Makita 6802BV User manual

Screwdriver

shank

Capacities

MODEL

6802BV

Variable Speed

Reversing

No load speed Overall Net

(RPM)

length weight

INSTRUCTION MANUAL

Self drilling screw

....

(114")

DOUBLE

INS

17kg

265

2'500

(10-112")

(3.7

Ibsl

114" Hex

SPEC

CAT1

IMPORTANT

SAFETY

INSTRUCTIONS

(For

All

Tools)

WARNING:

WHEN USING ELECTRICTOOLS, BASICSAFETY

PRECAUTIONSSHOULD ALWAYS BE FOLLOWED TO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL

INJURY, INCLUDING THE FOLLOWING:

READ ALL

INSTRUCTIONS.

IO.

11.

12.

13.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

CONSIDER WORK AREA ENVIRONMENT. Don't use power tools

damp

or wet locations. Keep work area well

lit.

Don't expose power tools to rain.

Don't use tool

presence of flammable liquids or gases.

KEEP CHILDREN AWAY. All visitors should be kept away from work area.

Don't let visitors contact tool or extension cord.

STORE IDLETOOLS. When not

use, toolsshould be stored indry, and high

or locked-up place

out of reach of children.

DON'T FORCE TOOL.

will

dothejob better and safer atthe ratefor which

was intended.

USE RIGHT TOOL. Don't force small tool or attachment to do the job of a

heavy-duty tool. Don't use tool for purpose not intended.

DRESS PROPERLY. Don't wear loose clothingor jewelry. They can be caught

in moving parts. Rubber gloves and non-skid footwear are recommended

when working outdoors. Wear protective hair coveringtocontain long hair.

USE SAFETY GLASSES. Also use face or dust mask if cutting operation is

dusty.

DON'T ABUSE CORD. Never carry tool by cord or yank

todisconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

SECURE WORK. Use clamps or a vise to hold work. It's safer than using

your hand and

frees both hands to operate tool.

DON'T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and

safer performance. Follow instructions for lubricating and changing acces-

sories. Inspect toolcords periodically and

damaged, haverepairedby autho-

rized service facility. Inspect extension cords periodically and replace

damaged. Keep handles dry, clean, and free from oil and grease.

DISCONNECTTOOLS. When not

use, before servicing, and when chang-

ing accessories, such as blades, bits, cutters.

14.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to

see that keysandadjusting wrenches are removedfromtool before turning

on.

15. AVOID UNINTENTIONALSTARTING. Don’t carry tool

with

finger onswitch.

Be sure switch is

OFF

when plugging

in.

16.

OUTDOOR USE EXTENSION CORDS. Whentool isused outdoors, useonly

extension cords intended for use outdoors and

marked.

17. STAY ALERT. Watch what you are doing, use commonsense. Don’t operate

tool when you are tired.

18.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other

part that is damaged should be carefully checked to determine that

will

operate properly and performitsintendedfunction. Check for alignment of

moving parts, binding of moving parts, breakage of parts, mounting, and

any other conditions that may affect its operation. A guard or other part

that is damaged should be properly repaired or replaced by an authorized

service center unless otherwise indicated elsewhere

this instruction

manual. Havedefective switches replaced byauthorized service center. Don’t

use tool if switch does not turn

on and off.

19.

GUARD AGAINST ELECTRICSHOCK. Prevent body contact

with

grounded

surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

20.

REPLACEMENTPARTS. Whenservicing, useonly identicalreplacement parts.

21.

POLARIZED PLUGS. To reducethe risk of electric shock, this equipment has

a polarized plug (one blade

wider than the other). This plug

will

fit

polarized outlet only one way.

the

plug

does

not

fit fully

the outlet,

reversetheplug. If

stilldoes notfit, contact a qualified electriciantoinstall

the proper outlet.

not change the

plug

any way.

VOLTAGE WARNING: Before connecting the tool toa power source (receptacle,

outlet, etc.) be sure the voltage supplied is the same as that specified on the

nameplate of the tool. A power source

with

voltage greater than that specified

for the tool can result

SERIOUS INJURY tothe user

as well as damage to

the tool. If

doubt,

NOT PLUG IN THE TOOL. Using a power source

with

voltage less than the nameplate rating is harmful to the motor.

ADDITIONAL SAFETY RULES

Always be sure you have a firm footing.

Hold the tool firmly.

Keep hands away from rotating parts.

When driving into walls, floors or wherever "live" electrical wires may be

encountered,

NOT TOUCH ANY METAL PARTS

THE

TOOL!

Holdthetoolonly bythe insulatedgrasping surfacestoprevent electric shock

if you drive into a "live" wire.

nottouchthe bit or the workpiece immediately after operation: they may

be extremely hot and could burn your skin.

Be sure no one is below when using the tool

high locations.

SAVE THESE INSTRUCTIONS.

Removing or installinglocator assembly

remove the locator assembly, pull the

locking

sleeve

forward and then turn

counterclockwise.

install the locator

assembly, screw

clockwise and then

push the locking

sleeve

back in lightly

toward the motor. Turn the locking

sleeve

slightly to match the lockingpositionsand

then push in firmly to lock the locator in

place.

Locking

position

Removing

installingbit

CAUTION:

Always be sure that the tool

switched off and unplugged before removing or installing

the bit.

After removing the locator assembly, pull

firmly

remove the magnetic socket bit.

install the bit, insert

into the tool

far

will go.

Locator

Depthadjustment

Pull the locking

sleeve

forward and then

turn

to adjust the depth.

Locking position

Gear housing

Initially; adjust the locator assembly to

create

distance of approximately

0.5

(1/64") from the tip of the locator to the

tip of the socket bit. One full turn of the

locator equals 1.5 mm (1/16") change in

depth. After adjustingthe locatorassembly,

push the locking

sleeve

in to lock the

locator in place. Drive

trial screw into

your material or

piece of duplicate mate-

rial.

the depth

not suitable for the

screw, continue adjusting until the proper

depth setting

obtained.

Switch

action

Tool

speed

increased by increasing pres-

sure on the trigger. To start the tool,

simply pull the trigger.

Release

the trigger

to stop. For continuous operation, pullthe

trigger and then push in the lock button.

To stop the tool from the lockedposition,

pullthe trigger fully, then release

it.

CAUTION

0.5

/64")

Locator

Trigger switch

Lock

button

Before plugging in the tool, always check to

see

that the trigger switch actuates properly

and returnsto the "OFF" position when released.

NOTE

Even with the switch on and motor running, the bitwill not rotate until you

fit

the point

of the bit inthe screw head and apply forward pressure toengage the clutch.

Reversingswitch action

This tool has

reversing switch to change

the direction of rotation. Move the revers-

ing switch lever to the

position for

clockwise rotation or the

position for

counterclockwise.

CAUTION

Always check the direction of rotation beforeoperation.

*Use

the

reversing switch only when the tool comes to

complete stop. Changing the

direction

rotation beforethe tool stops may ruinthe tool.

Reversing

switch

lever

Operation

Fit the screw on the point of the bit and

place

the

point of the screw on the surface

of the workpiece to be fastened. Apply

pressure to the tool. Start the tool slowly

and then increase the speed gradually.

Withdraw the tool

soon

the clutch

cuts in.

CAUTION

Use the proper bitfor the head of the screw that you wish to use.

When fitting the screw onto the point of the bit, be careful not to push in

the screw.

If the screw

pushed in, the clutch will engage and the screw will rotate suddenly. This

could damage

workpiece or cause an injury.

not continue unnecessary clutching operation.

NOTE

Make sure that the bit

inserted straight in the screw head, or the screw and/or bitmay

be damaged.

When using insert bit

Fit together the insert bit and magnetic

bit holder

shown in the figure on the

right. Install

locator assembly for an in-

sert bit.

Then adjust depth setting. Initially, adjust

the locatorassembly to create

distance of

approximately

(3/64")

from the tip

of the locator to the base of the screw

head. Continue adjusting until the proper

depth setting

obtained by following the

methodof "Depth adjustment".

Locator

Insert

bit

Magnetic bit holder

r------

(3/64")

remove the bit, pull the magnetic bit holder firmly. Hold the magnetic bit holder in

your hand and grasp the bit with

pair of pliers. Pull the bit out of the magnetic bit

holder. Sometimes,

helpstowiggle the bitwith the pliers

you pull.

MAINTENANCE

CAUTION

Always be sure that the tool

switched off and unpluggedbefore attempting toperform

inspectionor maintenance.

To maintain product SAFETY and RELlABlLITY, repairs, carbon brush inspection

and replacement, any other maintenance or adjustment should be performed by Makita

Authorized or Factory Service Centers,

always

using Makita replacementparts.

ACCESSORIES

CAUTION:

These accessories or attachments are recommended for use with your Makitatool specified inthis

manual. The use

any other accessories or attachments might present a risk

injury to persons.

The accessories or attachments should be used only

the proper and intended manner.

122213-4

122212-6

Nose piece assembly

Part No. 122211-8

318"

Magnetic bit holder

Part No. 784801-1

784211-28

Nose piece assembly

Part

No.

Size

122214-2

114"

Magnetic socket bit Phillips insert bit

Q'ty

per

pkg

784803-7 784212-OA

784804-5 511

784211-2A

784802-9 318" m784211-B #2

784213-A #3 10

784212-08

Other manuals for 6802BV

Table of contents

Popular Power Screwdriver manuals by other brands

Parkside

Parkside 345138 2004 instructions

AEG

AEG BST 18BLX2-0 Original instructions

Ingersoll-Rand

Ingersoll-Rand D5000 Series Product information

BGS technic

BGS technic 956 manual

Hilti

Hilti SD 6000 operating instructions

Parkside

Parkside PEPS 3 A1 Translation of the original instructions

Festool

Festool TI 15 operating manual

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Operation manual

Skil

Skil 2346 Operating/safety instructions

DeWalt

DeWalt XR LI-ION DCD931 user manual

Festool

Festool DWC 18-2500 operating manual

EINHELL

EINHELL TE-CD 12/1 Li Series Original operating instructions

Stanley

Stanley SCD2 manual

Atlas Copco

Atlas Copco LUM12 SR Product instructions

FAR

FAR TECNUM Original manual translation

GRAPHITE PRO

GRAPHITE PRO 59GP400 instruction manual

Festool

Festool C 12 Li instruction manual

Facom

Facom V.600R instructions