Make Noise XPO User manual
Stereo Prismatic Oscillator
(XPO)
2
XPO
Limited Warranty
Installation
*OUSPEVDUJPO
Panel Controls and Inputs/Outputs
Waveform Outputs
Frequency Controls
Timbre Controls
Tips and Tricks
Patch Corner
Table of Contents
3
4
5
6
7
12
14
15
16
3
Limited Warranty
Make Noise warrants this product to be free of defects in materials or construction for a period of one year
from the date of purchase (proof of purchase/invoice required).
Malfunction resulting from wrong power supply voltages, backwards or reversed eurorack bus board cable
connection, abuse of the product, removing knobs, changing face plates, or any other causes determined by
Make Noise to be the fault of the user are not covered by this warranty, and normal service rates will apply.
During the warranty period, any defective products will be repaired or replaced, at the option of Make Noise,
on a return-to-Make Noise basis with the customer paying the transit cost to Make Noise.
Make Noise implies and accepts no responsibility for harm to person or apparatus caused through operation
of this product.
or any needs & comments.
http://www.makenoisemusic.com
About This Manual:
Written by Walker FarrellBOE5POZ3PMBOEP
Illustrated by Walker Farrell and Lewis Dahm
XPO Hardware Design: Tony Rolando
Special Thanks to the Beta Testers!
4
-12V
Electrocution hazard!
Always turn the Eurorack case o and unplug the power cord before plugging or unplugging any Eurorack
bus board connection cable. Do not touch any electrical terminals when attaching any Eurorack bus
board cable.
The Make Noise soundhack XPO is an electronic music module requiring 140mA of +12VDC and 132mA of
-12VDC regulated voltage and a properly formatted distribution receptacle to operate. It is designed to be
used within the Eurorack format modular synthesizer system.
Go to http://www.makenoisemusic.com/ for examples of Eurorack Systems and Cases.
To install, nd 18hp of space in your Eurorack synthesizer case, conrm proper installation of included
eurorack bus board connector cable on backside of module (see picture below), plug the bus board
connector cable into the Eurorack style bus board, minding the polarity so that the RED stripe on the cable is
oriented to the NEGATIVE 12 Volt line on both the module and the bus board. On the Make Noise 6U or 3U
Busboard, the NEGATIVE 12 Volt line is indicated by the white stripe.
Please refer to your case manufacturers’ specications for location of the Negative supply.
Installation
5
Introduction
The XPO or Stereo Prismatic Oscillator is a Voltage Controlled Analog Oscillator designed for Stereo Timbre Modulations
(including Pulse Width Modulation and Wavefolding), Oscillator SYNC, Linear FM and more in the analog domain. It also
generates monaural Sine waves, Triangle waves, Sawtooth and Spike waves, and Sub-Octaves.
The XPO is designed as the Stereo VCO complement to our Stereo Quad core VCF QPAS, as is the core idea of complex circuits
being controlled in multiple dimensions in the stereo field by a few powerful parameters. The Stereo Prismatic Oscillator also
makes a particularly useful patch buddy for the STO, Mimeophon, and X-PAN.
The XPO yields harmonically rich textures through the use of Sync, Linear and Exponential FM, and especially several unique
forms of complex multi-dimensional Stereo waveshaping via the Modulate Left, Modulate Right, and Center parameters. All
outputs are available simultaneously, and all analog controls on the XPO are paired with control voltage inputs for full
integration into a modular synthesizer.
The XPO uses a Triangle Core and along the top you find individual Mono outputs for Sine, Triangle, Sawtooth, Spike, and
Sub-Oscillator. Along the right side there are three pairs of outputs forStereo Pulse-Width Modulation (PWM), Stereo Vari-
Timbre, and Stereo Wavefolding. The stereo outputs are controlled by two "Modulate" parameters for their Left and Right
outputs. Additionally the Vari-Timbre and Wavefolding outputs have a third timbre parameter called Center that modulates
left and right sides simultaneously another unique way.
The XPO has two identical 1v/oct inputs, a Sync input, an Exponential FM input with attenuverter, and a Linear FM input with
a Depth control and CV, as well as a normalization of the Sub oscillator waveform to the Linear FM input for easy "growl."
The XPO is a 100% analog musical instrument that is not suitable for laboratory use.
6
Panel ControlsBOE*OQVUT0VUQVUT
XPO Panel ControlsBOE*OQVUT0VUQVUs
1. Pitch control. Sets core frequency of the XPO.
2. Fine tune. Fine control of core frequency for tuning to other VCOs or instruments.
3. FM Input. Linear FM Input. AC Coupled. Normaled to Sub Output.
4. FM Depth CV Input. CV Input for FM Depth.
5. FM Depth Combo Pot. With nothing patched to FM Depth CV Input, sets FM Depth. With Signal
patched to FM Depth CV input, works as attenuator for that parameter.
6. Modulate-L Panel Control. Modulates Left Stereo outputs' timbre.
7. Modulate-L CV Input attenuverter. Bipolar input attenuverter for Modulate-L CV Input
8. Modulate-L CV Input. CV Input for Modulate-L. Also controls Modulate-R when Modulate-R CV Input is
unpatched.
9. V/Oct input (1). Sets core frequency of the XPO via external control, tracks one volt per octave.
Summed with Pitch control and V/Oct input (2).
10. V/Oct input (2). Sets core frequency of the XPO via external control, tracks one volt per octave.
Summed with Pitch control and V/Oct input (1).
11. Center CV Input. CV input for Center.
12. Center Combo Pot. With nothing patched to Center CV Input, sets Center parameter. With Signal
patched to Center input, works as attenuator for that parameter.
13. Expo FM Input attenuverter. Bipolar input attenuverter for Expo FM Input
14. Expo FM Input. Exponential FM input.
15. Modulate-R Panel Control. Modulates Right Stereo outputs' timbre.
7
Panel ControlsBOE*OQVUT0VUQVUT (cont.)
16. Modulate-R CV Input attenuverter. Bipolar input attenuverter for Modulate-R CV Input.
17. Modulate-R CV Input. CV Input for Modulate-R. Normaled to Modulate-L CV Input.
XPO Panel ControlsBOE*OQVUT0VUQVUs (Cont.)
8
Panel ControlsBOE*OQVUT0VUQVUT (cont.)
XPO Panel ControlsBOE*OQVUT0VUQVUs (cont.)
1. Sine output. ~10V peak to peak.
2. Triangle Output. ~10V peak to peak.
3. Sawtooth Output. ~9V peak to peak.
4. Spike Output. ~12V peak to peak.
5. Sub Output. ~12V peak to peak.
6. Sync Input. Expects audio rate modular synth waveform.
7. Pulse Width Modulation Left (Mono) output. 8-12 V peak to peak, amplitude varies based on
Modulate controls.
8. Pulse Width Modulation Right output. 8-12 V peak to peak, amplitude varies based on Modulate
controls.
9. Vari-Timbre Left (Mono) output. 8-12V peak to peak, amplitude varies based on Center and
Modulate controls.
10. Vari-Timbre Right output. 8-12V peak to peak, amplitude varies based on Center and
Modulate controls.
11. Wavefolding Left (Mono) output. 8-12V peak to peak, amplitude varies based on Center and
Modulate controls.
12. Wavefolding Right output. 8-12V peak to peak, amplitude varies based on Center and
Modulate controls.
9
The Waveform Outputs
Mono Outputs
Along the top of the XPO are five Mono wave shape outputs that are derived from the oscillator core.
The Sine wave is shaped from the Triangle using the same circuit used on the DPO and STO. The Sawtooth, Spike, and Sub
outputs are new for XPO. These outputs are useful on their own as traditional VCO outputs to be processed via VCAs, filters etc.
Using mixers such as Optomix or X-PAN they could be mixed together and/or panned alongside your choice of stereo outputs,
and they can also be very useful as modulation sources for timbral controls on the XPO itself (Center, Modulate, etc.) or for
audio rate modulation on processors such as QPAS, especially when said processors are also operating on outputs from the
XPO itself, which will always represent at the same frequency at every output.
The Sine Wave is derived from the Triangle core of the oscillator and is provided as an output because it is great for
blending with signals of greater harmonic content in order to strengthen the fundamental. The Sine shape has
almost no harmonics, so it is also a good starting point for creating complex FM sounds because the sidebands
introduced through FM are not obscured by harmonics present in the signals utilized.
The Triangle Wave is the core shape of the oscillator. It contains slightly more harmonic content than the sine wave
and also a strong fundamental, and will cut through a mix slightly more than a sine wave. It can be a useful
modulation source where you want more harmonics created, for example audio rate modulation of Filter Cutoff.
The Sawtooth Wave is a classic bold East Coast synthesis waveform that is frequently utilized in subtractive synthesis,
as it contains all harmonics and provides a rich source for being shaped with filters.
The Spike Wave is a thin, tall spike shape with low fundamental presence resulting in a thin, “buzzy” sound. This less
common waveform can be found in the seminal West Coast “Music Easel” synthesizer. It is useful for adding or
subtracting a strong harmonic from a less harmonic waveform such as triangle. It is also a useful shape for
modulation especially destinations that have the potential for "ringing" such as resonant Filters.
Sub Oscillators are a classic Far East Coast waveform that have been used to thicken up the sound when mixed with
other waves from the same VCO. The Sub Waveform output on the XPO contains a mix of multiple Square waves
derived from the oscillator core at lower octaves (sub-harmonics). , This output is a good candidate for subtractive
synthesis with filters. It is great for basslines and other “fat” sounds, but it is also an excellent Modulation source.
Patched to the Filter Cutoff of QPAS it will super-impose sub-harmonics that make the filter growl.
Another version of the Sub Wave is also normalized to the XPO’s Linear FM input. With nothing patched to this input,
FM Depth can be used as an additional voltage controlled timbre parameter with the result being sub harmonic FM.
10
The Waveform Outputs (cont.)
Stereo Outputs
Along the right side of the XPO are three pairs of Stereo outputs that are derived from the oscillator core. These
outputs provide great audio sources for stereo processing modules such as QPAS or Mimeophon. All three output pairs
receive timbral modulation from the Modulate L/R parameters, and can be used in Mono via their Left output when the
Right is unpatched. Additionally the Vari-Timbre and Wave Foldingoutputs receive timbral modulation from the Center
parameter on both outputs at once.
The Pulse Width Modulation outputs utilize a classic PWM circuit to modulate the width of a
pulse wave continuously from 0% (silence) at full CCW on the Modulate controls, to 50%
(square wave) around 12:00, to ~99% (a very thin pulse) at full CW. Using control voltage, the
pulse-width can be increased all the way to 100% (silence again).
Pulse width modulation tends to create alternate sets of even and odd harmonics. Since the XPO offers two independent PWM
parameters on the two outputs, interesting combinations can be heard when monitoring in stereo and modulating both sides
simultaneously at the same or different rates and amounts.
The Left and Right PWM outputs are controlled independently by the Modulate controls. When the Right output is unpatched,
the Left output contains a sum of the Left output and an inverted copy of the Right output. Using just the Left output in this
case for a Mono signal allows for interesting phasing behaviors when modulating one or both waves.
Table of contents
Other Make Noise Recording Equipment manuals
Make Noise
Make Noise Rene User manual
Make Noise
Make Noise MATHS User manual
Make Noise
Make Noise Rene User manual
Make Noise
Make Noise RxMx User manual
Make Noise
Make Noise MATHS User manual
Make Noise
Make Noise 7U 4 ZONE CV BUS CASE User manual
Make Noise
Make Noise DPO User manual
Make Noise
Make Noise modDemix User manual
Make Noise
Make Noise PHONOGENE User manual
Make Noise
Make Noise 0-CTRL User manual
