M-system 17PE User manual

17PE

P. 1 / 2EM-2938

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

COMPONENT IDENTIFICATION

Body

Specifications

Front Cover

(Connection diagram

behind)

■FRONT PANEL CONFIGURATION (with the cover open)

Span Adj.

Zero Adj.

INSTALLATION

Use Standard Rack (model: 17BXE).

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System's Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Signal conditioner ....................................................(1)

■ MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, including installation, connection and basic

maintenance procedures.

POINTS OF CAUTION

■ POWER INPUT RATING & OPERATIONAL RANGE

24 V DC ±10%, approx. 35 mA

■ REMOVING THE UNIT

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 40 to 85% RH in

order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is supplied,

however, a warm up for 10 minutes is required for satisfying

complete performance described in the data sheet.

PT TRANSMITTER MODEL 17PE

INSTRUCTION MANUAL

17PE

P. 2 / 2EM-2938

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram behind the front cover.

■ DIMENSIONS mm (inch)

110 (4.33 )

93 (3.66)

24 (.94)

7 (.28)

78 (3.07)32 (1.26)

8–M3.5

SCREW

7 (.28)

2–M3

SCREW

■ CONNECTION DIAGRAM

LOAD

SOURCE

FUSE

OUTPUT

AUXILIARY

POWER

CONNECTOR

■ TERMINAL ASSIGNMENTS

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Auxiliary power supply voltage: Check voltage supplied to

the rack (model: 17BXE). Use a power source of ripple

level 10% p-p or less.

3) Input: Check that the input voltage is within 0 – 120%

of the rated voltage.

4) Output: Check that the load resistance meets the described

speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered speci-

ﬁcations, therefore you usually do not need any calibration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■ HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the auxiliary power supply on and warm

up for more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above procedure

1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■ CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accuracy

described in the data sheet. When the output is out of toler-

ance, recalibrate the unit according to the "ADJUSTMENT

PROCEDURE" explained earlier.

LIGHTNING SURGE PROTECTION

In order to protect the unit from lightning surges entering

through signal and power supply cables, use of appropriate

lightning surge protectors are recommended. Please contact

M-System.

Other M-system Transmitter manuals

M-system

M-system B5VS User manual

M-system

M-system M5CT-5AM User manual

M-system

M-system Mini-M M2YV User manual

M-system

M-system F2VF User manual

M-system

M-system WRS2 User manual

M-system

M-system M6DVF User manual

M-system

M-system M3SMS User manual

M-system

M-system F2MS User manual

M-system

M-system Mini-M M2XR2 User manual

M-system

M-system M1EXV-4 User manual

M-system

M-system M3LT User manual

M-system

M-system W5 Series User manual

M-system

M-system Mini-M M2CEC User manual

M-system

M-system Mini-M M2VF2 User manual

M-system

M-system Mini-M M2XUM User manual

M-system

M-system W5PA User manual

M-system

M-system Mini-M M2TT User manual

M-system

M-system W5MS User manual

M-system

M-system Mini-M M2VF User manual

M-system

M-system Mini-M M2RS1 User manual

M-system

M-system M3SXT User manual

M-system

M-system LC User manual

M-system

M-system CTS2 User manual

M-system

M-system KCEC User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction