Makita 6710D User manual

Cordless Screwdriver

Wood

screws

Machine screws

MODEL 6710D

MODEL 6710DW

With Fast Charger

weight

speed length

Nuts

INSTRUCTION MANUAL

11.4'

x2'l

SPECIFICATIONS

220

195

114")

(1/4")

Rimin

17-518")

12.4

lhsl

Model67100

Battery Cartridge 7000 Model OC7100 Fast charger

72V

Dimensions

A.C

only

DC 145

72V

314"

1/8"

2 318")

lhsl

Net

weight

IMPORTANT

SAFETY INSTRUCTIONS

(For

All

Tools)

WARNING:

WHEN USING ELECTRIC TOOLS, BASIC SAFE-

REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER-

TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO

SONAL INJURY, INCLUDING THE FOLLOWING:

READ

ALL

INSTRUCTIONS.

IO.

11.

12.

13.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

CONSIDER WORK AREA ENVIRONMENT. Don't use power tools

damp

or wet locations. Keepwork area well

lit.

Don't exposepower tools torain.

Don't use tool

presence of flammable liquids or gases.

KEEP CHILDRENAWAY. All visitors should be kept away from work area.

Don't let visitors contact tool or extension cord.

STORE IDLE TOOLS. When not

use, tools should be stored

dry, and

high or locked-up place

out of reach of children.

DON'T FORCETOOL.

willdothejob betterand safer attheratefor which

was intended.

USE RIGHT TOOL. Don't force small tool or attachment to do the job of

a heavy-duty tool. Don't use tool for purpose not intended.

DRESS PROPERLY. Don't wear looseclothingorjewelry. They can becaught

moving parts. Rubber gloves and non-skidfootwear are recommended

whenworking outdoors. Wear protective hair coveringtocontainlonghair.

USE SAFETY GLASSES. Also use face or dust mask if cutting operation

is dusty.

DON'T ABUSE CORD. Never carrytool

cordor yank

todisconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

SECURE WORK. Use clamps or a vise to hold work. It:s safer than using

your hand and

frees both hands to operate tool.

DON'T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keeptools sharp and clean for better and

safer performance. Followinstructionsfor lubricating andchangingacces-

sories. Inspect tool cords periodically and if damaged, have repaired by

authorized service facility. Inspectextension cords periodically and replace

if damaged. Keep handles dry, clean, and free from oil and grease.

DISCONNECTTOOLS. When not

use, beforeservicing, and whenchang-

ing accessories, such as blades, bits, cutters.

14.

15.

16.

17.

18.

19.

20.

REMOVEADJUSTING KEYS AND WRENCHES. Form habitof checkingto

see that keys and adjusting wrenches are removed from tool before turn-

ing

on.

AVOID UNINTENTIONALSTARTING. Don't carry plugged-in tool

with

finger

on switch. Be sure switch is OFF when plugging

in.

OUTDOOR USEEXTENSIONCORDS. Whentoolisusedoutdoors, useonly

extension cords intended for use outdoors and

marked.

STAY ALERT. Watch what you are doing, use common sense. Don't oper-

ate tool when you are tired.

CHECK DAMAGEDPARTS. Before further use of the tool, a guard or other

part that is damaged should be carefully checkedto determinethat

will

operate properly and perform its intended function. Check for alignment

of movingparts, binding of movingparts, breakageof parts, mounting, and

any other conditions that may affect its operation. A guard or other part

that is damaged should be properly repaired or replaced by an authorized

servicecenter unlessotherwise indicatedelsewhere

this instruction manu-

al. Have defective switches replaced by authorized service center. Don't

use tool

switch does not turn

on and off.

GUARDAGAINST ELECTRIC SHOCK. Preventbodycontactwithgrounded

surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

REPLACEMENT PARTS. When servicing, use only identical replacement

parts.

VOLTAGE WARNING: Before connectingthe tooltoa power source (receptacle,

outlet, etc.) be sure the voltage supplied is the same as that specified on the

nameplateof the tool. A power source withvoltage greater than that specified

for the tool can result

SERIOUSINJURY tothe user

as well as damage to

the tool. If in doubt, DO NOT PLUG INTHE TOOL. Using a power source with

voltage less than the nameplate rating is harmful to the motor.

IMPORTANT SAFETY INSTRUCTIONS

Length of Cord (Feet)

AWG Size

Cord

SAVE THESE INSTRUCTIONS

This manual

100 150

18 16

contains important safety and operating instructions for battery charger.

Before usingbattery charger, read all instructionsand cautionary markings

(1)

battery charger,

(2)

battery, and

(3)

product using battery.

CAUTION

To reduce risk of injury, charge only MAKITA Battery

7000.

Other types of .batteries may burst causing personal injury and damage.

Do not expose charger to rain or snow.

Use of an attachment not recommended

sold by the battery charger

manufacturer mayresult ina risk of fire, electric shock, or injurytopersons.

To reduce risk of damage toelectric plugand cord, pullby plug rather than

cord when disconnecting charger.

Makesure cord is located

that

will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

An extension cord should not be used unless absolutely necessary. Use of

improper extension cord could result

a risk of fire and electric shock. If

extension cord must be used, make sure:

a. That pinsonplugof extension cord are the same number, size, and shape

b. That extension cordisproperly wiredand ingood electrical condition; and

c. That wire size is at least as large as the one specified

the table below.

TABLE

RECOMMENDED MINIMUM AWG SIZE

FOR

EXTENSION CORDS FOR BATTERY CHARGERS

as those of plug on charger;

ADDITIONAL SAFETY RULES

FOR

CHARGER

BATTERY CARTRIDGE

Do not charge Battery Cartridge when temperature is BELOW

10°C

(SOOF)

or ABOVE

4OoC (104OF).

Donotattempttouseastep-up transformer, an enginegenerator or DC power

Do not allow anything to cover or clog the charger vents.

Always cover the batteryterminals withthe battery cover when the battery

5. A battery short can cause a large current flow, overheating, possible burns

receptacle.

cartridge

not

used.

and even a breakdown.

(1)

Do not touch the terminals with any conductive material.

(2)

Avoid storing battery cartridge ina container with other metalobjects such

(3)

Do not expose battery cartridge to water or rain.

ture may reach or exceed 5OoC

(122OF).

completely worn out. The battery cartridge can explode

a fire.

as nails, coins, etc.

Do not store the tool and Battery Cartridge in locations where the tempera-

Do not incinerate the Battery Cartridge even if

is severely damaged or is

ADDITIONAL SAFETY RULES

FOR

CORDLESS SCREWDRIVER AND DRILL

Be aware that this tool is always in an operating condition, because

does

Always be sure you have a firm footing.

Hold the tool firmly.

Keep hands away from rotating parts.

5. When drilling intowalls, floors or wherever "live" electrical wires may be en-

countered, DO NOT TOUCH ANY METAL PARTS

THE TOOL!

Holdthe toolonly by the plastic handle or plastic tool bodytopreventelectric

shock if you drill into a "live" wire.

not have to be plugged into an electrical outlet.

Be sure no one is below when using the tool

high locations.

Do not leave the tool running. Operate the tool only when hand-held.

Do not touch the drill bit or the workpiece immediately after operation, they

may be extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

Installingor removingbattery cartridge

Always switchoff the tool beforeinsertion

To remove the battery cartridge, pullout

the

set

plate on the tool and grasp both

sides of the cartridge while withdrawing

from the barrel.

.To

insert the battery cartridge, align the

tongue on the battery cartridgewith the

groove in the housing and slip

into

place. Snap the

set

plate back intoplace.

sure to close the

set

platefully before

usingthe tool.

or removalof the batterycartridge.

not use force when insertingthe battery cartridge.

If the cartridgedoes notslide ineasily,

not being insertedcorrectly.

Charging

Plug the fast charger into your power

source. Insert the battery cartridge

that

the plus and minus terminals on the bat-

tery cartridge are on the same sides

their

respective markings on the fast charger. In-

sert the cartridgefully intothe port

that

rests on the charger portfloor.

The charging light will come on and charg-

ingwill begin. Ifthe charginglight does not

come on, press the reset button.

the

charging light goes out within

seconds even after pressingthe reset button

coupleof

times, the battery cartridge

dead. (CAUTION

Wait

for more than

seconds after the

charging light goes out to press the reset buttonagain.) Replace

with

new one. When

the charging light goes out after about one hour, you may remove the fully charged

batterycartridge.After charging, unplugthe charger from the power source.

CAUTION

Your new battery cartridge

notcharged. You will need to charge

beforeuse.

you try to charge

cartridge from

just-operatedtool, sometimesthe charging light

will not come on. If this occurs,

let

the cartridge cool off for

while. Then re-insert

and try tocharge

once more.

When you charge

new battery cartridgeor

batterycartridgewhich has notbeen used

for

long period,

may not accept

full charge. This

normal condition and does

not indicate

problem. You can recharge the battery cartridgefully after discharging

almost completely

couple

times.

If you wish tochargetwo battery cartridges, allow

minutesbetweenchargingson the

fast charger.

Switch action

Trigger

switch

Set

the reversingswitch lever just in front

of the trigger switch to Forward (FWD)

or Reverse

(REV).

Then pull the trigger

to turn the tool ON and release

toturn

OFF. To change the direction of bit

rotation, release the trigger,

let

the tool

come to

complete stop, and then slide

the switch lever tothe oppositeside. The

trigger switch does notwork if the switch

lever

inthe neutralposition.

Reversing switch lever

CAUTIONS:

Before insertingthe battery cartridge into the tool, always check to

see

that the trigger

When not operatingthe tool, keep the lever switch inthe neutralposition.

Before operation, always check to be sure that the switch lever

set

for the desired

Pullingthe trigger hardwhen the lever switch

set

to neutralcan cause switchbreakage.

switchactuates properlyand returnstothe

"OFF"

positionwhen released.

direction of rotation.

Fasteningtorque adjustment

The fasteningtorque may be adjusted by

turning the adjustment ring to align the

notched line on the ring with

number

on the indicator label. However, the

clearance between the ring and the cap

2.5

(1/8")

maximumafter one full

turn, and the ring should not be forced

beyondthis point.

Turning the adjustment ring in the arrow

direction obtains

higher torque

(HI

side); turning in the opposite direction

gives

lowertorque

(LOW

side).

Fasteningtorque

adjustment ring

Bit

.Aligning the notched line with the number

on the indicator label provides the right

torque for setting

(1/8")

screw. Aligning to the

and

suitable to drive

(3/16")

and

(1/4")

screw, respectively.

the adjust ring will not turn easily, switch the tool on and wait for the clutch to cut

inbeforemakingthe torque adjustment.

.To back out (remove)an already driven screw, use

little

moretorque than you used to

drivethe screw initially.

.Switch off

soon

the clutch cuts in. Continuous unnecessary clutchingwill loosen

the adjust ringand make

impossibletoobtain the desiredtorque.

Grip

.The grip

mended. shown on the right

recom-

Hole

0The hole on the heel

the tool

con-

venient way to carry

cord, hook

or other means.

Drillchuck (Accessory)

install

drill chuck, remove the insert

bit by

strongjerk, then

drill chuck can

be replaced with the insert bitby

sharp

push

the hand.

.To

install the drill bit, place

in the

chuck

far

will go. Tighten the

chuck collar

hand.

Place

the chuck

key in each of three holes, and tighten

clockwise.

remove the drill bit, placethe chuck key intothe chuck hole and turncounterclock-

wise.

CAUTIONS:

Be sure that the battery cartridge has been removedfrom the tool.

Always

set

the

Forward-Reverseswitch lever to

NEUTRAL

when installing, removing

or adjustingbits or accessories.

Screwdriving

Matchyour bittoyour screw.

Item

Rominal Diameter (mm)

Phillips bits

Select your screws

meter with the chart

Bit

No.

Wood

Screw

onandthenominalright. dia-

2.1

2.7

13/32''

118")

No.

3.1

4.8

(1/8"

3/16')

No.3

5.1

(3/16")

Slotted bits

Select

slotted bit to matchthe slot on the screw heads. Ifthe bit

too small for the

screw slot, the bitand/or screw head may be damaged.

This manual suits for next models

Table of contents

Popular Power Screwdriver manuals by other brands

Parkside

Parkside 345138 2004 instructions

AEG

AEG BST 18BLX2-0 Original instructions

Ingersoll-Rand

Ingersoll-Rand D5000 Series Product information

BGS technic

BGS technic 956 manual

Hilti

Hilti SD 6000 operating instructions

Parkside

Parkside PEPS 3 A1 Translation of the original instructions

Festool

Festool TI 15 operating manual

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Operation manual

Skil

Skil 2346 Operating/safety instructions

DeWalt

DeWalt XR LI-ION DCD931 user manual

Festool

Festool DWC 18-2500 operating manual

EINHELL

EINHELL TE-CD 12/1 Li Series Original operating instructions

Stanley

Stanley SCD2 manual

Atlas Copco

Atlas Copco LUM12 SR Product instructions

FAR

FAR TECNUM Original manual translation

GRAPHITE PRO

GRAPHITE PRO 59GP400 instruction manual

Festool

Festool C 12 Li instruction manual

Facom

Facom V.600R instructions