Makita 6891D User manual

Cordless Drywall Screwdriver

Capacity

Drywall screw

mm15132"l

Equipped with Electric Brake

MODEL 6891D

MODEL 6891DW

With

Fast

Charger

No load speed IRPMI

1,400

Dimensions

230

55 mm

260 mm

19"

2-118''

10-1/4"1

Net weight

,2,9

,bsl

INSTRUCTION MANUAL

Battery Cartridge

9000

Voltage

9.6 V

SPEC

CAT

Model DC9700 Fast Charger

Input output Charging time

D.C.

2 V. 9.6 V

A.C. only 50 Hz

Hr.

IMPORTANT

SAFETY INSTRUCTIONS

(For

All

Tools)

WARNING:

WHEN USING ELECTRIC TOOLS, BASIC SAFE-

REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER-

TY PRECAUTIONS SHOULD ALWAYS

FOLLOWED TO

SONAL INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp

or wet locations. Keep work area well

lit.

Don't expose power tools torain.

Don't use tool in presence of flammable liquids or gases.

KEEP CHILDREN AWAY.

All

visitors should be kept away from work area.

Don't let visitors contact tool or extension cord.

STORE IDLETOOLS. When not inuse, tools should be stored indry, and high

or locked-up place

out

reach of children.

DON'T FORCETOOL.

willdo thejob betterand safer at the ratefor which

was intended.

USE RIGHT TOOL. Don't force small tool or attachment to do the job of a

heavy-duty tool. Don't use tool for purpose not intended.

DRESS PROPERLY. Don't wear loose clothingor jewelry. They can be caught

in moving parts. Rubber gloves and non-skid footwear are recommended

when working outdoors. Wear protective hair coveringtocontain long hair.

USE SAFETY GLASSES. Also use face or dust mask if cutting operation is

dusty.

DON'T ABUSE CORD. Never carry tool by cord or yank

todisconnect from

IO.

SECURE WORK. Use clamps or a vise to hold work. It's safer than using

11.

DON'T OVERREACH. Keep proper footing and balance at all times.

12.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and

safer performance. Follow instructions for lubricating and changing acces-

sories. Inspect toolcords periodically and

damaged, haverepairedby autho-

rized service facility. Inspect extension cords periodically and replace if

damaged. Keep handles dry. clean, and free from oil and grease.

13.

DISCONNECTTOOLS. When not inuse, before servicing, and when chang-

ing accessories, such as blades, bits, cutters.

receptacle. Keep cord from heat, oil, and sharp edges.

your hand and

frees both hands to operate tool.

14.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to

see that keysand adjusting wrenches are removed from tool before turning

on.

15.

AVOID UNINTENTIONALSTARTING. Don't carry plugged-intool withfinger

on switch. Be sure switch is OFF when plugging in.

16.

OUTDOOR USE EXTENSIONCORDS. When tool is used outdoors, use only

extension cords intended for use outdoors and

marked.

17.

STAY

ALERT.

Watch what you are doing, use common sense. Don't operate

tool when you are tired.

18.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other

part that is damaged should be carefully checked to determine that

will

operate properly and perform its intended function. Check for alignment of

moving parts, bindingof movingparts, breakage

parts, mounting, and any

other conditions that may affect its operation. A guard or other part that

is damaged should be properly repaired or replaced by an authorized serv-

ice center unless otherwise indicatedelsewhere

this instruction manual.

Have defective switches replaced

authorized service center. Don't use

tool

switch does not turn

on and off.

IS.

GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded

surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

20.

REPLACEMENT PARTS. When servicing, useonly identicalreplacementparts.

VOLTAGE WARNING: Before connecting the tool toa power source (receptacle,

outlet, etc.) be sure the voltage supplied is the same as that specified on the

nameplate of the tool. A power source with voltage greater than that specified

for the tool can result inSERIOUS INJURY to the user

as well as damage to

the

tool. If

doubt, DO NOT PLUG IN THE TOOL. Using a power source with

voltage less than the nameplate rating is harmful to

the

motor.

IMPORTANT SAFETY INSTRUCTIONS

Length of Cord (Feet)

100

AWG Size of Cord

18 18 18

SAVE

THESE

INSTRUCTIONS

This manual

150

contains important safety and operating instructions for battery charger.

Before using battery charger, read all instructions and cautionary markings

(1)

battery charger,

(2)

battery, and

(3)

product using battery.

CAUTION

To reduce risk of injury, charge only MAKITA Battery

7000,

9000

9100.

Other types of batteries may burst causing personal injury

and damage.

Do not expose charger to rain or snow.

Use of an attachment not recommended or sold by the battery charger

manufacturermay result

a risk of fire, electricshock, or injurytopersons.

To reduce risk of damage toelectric plug and cord, pull by plug rather than

cord when disconnecting charger.

Make sure cord is located

that

will not be stepped on, tripped over,

or otherwise subjected to damage or stress.

An extension cord should not be used unless absolutely necessary. Use of

improper extension cord could result in a risk of fire and electric shock.

extension cord must be used, make sure:

a. That pinsonplugof extensioncord are the same number, size, and shape

b. That extension cord is properly wired and

good electrical condition; and

c. That wire size isat least as largeas the one specified

the table below.

as those of plug on charger;

TABLE

RECOMMENDED MINIMUM AWG

SIZE

FOR

EXTENSION CORDS

FOR

BATTERY CHARGERS

Do not operate charger with damaged cord or plug

replace them im-

mediately.

IO.

Do not operate charger

has received a sharp blow, been dropped, or

otherwise damaged in any way; take

to a qualified serviceman.

11.

Do not disassemble charger or battery cartridge; take

to a qualified

serviceman when service or repair is required. Incorrect reassembly may

result

a risk of electric shock or fire.

12.

To reducerisk

electric shock, unplugcharger from outlet beforeattempt-

ingany maintenanceor cleaning. Turningoff controls will not reducethis risk.

ADDITIONAL SAFETY RULES

FOR CHARGER

BATTERY CARTRIDGE

Do not charge Battery Cartridge when temperature is BELOW 10°C

(5OOF)

or ABOVE

4OoC

(104OF).

Do notattempttousea step-up transformer, an engine generator or DC power

Do not allow anything to cover or clog the charger vents.

Always cover the battery terminals

with

the battery cover when the battery

A battery short can cause a large current flow, overheating, possible burns

receptacle.

cartridge is not used.

and even a breakdown.

(1)

not touch the terminals

with

any conductive material.

(2)

Avoid storing battery cartridge

a container

with

other metalobjects such

(3)

Do not expose battery cartridge to water or rain.

ture may reach or exceed 5OoC

(122OF).

completely worn out. The battery cartridge can explode

a fire.

as nails, coins, etc.

notstore the tool and Battery Cartridge

locations where the tempera-

not incinerate the Battery Cartridge even if

is severely damaged or is

ADDITIONAL SAFETY RULES

Be aware that this tool is always

an operating condition, because

does

Always be sure you have a firm footing.

Hold the tool firmly.

Keep hands away from rotating parts.

When driving into walls, floors or wherever "live" electrical wires may be

encountered,

NOT TOUCH ANY METAL PARTS

THE TOOL!

Hold

the

tool

only

the insulated graspingsurfaces topreventelectric shock

if you drive into a "live" wire.

Do nottouch the bit or the workpiece immediatelyafter operation; they may

be extremely hot and could burn your skin.

not have to be plugged into an electrical outlet.

Be sure no one

below when using the tool

high locations.

SAVE THESE INSTRUCTIONS.

Installing or removing battery cartridge

Always switch off the tool before insertion or removal of the battery cartridge.

remove the battery cartridge, pull out

the

set

plate on the tool and grasp both

sides of the cartridge while withdrawing it

from the barrel.

insert the battery cartridge, align the

tongue on the battery cartridge with the

groove in the housing and slip

into

place. Snap the

s'et

plate back into place.

Be sure to close the

set

plate fully before

using the tool.

Set

plate

not use force when inserting the battery cartridge.

the cartridge does notslide in easily,

not beinginsertedcorrectly.

Charging

Plug the fast charger into your power

source. Insert the battery cartridge

that

the plus and minus terminals on the bat-

tery cartridge are on the same sides

their

respective markings on the fast charger.

Insert the cartridge fully into the port

that

rests on the charger portfloor.

Press the start button (red). The charging

light will come on and charging will begin.

If the charging light does not come on,

press the reset button (yellow) first, then

the start button (red). If the charginglight

Start button

Reset

light

button

goes out within

seconds even after pressing the reset button and start button

couple

of times, the battery cartridge

dead. (CAUTION

Wait for more than

seconds after

the charging light goes out to press the reset button again.) Replace

with

new one.

When the charginglight goes out after about one hour, you may remove the fully charged

battery cartridge.

After charging, unplugthe charger from the power source.

CAUTION

Your new battery cartridge

notcharged. You will need tocharge

before use.

not keep the button pressed in with tape, etc. or the circuit will not function pro-

perly.

Also,

malfunction of the charger may result possibly causing overheating, etc.

If you try to charge

cartridge from

just-operated tool, sometimes the charginglight

will not come on.

this occurs,

let

the cartridge

cool

off for

while. Then re-insert

and try tocharge

once more.

When you charge

newbattery cartridge or

battery cartridge which has notbeen used

for

long period,

may not acceqt

full charge. This

normal condition and does

not indicate

problem. You can recharge the battery cartridge fully after discharging

almostcompletely

couple of times.

If youwish to charge two battery cartridges, allow 15minutes betweenchargings on the

fast

charger.

Removing

installing bit

CAUTION

Always be sure

that

the tool

switched off and the battery cartridge

removed before

removing or installingthe bit.

To remove the bit, first pull the stopper

out of the locator.

Then grasp the bit with

pair of pliers and

pull the bit out

the magneticbit holder.

Sometimes,

helps to wiggle the bit with

the pliers

you pull.

To install the bit, push the bit firmly

into the magnetic bit holder. Then install

the stopper by pushing it firmly into the

locator.

Depthadjustment

Loosen the screw and adjustthe locator by

turning

to create

distance of approxi-

mately 1.5

mm (1/16”

5/64”)

from

the end

the stopper to the tip of the

bit. Tighten the screw to lock the locator.

Then, drive

trial screw into your material

or into

piece

duplicate material. Ob-

serve the depth

screw penetration into

the material. Ifthe depth is not suitablefor

the screw, continue adjusting until the

proper depth setting

obtained.

NOTE

Lock

rina

Stopper

Locator

Screw

Bit holder

Lock ring

1.5

(1116’‘

5/64”)

Locator

The locator will be locked by tightening the screw slightly.

not tighten

excessively,

may be damaged.

Switch action

Tool

speed

increased by increasing pres-

sure

the trigger.

start the tool,

simply pull the trigger.

Release

the trigger

to stop.

CAUTION

Before inserting the battery cartridge into the tool, always check to

see

that the trigger

switch actuates properly and returns to the

"OFF"

position when released.

Reversingswitch action

This tool has

reversing switch to change

the direction of rotation. Slide the revers-

ing switch to the right for clockwise rota-

tion or to the left for counterclockwise.

eversing

switch

CAUTION

Always check the direction

rotation before operation.

*Use the reversing switch only when the tool comes to

complete stop. Changing the

directionof rotation before the tool stops may ruin the tool.

Screwdriving operation

Place the point of the driver bit in the screw head and apply pressure to the tool. Start

the tool.

Release

the trigger

soon

the stopper touches the workpiece. The electric

brakewill then stop the tool immediately.

NOTE

Use the proper bitfor the head of the screw that you wish to use.

Make sure that the driver bit

inserted straight in the screw head, or the screw and/or

you continue driving the screw after the screw

fully seated, the screw and/or bit

bitmay be damaged.

may be damaged.

Overload protector

The overload protector automatically cuts out to break the circuit whenever heavy work

prolonged.

Wait

20-30

seconds before resuming operation.

MAINTENANCE

CAUTION

Always be sure that the tool

switched off and the battery cartridge

removedbefore

attempting toperform inspection or maintenance.

To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment

should be performed by Makita Authorized or Factory Service Centers, always using

Makita replacementparts.

ACCESSORIES

CAUTION

These accessories or attachments are recommended for use with your Makita tool specified in this

manual. The use

any other accessories or attachments might present

risk of injury to persons.

The

accessories or attachments should

used only in the proper and intended manner.

.Phillips insert bit 2-25

Magnetic bitholder

6.35-60

Part No. 784211-2A (10per pkg.) Part No. 784807-9

Part No. 784211-28

(50

per pkg.)

Fast

charger

Model DC9700

Part

No.

113103-2

Battery cartridge

9000

Part No. 632007-4

Battery holster

Part No. 823033-3C

Charger 12Vfor car

Model DC9112

Part

No.

113110-5

Battery cover

Part No. 414938-7

Steel carrying case

Part No. 181965-6

This manual suits for next models

Table of contents

Popular Power Screwdriver manuals by other brands

Parkside

Parkside 345138 2004 instructions

AEG

AEG BST 18BLX2-0 Original instructions

Ingersoll-Rand

Ingersoll-Rand D5000 Series Product information

BGS technic

BGS technic 956 manual

Hilti

Hilti SD 6000 operating instructions

Parkside

Parkside PEPS 3 A1 Translation of the original instructions

Festool

Festool TI 15 operating manual

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Operation manual

Skil

Skil 2346 Operating/safety instructions

DeWalt

DeWalt XR LI-ION DCD931 user manual

Festool

Festool DWC 18-2500 operating manual

EINHELL

EINHELL TE-CD 12/1 Li Series Original operating instructions

Stanley

Stanley SCD2 manual

Atlas Copco

Atlas Copco LUM12 SR Product instructions

FAR

FAR TECNUM Original manual translation

GRAPHITE PRO

GRAPHITE PRO 59GP400 instruction manual

Festool

Festool C 12 Li instruction manual

Facom

Facom V.600R instructions