Makita 6805BV User manual

Screwdriver

Self drilling screw

MODEL

6805BV

Variable speed

Reversing

Machine screw Wood screw

INSTRUCTION MANUAL

DOUBLE

INSULATION

SPEC

CAT

Manufacturer reserves the right to change specifications without notice.

Note: Specifications may differ from country

country.

WARNING: For your personal safety, READ and UNDERSTAND before using

SAVE THESE INSTRUCTIONS

FOR

FUTURE REFERENCE.

IMPORTANT

SAFETY INSTRUCTIONS

(For

All

Tools)

WARNING:

WHEN USING ELECTRICTOOLS, BASIC SAFETY

PRECAUTIONSSHOULD ALWAYS BE FOLLOWED TO REDUCE

THE RISK

FIRE, ELECTRIC SHOCK, AND PERSONAL

INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

10.

11.

12.

13.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp

or wet locations. Keep work area well

lit.

Don't expose power tools to rain.

Don't use tool

presence of flammable liquids

gases.

KEEP CHILDREN AWAY. All visitors should be kept away from work area.

Don't let visitors contact tool or extension cord.

STORE IDLETOOLS. When not

use, tools should be stored indry, and high

or locked-up place

out of reach of children.

DON'T FORCETOOL.

will do thejob better and safer atthe ratefor which

was intended.

USE RIGHT TOOL. Don't force small tool or attachment to do the job of a

heavy-duty tool. Don't use tool for purpose not intended.

DRESS PROPERLY. Don't wear looseclothingor jewelry. They can be caught

moving parts. Rubber gloves and non-skid footwear are recommended

when working outdoors. Wear protective hair covering to contain long hair.

USE SAFETY GLASSES. Also use face or dust mask if cutting operation is

dusty.

DON'T ABUSE CORD. Never carry tool

cord or yank

todisconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

SECURE WORK. Use clamps or a vise to hold work. It's safer than using

your hand and

frees both hands to operate tool.

DON'T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and

safer performance. Follow instructions for lubricating and changing acces-

sories. Inspecttoolcords periodicallyandifdamaged, have repairedby autho-

rized service facility. Inspect extension cords periodically and replace if

damaged. Keep handles dry, clean, and free from oil and grease.

DISCONNECTTOOLS. When not inuse, before servicing, and when chang-

ing accessories, such

blades, bits, cutters.

14.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to

see that keysand adjusting wrenches are removed from tool before turning

on.

15.

AVOID UNINTENTIONALSTARTING. Don’t carry tool with finger on switch.

Be sure switch is OFF when plugging in.

16.

OUTDOOR USE EXTENSIONCORDS. When tool is usedoutdoors, use only

extension cords intended for use outdoors and

marked.

17.

STAY ALERT. Watch what youare doing, use common sense. Don’t operate

tool when you are tired.

18.

CHECK DAMAGED PARTS. Before further use of

the

tool, a guard or other

part that is damaged should be carefully checked to determine that

will

operate properly and perform itsintended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts, mounting, and

any other conditions that may affect its operation. A guard or other part

that is damaged should be properly repaired or replaced by an authorized

service center unless otherwise indicated elsewhere in this instruction

manual. Havedefective switches replacedby authorizedservicecenter. Don‘t

use tool if switch does not turn

on and off.

19.

GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded

surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

20.

REPLACEMENTPARTS. When servicing, useonly identicalreplacementparts.

21.

POLARIZEDPLUGS. To reduce the risk of electric shock, this equipment has

a polarized plug (one blade is wider than the other). This plug will fit in a

polarized outlet only one way.

the plug does not

fit

fully in the outlet,

reverse the plug. If

stilldoes notfit, contact a qualified electriciantoinstall

the proper outlet. Do not change the plug in any way.

VOLTAGE WARNING: Beforeconnecting the tool to a power source (receptacle,

outlet, etc.) be sure the voltage supplied is the same as that specified on the

nameplate of the tool. A power source with voltage greater than that specified

for the tool can result

SERIOUS INJURY to the user

as well as damage to

the tool.

in doubt,

NOT PLUG IN THE TOOL. Using a power source with

voltage less than the nameplate rating is harmful to the motor.

ADDITIONAL SAFETY RULES

Hold the tool firmly.

Always be sure

you

have a firm footing.

Be sure no one is below when using the tool

high locations.

Keep hands away from rotating parts.

When driving into walls, floors or wherever "live" electrical wires may be

encountered,

NOT TOUCH ANY METAL PARTS

THE TOOL!

Holdthe toolonly bythe insulatedgraspingsurfaces topreventelectric shock

you

drive into a "live" wire.

nottouchthe bitor the workpiece immediately after operation: they may

be extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

Removing

installingbit

CAUTION

Always be sure that the tool

switched off and unplugged before removingor installing

the bit.

To remove the bit, first pull the front cap

off and then pull the bit firmly. To install

the bit, insert

into the tool

far

will go and then replacethe front cap.

Depthadjustment

When you wish to drive self drilling screws,

etc.,

adjust the depth

follows. Turn the

locator toadjust the depth.

Initially, adjust the locator to create

dis-

tance of approximately

(3/64”)

from

the tip of the front cap (which works in

conjunction with the locator) to the base

of the screw head. One full turn of the

locator equals

(3/64“)

change in

depth. After adjusting the locator, turn

the adjusting ring

that the

6”

mark

aligned with the pointer on the gear hous-

ing. Drive

trial screw into your material

piece of duplicate material. If the

depth

not

suitable

for the screw, con-

tinue adjusting until the proper depth

set-

ting

obtained.

Adjusting ring-

(3/64”)

Adjustingfasteningtorque

When you wish to drive machine screws,

wood screws, hex bolts etc. with the pre-

determined torque, adjust the fastening

torque

follows.

The fastening torque may be adjusted by

turning the adjusting ring. Before turning

the adjusting ring, turn the locator in the

direction of the arrow

far

will go

without forcing. The torque

increased

by turning the adjusting ring in the direc-

tion of the arrow and decreased by turn-

ing

in the opposite direction. Align the

number

on the adjusting ring with the pointer on the gear housing. Drive

trial screw

into your material or

piece of duplicate material. Ifthe fasteningtorque

not suitable

for the screw, continue adjustinguntil the proper torque

obtained.

CAUTION

The adjusting ring should be turned only within the numbered range.

should not be

forced beyondthis range.

Switchaction

Tool speed

increased by increasing

pressure on the trigger. To start the tool,

simply pull the trigger.

Release

the trigger

to stop. Forcontinuousoperation, pull the

trigger and then push in the lock button.

To stop the tool from the lockedposition,

pull the trigger fully, then release

it.

Trigger

switch

Lock

button

CAUTION

Before plugging in the tool, always check to

see

that the trigger switch actuates properly

and returnsto

the

"OFF"

positionwhen released.

NOTE

Even with the switch on and motor running, the bit will not rotate until you fit the point

the bitinthe screw head and apply forward pressure toengage the clutch.

Reversing switch action

This tool has

reversing switch to change

the direction

rotation. Move

the

revers-

ing switch lever to the

position for

clockwise rotation or the position for

counterclockwise.

Reversing

switch

lever

CAUTION

Always check the direction of rotationbefore operation.

*Use the reversing switch only when the tool comes to

complete stop. Changing the

direction of rotationbefore the tool stops may ruin the tool.

Operation

Fit the screw

the point of the bit and

place the point

the screw on the surface

of the workpiece to be fastened. Apply

pressure to the tool and start

it.

Withdraw

the

tool

soon

the clutch cuts in.

Then release the trigger.

CAUTION

Use the proper bitfor the head of the screw that you wish to use.

When fitting the screw onto the point of the bit, be careful not to push inon the screw.

If the screw

pushed in, the clutch will engage and the screw will rotatesuddenly. This

could damage

workpiece or cause an injury.

notcontinue unnecessaryclutching operation.

NOTE

Make sure that the driver bit

insertedstraight in the screw head, or the screw and/or

When driving wood Screws, predrill pilot

bit may be damaged.

holes to make driving

easier

and to pre-

vent splitting of the workpiece.

See

the

chart.

wood screw of

pilot

hole

1/64"

13/64"

7/32"

3/16"

1/8"

9/64"

5/32"

iia"

15/64"

1/64"

114"

164''

MAINTENANCE

CAUTION

Always be sure

that

the

tool

switched off and unplugged beforeattempting toperform

inspectionor maintenance.

maintain product SAFETY and RELIABILITY, repairs, carbon brush inspectionand

replacement, any other maintenance or adjustment should be performed by Makita

Authorized or Factory Service Centers, always using Makita replacement parts.

ACCESSORIES

Part

No.

CAUTION

These accessories or attachments are recommended for

use

with your Makita tool specified in this

manual. The use

any other accessories or attachments might present

risk

injury to persons.

The accessories or attachments should be usedonly in the proper and intended manner,

Magnetic socket bit Front cap

Size

Part

No.

Size

784803-7 114"

784805-3

7/16"

Phillips bit

Part

No.

Size

322124-5 114''

322120-3

Slotted bit

784215-0A

Part

No.

Size

784010-OA

#5F

784011-0A

#7F

Square drill bit

Part

No.

784606-0A

Steel carrying case

Part

No.

181853-7

May-28-'93

SCREWDRIVER

Model

6805BV

Note: The switch, noise suppressor and other part configurations

may differ from country

country.

Other manuals for 6805BV

Table of contents

Popular Power Screwdriver manuals by other brands

Parkside

Parkside 345138 2004 instructions

AEG

AEG BST 18BLX2-0 Original instructions

Ingersoll-Rand

Ingersoll-Rand D5000 Series Product information

BGS technic

BGS technic 956 manual

Hilti

Hilti SD 6000 operating instructions

Parkside

Parkside PEPS 3 A1 Translation of the original instructions

Festool

Festool TI 15 operating manual

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Operation manual

Skil

Skil 2346 Operating/safety instructions

DeWalt

DeWalt XR LI-ION DCD931 user manual

Festool

Festool DWC 18-2500 operating manual

EINHELL

EINHELL TE-CD 12/1 Li Series Original operating instructions

Stanley

Stanley SCD2 manual

Atlas Copco

Atlas Copco LUM12 SR Product instructions

FAR

FAR TECNUM Original manual translation

GRAPHITE PRO

GRAPHITE PRO 59GP400 instruction manual

Festool

Festool C 12 Li instruction manual

Facom

Facom V.600R instructions