Macro CXW-300-T2C User manual
1
User Manual for Range hood
Model Name: CXW-300-T2C
This product implements national standards:
GB 4706.1 2005
GB 4706.28 2008
GB 29539-2013
GB/T 17713-2011
Content
1. Safety Precautions Safety precautions.................................................. 2
2 . Important Information...........................................................................4
3. Product Information............................................................................... 4
4. Installation Instructions..........................................................................6
5.Instructions for operation..................................................................... 11
6. Maintenance..........................................................................................12
7 .Troubleshooting.................................................................................... 13
8. After-sales Service.................................................................................14
2
1. Safety Precautions Safety precautions.
In order to avoid harm and property damage to users and other personnel, please carefully read
the following important safety matters, please strictly abide by, and on the basis of full
understanding of the content of the correct use. Before use, please read this manual carefully
and use in strict accordance with the instructions. In case of any personal injury or property loss
caused by improper use of this product, the Company shall not assume any legal liability.
Interpretation of signs
Forbidden Sign
Do not operate
Warning Sign
Should strictly follow the
requirements
Attention Sign
The part that must be paid
attention to
Forbidden
Do not disassemble, install, or maintain the range hood for non-professional personnel.
Non-professional maintenance personnel are absolutely prohibited to change the internal
wiring of range hood without permission.
Do not touch the power plug, electrical parts and power switch with wet hands. Otherwise,
electric shock may occur.
The fire should be put out in time when not in use. It is forbidden to bake the range hood
directly by the fire, and make it hot and dangerous.
Do not allow unsupervised children and the weak to use the range hood alone, otherwise it
may lead to electric shock or other accidental injury.
Do not modify, stretch, tie, or press the power cable. Otherwise, the power cable may be
damaged and electric shock or fire may occur.
Do not allow electrical parts such as motors, switches and connectors to get wet with water.
Do not flush the range hood with water. Do not use the range hood when it is wet with
water. If used, it will lead to electric leakage, electric shock and other accidents.
Warning
3
Before cleaning range hoods and providing installation or maintenance services, disconnect
the power supply to avoid electric shock.
The exhaust gas from the range hood should not be discharged into the hot pipe used to
discharge the smoke from burning gas or other fuels.
When a range hood is used in conjunction with an appliance that burns gas or other fuel,
the room must be well ventilated.
If not cleaned according to the instruction manual, the range hood has the risk of fire.
To avoid injury, do not put your fingers or other objects into the moving parts of the range
hood.
When the oil pan is on fire, please turn off the range hood immediately and use effective
extinguishing methods to extinguish the fire, such as covering the open flame with a metal
lid, closing the main gas valve immediately, and keeping combustible materials away from
the open flame.
Attention
The range hood should use a special power socket, and the special power socket should be
reliably grounded.
The ambient temperature of the range hood cannot exceed 40 °C.
Exterior parts (such as decorative sealing plates) are covered with protective films. Remove
them carefully before use.
If the power cable is damaged, it must be replaced by professionals from the manufacturer,
maintenance department or similar departments to avoid danger.
This appliance is an outdoor range hood, and the lampblack is discharged to the outside
through the smoke pipe. Please ensure that the exhaust pipe is smooth, so as not to affect
the smoke exhaust effect.
The installation shall be carried out by professional personnel. After the installation and test
run, the after-sales service personnel shall explain the use method to the user while there is
no abnormal phenomenon.
If you need to clean the inside of the range hood, please contact Macro after-sales
personnel for professional cleaning.
If need to use the AC power of more than 220V, please confirm with supplier for safety
issue.
4
2 . Important Information
If the range hood is not in use for a long time, remove the power plug from the socket.
When installing a new range hood, if the accessories do not conform to the instructions,
contact your local dealer or service center immediately. Please dispose of recyclable
packaging materials in an environmentally friendly manner to maintain a good environment.
Do not allow children to play with plastic film and packing cases, this may cause room
accidents, so please keep packaging materials away from children, packaging materials are
not toys.
Disposal of old range hoods
When the old range hood cannot be used, cut the power cable so that it cannot be powered
on. Old range hoods contain reusable materials. Please help to dispose or recycle them to
make a contribution to environmental protection.
Before using a new range hood
If the range hood is obviously damaged, do not install it. Contact your local dealer or service
center immediately.
To ensure that you can use the range hood correctly and safely, please read the manual
carefully before using the range hood and strictly follow the precautions in the manual.
3. Product Information
List of machine and accessories
The range hood is equipped with the following accessories, please check and accept them when
unpacking.
No.
Name
Quantity
No.
Name
Quantity'
1
Range hood
1
7
Limit screw M5x 12
1
2
Instruction manual
1
8
Chimney pipe Φ180x1800
1
3
Hanging panel
1
9
Plastic expansion tube Φ8x
60
4
4
Oil cup
1
10
Cross recessed tapping screws
ST2.9x8
2
5
Air Damper assembly
1
11
Wood screw M5x 60
4
6
Aluminium foil paper
1
12
5
Main Technical Data
Name of Product
Range hood
Product Model Number
CXW-300-T2C
Rated voltage
220V~
Rated frequency
50Hz
Rated input power of main motor
300W
Maximum lighting power
2W
Rated input power of the device
302W
Power of cleaning
360W
Air volume
18m3/min
Wind pressure
320Pa
Maximum static pressure
420Pa
Noise
69dB(A sound power level)
Energy efficiency rating
Level 1
Normal odor reduction degree
95%
Instantaneous odor reduction
50%
Degree of oil separation
86%
Full pressure efficiency
24%
The net weight
16.5 kg
Gross weight
21.5 kg
Product size
895mm x 450mm x 600mm
Product package size
1010mm x 670mm x 553mm
Note:
1. In the "clean" mode, the maximum air volume is 20m /min.
2. The allowable difference between the measured value of air volume, air pressure and
maximum static pressure and the expressed value shall not exceed -10% of the expressed value;
3. The noise value shown is the sound power level of weight A, and the sound pressure level
noise is the sound power level of weight A -14dB;
4. The above data are measured according to standard test methods under environmental
conditions stipulated by national standards;
5. If there is a slight deviation between the express value and the actual size, the measured value
shall prevail;
6
4. Installation Instructions
Installation precautions
★Special note: Macro products must be installed and maintained by our authorized installation
and maintenance service providers, otherwise we will not be responsible for the accidents
caused by installation and maintenance.
If your kitchen is under renovation, do not expose the range hood, because construction
materials, dust, paint, coatings and the gas they volatilize will corrode the surface of the
range hood, and thus make the surface tarnish. Therefore, it is recommended that you
install the range hood after the decoration is completed.
Install the range hood on a non-flammable wall with sufficient supporting strength that can
bear more than three times the weight of the range hood.
To ensure the safety and smooth installation, please use the accessories delivered with the
installation (especially plastic expansion tube and wood screw); When installing an
expansion tube, ensure that the expansion tube is closely matched with the wall holes. Do
not drill too large holes to prevent the expansion tube from loosening and causing
accidental fall.
Do not install the range hood in the bathroom or a place with high humidity. It may cause
electric shock.
When installing the lampblack machine, do not contact the steel bars in the building with
wood screws.
If the range hood is installed above the gas range, the distance must be at least 650mm. For
details, see the procedure for installing a range hood.
The width of the stove should not be larger than that of the range hood.
The range hood is a household appliance, not suitable for industrial and commercial use,
avoid use in special environment.
In case of gas leakage, do not use the range hood; otherwise, there is a risk of fire.
If you do not use the lampblack machine for a long time, unplug the power or turn off the
switch on the socket.
If you need to connect the smoke pipe directly to the public flue, do not insert the smoke
pipe too deep into the public flue to avoid affecting the smoke exhaust effect.
If you connect the pipe directly to the outside, extend the pipe at least 30mm out of the wall,
and the outlet should be slightly downward to avoid rainwater backpouring.
The relevant laws on emissions must be observed
7
Name of main parts
Preparing for Installation
The surroundings
The range hood should avoid being installed in too many doors and Windows, forming too
much air convection, and affecting the effect of lampblack removal.
Preparing Tools
Before installing a range hood, prepare the following tools:
1. Impact drill (with drill bit) 2. Screwdriver 3. Tape measure
Preparation of attachments
Accessories should be prepared when installing the range hood (see attachment list)
Installation diagram
The distance between the air outlet and the exhaust hole of the range hood should not be
too long. It should be less than 1.5m, and the number of turns should not be more than 2.
As with the cabinet, its installation diagram is shown in Figure 2.
8
Mounting size drawing
Installation dimensions are shown in Figure 3.
9
Opening size of Cabinet or ceiling for chimney pipe
The size of the cabinet or ceiling smoke pipe is shown in Figure 4.
Installation Procedure
Mounting plate
As shown in Figure 5, accurately determine the mounting holes for the hanging plate at
corresponding positions on the wall, drill the mounting holes in the holes with a drill bit,
firmly bury the plastic expansion tube, and then tighten the wooden screws.
Install the check valve(air damper) assembly
As shown in Figure 6, remove the large flat-head screws with cross grooves from the air
outlet holes on the container, and secure the check valve to the container with screws to the
holes in the check valve assembly and the check valve gasket.
10
Installing a chimney pipe
Insert the pipe into the check valve as shown in Figure 7, then lock it with the self-tapping
screw and wrap it with the aluminum foil.
Mounting the body
Lift the whole machine as shown in Figure 8. The mounting holes on the back of the box are
aligned with the hooks on the mounting plate. Then, fix the limit screws in the accessory bag
to the limit holes on the mounting plate to prevent the lampblack from falling accidentally.
Install oil cup
Push the oil cup in along the oil cup hanging ear.
Table of contents
