Lynx L36 Series User manual
LCB2-3 INSTALLATION INSTRUCTIONS
TOOLS REQUIRED: 7/16 Wrench
CONTENTS OF KIT: An adjustable side burner mounting bracket
Side shelf mounting bracket with 7/16 fasteners
Decorative cover for the L27 and L36 models
The side burner support bracket comes preassembled for the L27 and L36
Lynx Grills, 7300 Flores St., Downey, CA 90242
Customer Care Ph.: 888-289-5969/ Fax: 562-299-6978/Service@lynxgrills.com
P/N 34912 8/14
INSTRUCTIONS FOR MODELS L36 and L27:
1. Remove the right hand side shelf and the cabinet back panel (fig. 1)
2. Mount the LCB2-3 side burner to the supports (fig. 2)
3. If needed, any misalignment can be corrected by 1st measuring the amount of misalignment, 2nd loosening the
bracket support fasteners. 3rd raise or lower the bracket according to your measurements.
Tighten the fasteners. (fig 3)
4. Hang the side shelf removed in step 1 on the right side shelf support pins of the side burner (Fig. 6, pg. 2)
P/N 34912. 8/14
Rear View
12
3
INSTRUCTIONS FOR MODELS L54, L42, L30:
1. Remove the right hand side shelf. See fig.1 on page 1
2. At the rear, remove the decorative cover (1) on the left hand side of the LCB2-3 by removing the Philips head screw
and sliding it out. This also gives access to the gas piping connections. (Fig. 2)
3. Locate the mounting bracket on the inner most bracket support (Fig 3). Remove the 7/16 fasteners holding it in
place Reinstall the mounting bracket on the rear most bracket support and secure it with the 7/16 fasteners
4. As in step 3 on page 1,correct any misalignment in the shelf
5. Move the shelf mounting bracket on the right hand side, to the outermost mounting holes using the 7/16 nuts, and
tighten. (Fig. 5)
6. Hang the side shelf removed in step 1, pg. 1 to the right side of side burner on the shelf mounting bracket pins
(Fig 6)
2
Remove the bracket from the inside
support and install it onto the outer
support
3
5
This bracket must be mounted in the outer
position
6
Once the side burner is mounted to the grill the gas con-
nections can be made. Refer to the illustrations on the
right for proper gas installation examples.
After the side burner gas connections are made it is rec-
ommended that a leak test be done on all gas line fittings.
Apply a soap and water solution to all connections and
look for bubbles to form which indicate a gas leak. If no
bubbles are present, make the electrical connections
The side burner is electrically connected to grill at the
transformer. Disconnect the transformer from the grill
and plug in the side burner as shown in the illustration
below.
Finished Dimensions
This manual suits for next models
2
Table of contents
Other Lynx Grill manuals
Lynx
Lynx ASADO L30AGF User manual
Lynx
Lynx L27-2 User manual
Lynx
Lynx SMART30F User manual
Lynx
Lynx L30 Series User manual
Lynx
Lynx L42R1NG User manual
Lynx
Lynx L27-2 User manual
Lynx
Lynx L27 Series Installation manual
Lynx
Lynx L30PSR Guide
Lynx
Lynx SEDONA L700FNG User manual
Lynx
Lynx ALL-TRIDENT L30ATR User manual
Popular Grill manuals by other brands
Kenmore
Kenmore 415.16123800 Use and care guide
Camp Chef
Camp Chef PG24CLAU Warning & instruction booklet
Tucker Barbecues
Tucker Barbecues GTR Series Assembly, installation and operating instructions
Monogram
Monogram ZGG540NCP1SS owner's manual
Equipex
Equipex Sodir Savoy Operation manual
Gaggenau
Gaggenau VR 414 610 use and care manual
