MADRIX STELLA User manual
STELLA
Technical Manual & Quick Start Guide
1EN
MADRIX®STELLA –
Technical Manual & Quick Start Guide
6th Edition — December 2021
Thank you for purchasing MADRIX®STELLA!
Please read this manual carefully and thoroughly before using MADRIX®
STELLA. Make sure that you fully understand all information.
This MADRIX®STELLA Technical Manual is written in English and German.
(Dieses Handbuch wurde in englischer und deutscher Sprache verfasst.)
Developed and made in Germany.
Imprint
Managing Directors: Christian Hertel, Sebastian Pinzer, Sebastian Wissmann
Trademark Credits
Microsoft®and Windows®are U.S. registered trademarks of Microsoft
Corporation.Art-Net™–DesignedbyandCopyrightArtisticLicenceHoldingsLtd.
All other products mentioned herein may be trademarks of their respective
companies.
MADRIX®is a registered trademark of inoage GmbH.
inoage GmbH
Wiener Straße 56
01219 Dresden
Germany
Web www.madrix.com
E-mail [email protected]
Phone +49 351 862 6869 0
EN 2
English
Copyright Information And Disclaimer
© 2021 inoage GmbH. All rights reserved.
Information is subject to change at any time and without prior notice. Errors and
omissions excepted. Reproduction, adaptation, or translation without prior
written permission is prohibited. inoage GmbH does not grant guarantee on
validity for a particular reason, the marketability, or other properties of the
product. There is no way to assert a claim to inoage GmbH, neither in the legal
way nor in other ways. inoage GmbH is not responsible for damages, including all
disadvantages that are not just limited to the loss of sales, but that are caused
due to the use of the product, due to the loss of serviceability of the product, due
to misuse, happenings, circumstances, or actions that inoage GmbH does not
have influence on, no matter if the damages as well as consequential damages are
direct or indirect; whether they are special damages or others, nor if the damage
is caused by the owner of the warranty or a third person.
Limited Warranty
Fiveyearsof limited manufacturer'swarrantyare granted to thepurchaser ofthis
product with regards to constructional fault, material defect, or incorrect
assembly the manufacturer has caused or is to be held responsible for.
This warranty will be void if the interface is opened, modified, or damaged through
inappropriate handling, wrong usage, overvoltage, or damaged through any other
cause. All details are available online at www.madrix.com/warranty
Package Contents
1x MADRIX®STELLA
1x Set of pluggable screw terminals (2x 3-pin and 1x 2-pin)
1x USB 2.0 cable
(certified)
2x Wall-mount brackets
1x This technical manual / quick start guide
Please note: Check the package contents and the condition of the interface
after unpacking! Contact your supplier if something is missing or damaged. Do
not use the device if it seems to be damaged!
3EN
Beware that the interface works with electrical power. Only use the
device in dry environments (indoor use). The IP Rating of the device
is IP20. Do not use the interface in humid environments and avoid
contact with water or any other liquids. Turn off the power if you are not using
the device for a long time.
It is recommended to always use galvanic isolation (e.g. an opto-isolator/opto-
coupler splitter). Avoid unwanted voltage on the DMX lines/cables at all times.
Do not remove any parts from the unit or connect to an ungrounded circuit. Do
not connect the unit to LEDs that are switched on. Only connect the unit to DMX
fixtures and controllers that are initially powered off.
There are no user serviceable parts inside or outside the interface. Repair service
lies only within the responsibilities of the manufacturer. If the interface appears
to be defective, please contact your dealer. After expiration of the warranty
period, you may contact your supplier or the manufacturer to have the unit
repaired against payment of an individual service fee if possible.
The interface has several ports and slots. Only connect or insert devices, cables,
andconnectorstotheindividualportsandslotsusingconnectorsofthesametype
as the port. Do not use inapplicable equipment. This device should be used by
professionals. The device is not designed to be operated by non-professionals or
children.
Recommendation: DIN-Rail Power Supply 12 V (MEAN WELL HDR-15-12,
DC Output, 12 V, 1.25 A, 15 W, 1 SU, DIN Rail) / Order Number: IA-HW-001027.
Safety Instructions
Please follow the instructions below to avoid mishandling, damage to the
device, or personal injury:
THE DEVICE WORKS WITH LOW VOLTAGE (DC 5 V – 24 V).
DO NOT USE ANY OTHER VOLTAGE!
External USB power supplies: Using non-permissable units
poses risk of fire. 5.5 V⎓500 mA max. output is allowed.
Any connected external power supply needs to be fused
according to its output and/or short-circuit proof.
In order to cut off the supply of power completely, you need to
disconnect any external power-supply unit as well as USB.
EN 4
English
End-Of-Life
This electrical device and its accessories need to be disposed of
properly. Do not throw the device into normal trash or household
waste. Please recycle packaging material whenever possible.
Technical Specifications
Supply Of Power:
Power Consumption:
Network Protocols:
RDM Role:
DMX512:
Ports:
Ethernet:
Ethernet Switch:
USB:
Handling:
Case:
Dimensions:
Weight:
Temperature Range:
Relative Humidity:
IP Rating:
Certificates:
Warranty:
DC 5 V – 24 V; over
A) 2-pin, pluggable screw terminal or B) 5 V USB
< 1.5 W (300 mA) during normal operation (500 mA max. fused)
Art-Net (I, II, 3, 4, incl. ArtSync), Streaming ACN (sACN / ANSI E1.31)
Transmits commands and requests to RDM Responders and
back (Art-Net Node / RDM Controller)
2x 512 DMX channels, input and/or output (Automatically per port)
2x ports (Via 2x 3-pin, pluggable screw terminals)
2x RJ45, Auto MDI-X, daisy-chain support, 10/100 MBit/s
(Compatible with 1 GBit/s)
Lookup Table (ALU) for 1024 unicast MAC addresses
1x port, USB 2.0, type-B female socket
5 status LEDs (+4 network status LEDs)
Non-conductive, V-0 flammability rating (UL94 test method),
designed for 35 mm DIN-rails or wall mounting
90 mm x 70 mm x 46 mm (Length x Width x Height)
108 g | 125 g incl. screw terminals and wall mounts
-10 °C to 70 °C (Operating) | -20 °C to 85 °C (Storage)
5 % to 80 %, non-condensing (Operating / Storage)
IP20
CE, EAC, FCC, RoHS
5 years of limited manufacturer's warranty
Usage
In general, this device is designed to be operated as a hardware control interface
to be connected towards various types of controllable lights / lighting controllers
via DMX512 by using USB or Art-Net / Streaming ACN over Ethernet.
Do not use the interface for any other, deviating purpose.
The device can be connected to and disconnected from USB or Ethernet network
during use and without a reboot (Hot Swapping & Plug and Play). Multiple
interfaces can be used at the same time.
5EN
IP Address And Other Device Information
You will find the following important information on the side of the device:
�Serial number ('Serial')
�Hardware revision ('Model')
�Default and pre-configured IP address ('Default IP')
(See p. 10 to reset the device to the default IP address if needed.)
Compatibility
MADRIX®STELLA is a standard network node for Art-Net or Streaming ACN.
You can use the device with any compatible software, console, or controller.
See chapter 'Technical Specifications' on p. 4 for detailed information.
Using The MADRIX®5 Software
MADRIX®5 is a professional and advanced LED lighting control software. It
supports Art-Net and Streaming ACN; among many other communication
protocols. Itisrecommendedforusage in combinationwith MADRIX®STELLA,but
only required if you would like to send or receive data over USB.
For more information about MADRIX®5, including its minimum system
requirements and supported operating systems, visit the website
www.madrix.com
Please note: In order to send out data via MADRIX®STELLA using
MADRIX®5, a MADRIX®5 software license is required (sold separately)!
Daisy-Chain Support
MADRIX®STELLA features 2 separate Ethernet network ports. Either one is fully
functional for IN and OUT and can be used for the data connection without using
a separate network switch or router. We recommend to connect a maximum of
40 units after one another in a row, when using Art-Net in Unicast Mode or
Streaming ACN Multicast at a max. data rate of 50 FPS / 20 ms without any
additionaldevicesinthenetwork.InMADRIX®5,wehighlyrecommendtoactivate
ArtSync for excellent image quality (see p. 13).
EN 6
English
Connectivity
1) Power
2) Right Ethernet port,
incl. 2 status LEDs
3) Left Ethernet port,
incl. 2 status LEDs
4) USB port
5) Status LED for Power
6) Status LED for USB
7) Status LED for DMX 1
8) Status LED for DMX 2
9) DMX 1
10) Reset button
11) DIN-rail unlocking clip
12) DMX 2
GROUND
DMX –
DMX +
GROUND
DMX –
DMX +
9
5
1
3
4
12
10
11
6
7
8
2
Please note:
Thepackagecontentsdo
not include network
cables, power cables, or
DMX fixtures.
2x Mounting Brackets:
Put each bracket in the
pre-drilled holes on the
device's left and right side.
Safely secure the
assembled unit only on
solid surfaces using
screws with Ø=3.5 mm.
7EN
1) Connecting Your Lighting Fixtures
See chapter 'Connection Diagram Variations' on p. 8 for all possible variations.
Step 1) Completely switch off your supply of power before connecting your
DMX fixtures to the device!
Step 2) Connect your DMX fixtures to the provided 3-pin screw terminals:
Step 3) Plug the 3-pin screw terminals into the device. The screws must face
upwards.
Step 4) Supply your DMX fixtures with power.
Step 5) Continue with '2) Connecting To Power And Data' below.
2) Connecting To Power And Data
See chapter 'Connection Diagram Variations' on p. 8 for all possible variations.
Step 1) Be careful when handling the device and electrical power! Completely
switch off your supply of power before connecting to the device!
Step 2) Connect your power cables to the provided 2-pin screw terminal:
Step 3) Plug the 2-pin screw terminal into the device. The screws must face
upwards.
Step 4) Connect to USB or to Ethernet network for data as required.
Step 5) Do not switch on your supply of power until all required power cables
and DMX fixtures are connected to MADRIX®STELLA.
» Make sure to choose cable lengths according to the DMX specifications.
» You may connect only to DMX 1, only to DMX 2, or to DMX 1 and DMX 2.
» Pay attention where to connect GROUND, DMX –, and DMX +; as
indicated on the device.
» Insert each individual wire consecutively and tighten the corresponding
screw with a suitable screw driver.
» Pay attention where to connect + and –; as indicated on the device.
» Insert each individual wire consecutively and tighten the corresponding
screw with a suitable screw driver.
EN 8
English
Connection Diagram Variations
Network Data
Power
Variation A
USB Power
Network Data
Variation B
Power
USB Data
Variation C
USB Data & Power
Variation D
9EN
Device Configuration Through A Web Browser
Step 1) Connect MADRIX®STELLA and your computer to the same network.
Step 2) Assign correct network settings for your computer in the operating
system. (Recommended default settings:
IP address 10.0.0.1 and Subnet mask 255.0.0.0)
Step 3) Open your web browser and enter the IP address of MADRIX®STELLA.
(You can find the default IP address on the side of the device.)
Step 4) The built-in web configuration tool will be launched.
Step 5) Change any settings as required. Apply changes with 'Set'.
MADRIX®HARDWARE MANAGER
Step 1) Connect devices to your computer over USB or network, but not both!
Step 2) Make sure to stop sending control data to the devices!
Step 3) Start the MADRIX®HARDWARE MANAGER Software.
Step 4) In MADRIX®HARDWARE MANAGER, go to the tab 'Devices' and
confirm or change the network settings and any other settings for your
devices as required.
On a selected device, use Right Mouse Click > 'Open Device
Configuration Via HTTP...' to open the web configuration through a
web browser, as explained above.
On a selected device, use Right Mouse Click > 'Restore Factory
Default Settings' to perform a reset to factory default settings.
For more information, see the MADRIX®HARDWARE MANAGER User Manual.
The software is available for download from www.madrix.com
Remote Device Management (RDM)
In order to use RDM, call up the built-in web configuration (see above) and go to
'Network To DMX Output' > 'Enable RDM' for ports 'DMX 1' and/or 'DMX 2'.
Make sure to disable RDM on the specific port, when using STELLA for DMX-IN.
Thanks to STELLA's Packet Multitasking, RDM and Art-Net can be sent and
received at the same time and during live operation with a min. frame rate of 22
FPS, an expected average of 34 FPS, and a max. frame rate of 44 FPS, depending
on the number of RDM packets.
Other manuals for STELLA
4
Table of contents
Languages:
Other MADRIX Cables And Connectors manuals
