LOWE'S EUREKA Series User manual
ITEM #1596997
1596998
EUREKA LED
CEILING FAN
Español p. 17
MODEL #EUK60BNK10LRS
EUK60BZ10LRS
ATTACH YOUR RECEIPT HERE
Purchase Date
1
Questions, problems, missing parts? Before returning to your retailer, call our customer service
department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST, Monday - Friday.
2
Safety Information ...............................................................................................................
.
. 2
Package Contents ..............................................................................................................
.
. 4
Hardware Contents
...........................................................................................................................
5
Preparation ........................................................................................................................... 5
Initial Installation ................................................................................................................... 5
Wiring .................................................................................................................................. 11
Final Installation .................................................................................................................. 10
Operating Instructions ......................................................................................................... 13
Care and Maintenance ...................................................................................................
.
.... 14
Troubleshooting .................................................................................................................. 15
Limited Lifetime Warranty ................................................................................................... 16
Replacement Parts List ....................................................................................................... 16
TABLE OF CONTENTS
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage that
might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code
and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you
are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the
floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan is: 29 lbs.
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. (15.9 KG) OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a
qualified electrician if in doubt.
WARNING
The DC Motor will not operate until blades are installed.
SAFETY INFORMATION
3
Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.
Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly to
ensure that they are secured.
Do NOT tamper with or attempt to repair LED component. The light source is designed for this
specific application and should not be serviced by untrained personnel. If any servicing is
required, call our customer service department.
Due to the weight and construction of this fixture, it is advisable to seek the help of another
person.
CAUTION
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a
plastic outlet box. Secure the outlet box directly to the building structure. The outlet box and its
support must be able to support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan
are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blades when
installing them, balancing the blades or cleaning the fan. Do not insert objects between the
rotating fan blades.
To reduce the risk of personal injury, use ONLY parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
Before installation, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
When using an existing outlet box, make sure the outlet box is securely attached to the building
structure and can support the full weight of the fan. Failure to do this can result in serious injury or
death. The stability of the outlet box is essential in minimizing wobble and noise in the fan after
installation is complete.
To reduce the risk of serious bodily injury, DO NOT use power tools to assemble any part of the
fan, including the blades.
WARNING
PACKAGE CONTENTS
4
4
A Mounting Bracket 1
B Canopy Mounting Screw 2
(preassembled)
C Downrod 1
D Pin (preassembled) 1
E Clip (preassembled)
F Canopy 1
G Canopy Cover 1
DESCRIPTIONPART QUANTITY DESCRIPTIONPART QUANTITY
H Yoke Cover 1
I Motor Assembly 1
J Blade 10
K Blade Bracket 5
L Blade Bar 10
M Shade 1
N
Remote Pack
1
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
A
L
M
G
C
D
B
E
H
I
K
J
N
F
5
HARDWARE CONTENTS (shown actual size)
Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on
foam to avoid damage to finish. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder, Wire Strippers and Precision Screwdriver (0 x 2 in.).
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and
Wire Cutters.
PREPARATION
CC
Blade
Screw/Washer
Qty. 40
+ 1 extra
Wire
Connector
Qty. 3
AA BB CC
INITIAL INSTALLATION
ON
OFF
ON
OFF
1
Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
Decorative
Nut
Qty. 20
+ 1 extra
INITIAL INSTALLATION
6
Check to make sure blades (J) will be at least
30 inches from any obstruction at least 7 ft. above
the floor.
3.
2. Determine mounting method to use.
A. Standard mount
B. Angle mount
IMPORTANT: If using the angle mount, ensure the
ceiling angle is not steeper than 19°.
NOTE: Closemount option is not available for this
fan.
*Helpful Hint: Downrod-style mounting is best
suited for ceilings 8 ft. high or higher. For taller
ceilings you may want to use a longer downrod
(not included). Angle-style mounting is best suited
for angled or vaulted ceilings. A longer downrod is
sometimes necessary to ensure proper blade
clearance.
2
B
A
7 ft.
min.
30 in.
min.
3
J
19° max.
4.
Open End
4
A
A
ANGLE MOUNTSTANDARD MOUNT
Secure mounting bracket (A) to outlet box (not
included) using screws, spring washers and flat
washers provided with the outlet box.
*NOTE: It is very important you use the proper
hardware when installing the mounting bracket (A)
as this will support the fan.
IMPORTANT: If using the angle mount, make sure
open end of mounting bracket (A) is installed facing
the higher point of the ceiling, and ensure the
ceiling angle is not steeper than 19°.
INITIAL INSTALLATION
7
Remove pin (D) and clip (E) from downrod (C).
Partially loosen preassembled set screws and nuts
in yoke at top of motor assembly (I).
5a. 5A
E
5B
C
Set Screw
Sideview
D
Yoke
6. Insert downrod (C) through canopy (F), canopy
cover (G) and yoke cover (H). NOTE: Canopy
cover (G) must be turned with the shiny side
toward the motor assembly (I).
Then, thread wires from motor assembly (I)
through downrod (C).
6
F
H
7. Slip downrod (C) into motor assembly yoke, align
holes and re-install pin (L) and clip (M). Tighten
set screws in motor assembly yoke and then
tighten preassembled nuts on the set screws.
Then, slide yoke cover (E) down until it rests on
top of motor assembly (I).
7C
I
H
D
E
Yoke
E
D
Set Screw
and Nut
Sideview
C
5b.
I
G
8
INITIAL INSTALLATION
BB
AA
DANGER: To reduce the risk of serious bodily
injury, DO NOT use power tools to assemble the
blades (J). If overtightened, blades (J) may crack
and break.
Select five blades (J) to attach the five blade
brackets (K). Place one blade bracket (K) on top
of blade (J) aligning the two biggest of four holes
at top of blade (J). Attach blade bracket (K) to top
of blade (J) with two blade screws/washers (AA),
and two decorative nuts (BB).
Repeat step for the other four blades (J).
8. 8
Hardware Used
Blade Screw/Washer x 10
AA
Hardware Used
Decorative Nut x 10
BB
J
K
I
8a
Align the two smallest of four holes of blade
bracket (K) with the two holes on one of the
rectangular-shaped blade arms on the edge of
motor assembly (I).
Attach blade (J) to blade arm with two blade
screws/washers (AA) only.
Repeat step for the other four blades (J).
8a.
Hardware Used
Blade Screw/Washer x 10
AA
Rectangular-shaped
blade arm
AA
K
J
9
J
I
8b
Attach one of the remaining five blades (J) to the
V-shaped blade arms on the motor assembly (I)
using two blade screws/washers (AA) and two
decorative nuts (BB).
Repeat step for the other four remaining blades (J).
8b.
Hardware Used
Blade Screw/Washer x 10
AA
Hardware Used
Decorative Nut x 10
BB BB
V-shaped
blade arm
AA
L
JAA
AA
Connect each blade (J) using the blade bars (M).
On the topside of the blade (J), slide the bent
portion of the blade bar (L) directly under the
opening at the end of the blade bracket (K),
aligning the holes. Then, on the underside of the
blade (J), insert the nodule portion of another blade
bar (L) directly under the same hole. Secure with
one blade screw/washer (AA).
NOTE: Blade bar (L) must be turned with the
smooth side toward the floor.
Repeat step for the remaining blade bars (L) until
the blades (J) are all connected.
CAUTION: Assistance from another person is
recommended for this step.
8c.
Hardware Used
Blade Screw/Washer x 10
AA
8c
LJ
nodule
smooth
side
AA
INITIAL INSTALLATION
K
KL
10
INITIAL INSTALLATION
Depending on the length of downrod you use, you
may need to cut the lead wires back to simplify
the wiring. If you decide to cut back the lead
wires, it is suggested you do so in the following
manner:
Take the lead wires and make sure you have
pulled them all the way through the top of the
downrod. Start at the TOP of the hanging ball on
the downrod and measure 8 in. of lead wire, then
cut the excess wire off with wire cutters (not
included).
NOTE: If you do not cut back the lead wires,
Steps 9 and 10 are not necessary and you may
proceed to Step 10 instead.
9.
Hanging
Ball
9
C
8 in.
If you decided to cut back the lead wires in Step 9,
strip 1/2 in. of insulation from end of each
wire -- WHITE, BLACK, GREEN AND BLUE (if
applicable). Twist stripped ends of each strand of
wire within the insulation with pliers (not included).
10. 10
Install hanging ball of downrod (C) into opening of
mounting bracket (A). Align one of the slots in
hanging ball with tab in mounting bracket (A).
DANGER: Failure to align one of the slots in
the ball with the tab may result in serious injury or
death.
11.
C
Tab
11
A
Slot
This manual suits for next models
2
Table of contents
Other LOWE'S Fan manuals
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
