Makita 68OODBV User manual

Drywall

Screwdriver

MODEL

68OODBV

6801DBV

MODEL 6800DBV

MODEL 680lDBV

Bit shank

load speed Overall Net

size

(RPM)

length weight

114” Hex

2,500

’?fl!?y

(i:zi:)

114” Hex

4,000 ’::,my

(i;z&

Capacities

Drywall screws No. 6

Self drilling screw

...

(3116“)

INSTRUCTION MANUAL

DOUBLE

NSU

LATl

SPEC

CAT1

Manufacturer reserves the right to change specifications without notice.

Note: Specifications may differ from country to country.

WARNING: For your personal safety, READ and UNDERSTAND before using.

SAVE THESE INSTRUCTIONS

FOR

FUTURE REFERENCE.

IMPORTANT

SAFETY INSTRUCTIONS

(For

All

Tools)

WARNING:

WHEN USINGELECTRICTOOLS, BASIC SAFETY

PRECAUTIONSSHOULD ALWAYS BE FOLLOWEDTO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL

INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

IO.

11.

12.

13.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp

or wet locations. Keep work area well

lit.

Don't expose power tools to rain.

Don't use tool

presence of flammable liquids or gases.

KEEP CHILDREN AWAY.

All

visitors should be kept away from work area.

Don't let visitors contact tool or extension cord.

STORE IDLETOOLS. When not

use, tools should bestored

dry, and

high

or locked-up place

out of reach of children.

DON'T FORCETOOL.

will do thejob better and safer at the ratefor which

was intended.

USE RIGHT TOOL. Don't force small tool or attachment to do the job of a

heavy-duty tool. Don't usetool for purpose not intended; for example, don't

use circular saw for cutting tree limbs or logs.

DRESS PROPERLY. Don't wear loose clothingorjewelry. They canbecaught

in moving parts. Rubber gloves and non-skid footwear are recommended

when working outdoors. Wear protective hair coveringto contain long hair.

USE SAFETY GLASSES. Also use face or dust mask

cutting operation is

dusty.

DON'T ABUSE CORD. Never carry tool by cordor yank

todisconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

SECURE WORK. Use clamps or a vise to hold work. It's safer than using

your hand and

frees both hands to operate tool.

DON'T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and

safer performance. Follow instructions for lubricating and changing acces-

sories. Inspect toolcords periodicallyand

damaged, haverepairedbyautho-

rized service facility. Inspect extension cords periodically and replace

damaged. Keep handles dry, clean, and free from oil and grease.

DISCONNECTTOOLS. When not

use, beforeservicing, and when chang-

ing accessories, such as blades, bits, cutters.

14.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to

see that keysand adjusting wrenches are removedfromtool beforeturning

on.

15.

AVOID UNINTENTIONALSTARTING. Don't carry tool withfinger onswitch.

Be sure switch is OFF when plugging

in.

16. EXTENSIONCORDS. Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry

the current

your

product

will

draw. An undersized cord will cause a drop

line voltage resulting

loss

of power and overheating. Table

showsthe

correct size touse depending oncord lengthand nameplateampere rating.

If in doubt, use the next heavier gage. The smaller the gage number, the

heavier the cord.

TABLE

MINIMUM

GAGE

FOR

CORD

SETS

Total Length

Cord in Feet

0-25

100

101

150

16 14

16 16 14 12

14 12

Not Recommended

Ampere Rating

More Not More

Than Than AWG

VOLTAGE WARNING: Before connectingthe tool toa power source (receptacle,

outlet, etc.) be sure the voltage supplied is the same as that specified on the

nameplate of the tool. A power source with voltage greater than that specified

for the tool can result

SERIOUS INJURYtothe user

as well as damage to

the tool. If

doubt,

NOT PLUG INTHE TOOL. Using a power source with

voltage less than the nameplate rating is harmful to the motor.

SAVE THESE INSTRUCTIONS.

ADDITIONAL SAFETY RULES

Always be sure you have a firm footing.

Hold the tool firmly.

Keep hands away from rotating parts.

When driving into walls, floors or wherever ”live” electrical wires may be

encountered,

NOT TOUCH ANY METAL PARTS

THE TOOL!

Holdthe tool only by the insulatedgrasping surfaces toprevent electric shock

if you drive into a “live” wire.

nottouchthe bitor the workpiece immediately after operation: they may

be extremely hot and could burn your skin.

Be sure no one is below when using the tool

high locations.

SAVE THESE INSTRUCTIONS.

Removingor installing locator assembly

remove the locator assembly, pull the

locking sleeve forward and then turn

counterclockwise.

To install the locator assembly, screw

clockwise and then push the locking

sleeve

back in lightly toward the motor. Turn the

locking sleeve slightly to match the locking

positions and then push in firmly to lock

the locator in place.

Lockingposition

Locking sleeve-y\

Locator

Removing

installing bit

CAUTION

Always be sure that the tool

switched off and unplugged before removing or installing

bit.

After removing the locator assembly, pull

firmly to remove the magnetic bit holder.

Hold the magnetic bit holder in your hand

and grasp the bit with

pair of pliers. Pull

the bit out of the magnetic bit holder.

Sometimes,

helps to wiggle the bit with

the pliers

you

pull.

Locator

Bit

Magnetic bit holder

install the bit, follow the removal procedures in reverse.

Depth adjustment

Pull the locking

sleeve

forward and then

turn

to adjustthe depth.

Locator

Locking

position

Gear housing

Initially, adjust the locator assembly tocreate

distance of approximately

(3/64")

from the tip of the locator to the base of the screw head. One full turn of the locator

equals

1.5

(1/16")

change in depth. After adjusting

the

locator assembly, push the

locking

sleeve

in to lock the locator in place. Drive

trial screw into your material or

piece

duplicate material. If the depth

not suitable

for

the screw, continue adjusting

untilthe proper depth setting

obtained.

Switch

action

Tool

speed

increased by increasing pres-

sure on the trigger.

start the tool, simply

pull the trigger.

Release

the trigger to stop.

For continuous operation, pull the trigger

and then push in the lock button.

stop

the tool from the locked position, pull the

trigger fully, then release

it.

(3/64")

Trigger switch

Lock

button

CAUTION

Before plugging in the tool, always check to

see

that the trigger switch actuates properly

and returns to the

"OFF"

position when released.

NOTE

Even with the switch on and motor running, the bitwill not rotate untilyoufit the point

of the bit inthe screw head and apply forward pressureto engage the clutch.

Reversing switch action

This tool has

reversing switch to change

the direction of rotation. Move the revers-

ing switch lever to the

position for

clockwise rotation or the

''g\

position for

counterclockwise.

Reversing

switch

lever

CAUTION

Always check the directionof rotation before drilling.

.Use the reversing switch only when the tool comes to

complete stop. Changing the

directionof rotation before the tool stops may ruin the tool.

Operation

Fit the screw on the point of the bit and

place the point of the screw on the surface

of the workpiece to be fastened. Apply

pressure to the tool,

Start

the tool slowly

and then increase the speed gradually.

Withdraw the tool

soon

the clutch

cuts in.

CAUTION

Use the proper bitfor the head of the screw that

you

wish to use.

When fitting the screw onto the point of the bit, be careful not to push in on the screw.

If the screw

pushed in, the clutch will engage and the screw will rotate suddenly. This

could damage

workpiece or cause an injury.

notcontinue unnecessaryclutching operation.

NOTE

Make sure that the bit

inserted straight in the screw head, or the screw and/or bit may

be damaged.

MAINTENANCE

CAUTION

Always be sure that the tool

switchedoff and unplugged before attempting to perform

inspection or maintenance.

To maintain product SAFETY and RELIABILITY, reparis, carbon brush inspection and

replacement, any other maintenance or adjustment should be performed by Makita

Authorized or Factory Service Centers, always using Makita replacement parts.

ACCESSORIES

CAUTION:

These accessories or attachments are recommended for use with your Makitatool specified

this

manual. The use of any other accessories or attachments might present a risk of injury to persons.

The accessories or attachments should be used only in the proper and intended manner.

Size

Phillips insert bit

(10 per pkg.)

Part

No.

784211-2A

784213-A

*#2

784211-6

#2 784211-28

Phillips insert bit

(50

per pkg.)

Size

Part

NO.

784212-OB

Magnetic bit holder

Part No. 784801-1

Nose piece assembly

Part No. 122211-8

Jun

-07-’93

SCREWDRIVER

Model

6800DBV

Model

680

DBV

Note:

The

switch, noise suppressor and other part configuratlons

may

differ from country to country.

MODEL

6800DBV.

68010BV

IF,',"

DESCRIPTION

Jun

-07-'93

""0"

&tD

DESCRIPTION

Fell Cover

Felt

Ring

Localor

Locking

Sleeve

Pan

Head

Screw

M4x55 iWith Washerl

Ring

ea,

tiouslng

Leaf

spmy

Steel Ball

Spindle

Thin Washer

HelicalGear

For

Model 6800DBV

For

Model 6801DBV

Woodruff

Key

Gear

Shalt

Thrust

Needle

Bearing

1023

Name

Plate

Rivet

Pan

Head

Screw

M4x45 iWilh Washerl

Hook

Rubber

Pan Head

Screw

M4x50 IWith Washerl

Compresslo"

Sprlny

Gear

Housinq Cover

Rubber

627LB

For

Model 68OODBV

608LB

For

Model 6801DBV

Fan

ARMATURE ASSEMBLY

iWith

Item

26 291

Ball

Bearing

627LB

Baffle

Plate

FIELD ASSEMBLY

Brush

Holder

Carbon

Brush

Pan

Head

Screw

M4x14 iWith Washer1

Switch

Switch Cover

Handle

Cover

Pari

Head

Scww

M4x28 IWifh Washer1

Swilch

Pan

Head

Screw

M4x18

IWith

Washcrl

Strairi Relief

Cord

Guard

Motor Housing

lns~lafi~n

Washer

Ball

Bearlrlq

Sponge Wasl?er

Note

The

switch

and

other part specifications

may

differ

from

country

This manual suits for next models

Table of contents

Popular Power Screwdriver manuals by other brands

Parkside

Parkside 345138 2004 instructions

AEG

AEG BST 18BLX2-0 Original instructions

Ingersoll-Rand

Ingersoll-Rand D5000 Series Product information

BGS technic

BGS technic 956 manual

Hilti

Hilti SD 6000 operating instructions

Parkside

Parkside PEPS 3 A1 Translation of the original instructions

Festool

Festool TI 15 operating manual

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Operation manual

Skil

Skil 2346 Operating/safety instructions

DeWalt

DeWalt XR LI-ION DCD931 user manual

Festool

Festool DWC 18-2500 operating manual

EINHELL

EINHELL TE-CD 12/1 Li Series Original operating instructions

Stanley

Stanley SCD2 manual

Atlas Copco

Atlas Copco LUM12 SR Product instructions

FAR

FAR TECNUM Original manual translation

GRAPHITE PRO

GRAPHITE PRO 59GP400 instruction manual

Festool

Festool C 12 Li instruction manual

Facom

Facom V.600R instructions