LuxaFlex PowerView Motorisation User manual
PowerView®Motorisation
Smart shades that simplify your life
Quickstart guide
Scene
The Art of Window Styling
A brilliant evolution
in The Art of Window Styling.
3
COMPONENTS
This guide will help you get started with your PowerView®
purchase.
STEP 1 INSTALL YOUR SHADES
Make sure you have properly installed your shades and that
they are connected to a power source (battery pack or power
supply).
STEP 2 YOUR POWERVIEW®
COMPONENTS
Packed with your purchased product you will find one or more
Remotes, repeaters and a Hub (which is optional and only
required when you want to control your shades using a tablet
or smartphone). Remotes come in different shapes and colours.
Please locate them all before you start.
Pebble® Remote
Wall Surface
Repeater (optional)
Hub (optional), required for controlling your shades
with a tablet or smartphone.
4
PAIRING REMOTES
STEP 3 PAIRING REMOTES
If you only have one Remote, please proceed to Step 4.
By pairing PowerView® Remotes you make all your Remotes
part of the same PowerView® Network. This is important for
seamless installation of the PowerView® system.
For this instruction you use the STOP button on your
Remote.
3.1 TAKE ALL REMOTES
NAME 1 REMOTE“SOURCE”
NAME THE REST OF THE REMOTES
“TARGET”
REPEAT THE FOLLOWING STEPS
UNTIL ALL “TARGET”REMOTES HAVE
BEEN SET
Stop
TargetSource Target
5
”TARGET” REMOTE:
3.2 PRESS THE RESET BUTTON FOR SIX
SECONDS
Using a paper clip, PRESS and HOLD recessed Reset
button on back of target remote for 6-10 seconds.
If necessary, remove back cover.
”TARGET” REMOTE:
3.3 CLOSE THE COVER IF NECESSARY
”SOURCE” REMOTE
3.4 PRESS STOP FOR 6 SECONDS
(Keep pressing until the Remote lights start blinking).
”TARGET” REMOTE:
3.5 PRESS STOP AND HOLD
“SOURCE” REMOTE
3.6 PRESS STOP AND RELEASE
PAIRING REMOTES
reset button
”TARGET” REMOTE:
3.7 RELEASE STOP
(As confirmation “TARGET”Remote will flash the group buttons).
”TARGET” REMOTE:
3.8 IF THE BUTTONS ARE STILL FLASHING PRESS STOP FOR
6 SECONDS
(Keep pressing until the flashing stops).
PAIRING REMOTES
6
STEP 4 ADDING A SHADE TO
A REMOTE
A Remote can control 6 groups of shades (which are the
buttons 1 to 6).
The instructions below assign a shade to group 1. Depending
on your preference you can choose your own group.
This instruction will make use of the OPEN, GROUP 1, and
STOP buttons on your Remote.
Find the shade button on your shade.
Different shade types have different shade buttons. Consult
the shade documentation for the exact location of the shade
button.
Open
Group 1
Stop
ADDING A SHADE TO A REMOTE
7
Shade button
4.1 PRESS STOP FOR 6 SECONDS
(Keep pressing until the Remote lights start blinking).
4.2 PRESS GROUP 1
(This will activate the group 1 on the Remote).
4.3 PRESS AND HOLD THE SHADE BUTTON
4.4 PRESS THE OPEN BUTTON
(You will see the shade move up and down shortly).
4.5 RELEASE THE SHADE BUTTON
4.6 IF YOUR REMOTE IS STILL FLASHING: PRESS STOP
FOR 6 SECONDS AND HOLD
(Keep pressing until the flashing stops).
ADDING A SHADE TO A REMOTE
8
STEP 5 CONNECT AND SET UP HUB
CONNECT POWER TO HUB:
5.1 CONNECT ONE END OF THE USB
POWER CABLE TO THE USB POWER
SUPPLY
5.2 PLUG THE USB POWER SUPPLY INTO
AN AC OUTLET OR POWER STRIP
5.3 PLUG THE OTHER END OF THE USB
POWER CABLE INTO THE POWER
PORT ON THE BACK OF THE HUB
Note: During the boot-up process, the Hub’s LED may turn
off and on again. Once the Hub has completed the boot-up
process, the Hub’s LED will turn solid Magenta. Do not interrupt
the boot-up process by cutting power or pressing any buttons
on the back panel of the Hub.
CONNECT AND SET UP HUB
99
Central Hub placement should be considered to
obtain optimal range of the Hub.
CONNECT AND SET UP HUB
10
CONNECT HUB TO INTERNET CONNECTED WIRELESS ROUTER:
Connect using an active Wi-Fi network:
5.4 OPEN THE POWERVIEW® APP ON YOUR
MOBILE DEVICE AND FOLLOW THE ONSCREEN
INSTRUCTIONS TO PROPERLY CONNECT TO AN
ACTIVE WIFI NETWORK
(The Hub will indicating it is ready to join the PowerView® Network, once the
Hub has been connected to the home network).
CONNECT USING AN ETHERNET CABLE:
(Optional)
5.5 CONNECT THE ETHERNET CABLE FROM THE
HUB TO AN OPEN LAN PORT ON YOUR ROUTER
(If connecting the Hub to the home network via Ethernet, connect the Hub
to the router, before connecting the Hub to power).
Other manuals for PowerView Motorisation
1
Other LuxaFlex Remote Control manuals
