that could indicate poor installation or a poorly

balanced wheel.

IO.

Use the specified surface of the wheel to perform the grinding.

11.

Watch out for flying sparks. Holdthe tool

that sparks fly away from you

12.

Do not leave the tool running. Operate the tool only when hand-held.

13.

Donottouchthe workpiece immediately afteroperation:

may beextremely

and other persons or flammable materials.

hot and could burn your skin.

SAVE

THESE

INSTRUCTIONS.

Get other manuals https://www.bkmanuals.com

Installingside grip (auxiliary handle)

Screw the

side

grip on the tool securely.

The

side

grip can be installed oneither

side

the tool, whichever

convenient.

Installingor removing abrasive

disc

CAUTION

Always be sure that the tool

switched

off

and unpluggedbefore installing or removing

the disc.

NOTE

Use sander accessoriesspecified in this manual. These must be purchased

separate.

Mount the rubber pad onto the spindle. Fit

the disc on over the rubber pad and screw

the lock nutonto the spindle.

Abrasive

disc

removethe disc,

the installation procedure in reverse

Get other manuals https://www.bkmanuals.com

Switchaction

start the tool, simply pull the trigger.

Release

the trigger to stop. Forcontinuous

operation, pull the trigger and then push in

the lock button.

stopthe tool from the

locked position, pull the trigger fully, then

release

it.

CAUTION

Before plugging in the tool, always check to

see

that the trigger switch actuates properly

and returnsto the

"OFF"

positionwhen released.

Operation

Hold the tool firmly. Turn the tool on and

then apply the abrasive disc to the work-

piece. Ingeneral, keep the abrasive disc

an angle of about

15'

to the workpiece

surface. Apply slight pressure only. Exces-

sive

pressure will result in poor perform-

ance and premature wear to the abrasive

disc.

Get other manuals https://www.bkmanuals.com

USED

GRINDER

NOTE:

Use grinder accessories specified inthis manual.These must be purchasedby separate.

WARNING:

Always use guard assembly or accessory kit, noted below, for type 27 depressed center

wheel.

Guardassembly Guardaccessory kit

Part

No.

191214-3.

. .

For 180mm

(7")

Part No. 191215-1

. .

For 230 mm (9") Part No. 191228-2

. .

For 180mm

(7")

Part No. 191231-3

For 230 mm (9")

Installingor removingdepressed center wheel

CAUTION

Always be sure that the tool

switched off and unplugged beforeinstallingor removing

the wheel.

Mount the inner flange onto the spindle.

Fit

the wheel on over the inner flange and

screw the lock nut onto the spindle.

Inner

flange

tighten the lock nut, press the shaft

lock firmly

that the spindle cannot re-

volve, then use the lock nut wrench and

securely tightenclockwise.

To remove the wheel, follow the installationprocedure in reverse.

Get other manuals https://www.bkmanuals.com

Operation

Hold the tool firmly. Turn the tool on and

then apply the wheel or disc to the work-

piece.

In general, keep the edge of the wheel or

disc

an angle of about 15" to the work-

piecesurface.

During the break-in period with

new

wheel, do not work the grinder in the

direction or

will cut into theworkpiece.

Once the edge of the wheel has been

rounded off by use, the wheel may be

worked inboth A and

directions.

WARNING:

should never be necessary to force

the

tool. The weight of the tool applies adequate

pressure. Forcingand excessive pressurecouldcause dangerouswheel breakage.

Continued use of

worn-out wheel may result in wheel explosionand serious personal

injury. Depressed center wheel should not be used after

has been worn down to

5 mm (4-1/2") in diameter. Use of the wheel after this point

unsafe and

should

be removedfrom service and rendered unusable by intentional destruction.

Get other manuals https://www.bkmanuals.com

MAINTENANCE

CAUTION

Always be sure that the tool

switched off and unpluggedbefore attempting toperform

inspectionor maintenance.

Replacing carbon brushes

Remove and check the carbon brushes

regularly. Replace when they wear down

to the limitmark. Keep the carbon brushes

clean and free to slip in the holders. Both

carbon brushes should be replaced

the

Limit

mark

same time. Use only identical carbon

brushes.

Use

screwdriver to remove the brush

holder caps. Take out the worn carbon

brushes, insert the new ones and secure

the brush holder caps.

maintain product SAFETY and RELIABILITY, repairs, any other maintenance or

adjustment should be performed by Makita Authorized

Factory Service Centers,

always using Makitareplacementparts.

Get other manuals https://www.bkmanuals.com

ACCESSORIES

CAUTION

These accessories or attachments are recommended for use with your Makita tool specified in this

manual. The

use

any other accessories or attachments might present

risk of injury to persons. The

accessories or attachments should

used only in the proper and intended manner.

Part

No.

Rubber pad

170 mm (6-3/4")

Part No. 743012-7

Sme

Abrasive

disc

(5per pkg)

742071-A-5

Guard assembly

Inner flange

(fordepressedcenter wheel)

Part

NO. 224111-9

Part

No.

Diameter 1")

742067-A-5

742069-A-5

742089-A-

742070-A-5

180 (7")

Lock

nut48

(for abrasive discs)

Part No. 224517-1

Get other manuals https://www.bkmanuals.com

Table of contents

Popular Sander manuals by other brands

Oliver

Oliver 6305 owner's manual

Jet

Jet 22-44 Pro-3 Operating instructions and parts manual

Craftsman

Craftsman 351.215131 Operator's manual

Clarke

Clarke Woodworker CBS1-5B Operation & maintenance instructions

Chicago Pneumatic

Chicago Pneumatic CP9778 Operator's manual

Nitto Kohki

Nitto Kohki BB-20 instruction manual

Ferm

Ferm FEOS-135 user manual

Unior

Unior 1510 Operating instruction

stayer

stayer ls1200 operating instructions

Jet

Jet JSG-96 Operating instructions and parts manual

Parkside

Parkside PDS 290 B2 Operation and safety notes

Status

Status XPA Series Original instructions

Clarke

Clarke EZ Sand Operator's manual

Craftsman

Craftsman 113.22521 owner's manual

Craftsman

Craftsman 113.225831 owner's manual

CLAS

CLAS OP 1429 manual

Parkside

Parkside PEXS 270 Al user guide

Flex

Flex ST 1005 VE operating instructions