Logosol E4 User manual
USER MANUAL
LOGOSOL Speed Saw
Read through the user manual carefully and make sure you understand its contents
before you use the planer/moulder.
This user manual contains important safety instructions.
WARNING! Incorrect use can result in serious personal injury or even death to the
operator or others.
USER MANUAL IN ORIGINAL FORMAT.
2
Welcome! We are very pleased that you have
demonstrated your condence in us by purchasing
this planer/moulder. We will do our utmost to meet
your expectations.
LOGOSOL has been manufacturing wood processing
machines since 1988, and since then we have supplied
approx. 30 000 machines to satisfied customers
worldwide.
We care about your safety as well as we want you
to achieve the very best possible reslults from your
machine. We therefore recommend that you take
the time to read this user manual from cover to cover
before you begin sawing. Remeber that the machine
itself is just part of the value of the product. Much of
the value is also to be found in the expertise we pass
on to you in the user manual. It would be a pitty if that
were not utilized.
We hope you get a lot of satisfaction from the use of
your new machine.
Bengt-Olov Byström
Founder and Chairman of the Board
LOGOSOL AB, Härnösand, Sweden
Thank you for choosing
a LOGOSOL machine!
LOGOSOL is engaged in continuous development of its products.
We must therefore reserve the right to change
the design and form of our products.
Text: Mattias Byström
Translation: Anna Byström Olsgren
Document: Logosol Speed Saw Manual
Illustrations: Erik Svensson
Last revised: April 2013
Manual, ref. no: 0458-395-0440
© 2013 LOGOSOL, Härnösand Sweden
3
LOGOSOL Speed Saw
Table of contents
Safety instructions 4
Overview 5
Machine description 9
Tools required 9
Assembly 10
Lifting instructions & setup 17
Fitting guide bar & chain 17
Chain lubrication & water cooling 18
Adjustable slide blocks 18
Sawing with the Logosol Speed Saw 19
Cutting equipment 19
Storing the electric saw 19
Elecrical system 20
Technical data 20
EC Declaration 23
4
KEY TO SYMBOLS
For your own safety, read through the entire
user manual carefully and do not start the ma-
chine before you have understood everything.
Use approved ear protectors and protective
eyewear. Hearing can be damaged even after
short periods of exposure.
Rotating saw chain. Make sure that your n-
gers never move into the vicinity of the guide
bar. Never reach over the guide rail. Never
touch the Speed Saw when it is running.
This symbol means ’WARNINg’. Pay particular
attention where this symbol appears in the
manual text.
A warning comes after this symbol. Pay par-
ticular attention where this symbol appears in
the manual text.
• Read the entire user manual carefully before
using the electric saw. Risk of mortal danger if
you do not follow the safety instructions.
• LOGOSOL E8 Speed Saw is exclusively intended
for rip sawing with the LOGOSOL Sawmill.
Improper use can cause serious injury. Always be
concentrated and careful when using this saw
unit.
• Fit support legs under the guide rail before
pushing the saw unit onto the sawmill.
Otherwise the LOGOSOL Sawmill will tip over,
unless there is no load on the log beds.
• Always make sure that the saw unit is pushed
fully into position on the guide rail before
connecting the power cable. If not all four
plastic proles clutches the guide rail anges,
there is risk of the saw unit being thrown out
when started.
• Make sure that the power cable can run freely
over the entire sawmill length. Never step on the
cable. The power cable should be suspended by
a wire above the sawmill.
• The eleectric saw together with the LOGOSOL
Sawmill is a one-man sawmill. Respect the
safety distance due to high noise level and risk
of a broken chain being hurled out from the
guide bar.
• Turn the saw unit off after each saw cut.
• Never work alone and make sure there are other
persons within earshot whom you can summon
if you need help.
• Always wear protective clothing and use
personal protective equipment: Close-tting
work overalls are appropriate. Never operate the
unit wearing loose-tting clothes, overall coats
or similar.
• Use safety shoes with high-grip soles and steel
toecaps. Neckerchiefs, ties, jewellery or other
items that can get caught in the equipment are
not to be worn.
• Never stretch over or under the Logosol
sawmill’s guide rail when the sawmill is in
operation. Rotating saw chain. Risk of cut
injuries! The saw chain and other rotating parts
are accessible on the guide bar side, underneath
the saw unit on the operator side, and in the
sawdust duct.
• Wear strong protective gloves. Risk of cut
injuries when handling the guide bar and the
saw chain. Cutting equipment can also be hot
immediately after sawing.
• Never leave the saw unattended with the power
cable connected so that unauthorized persons
can start it.
• After service, the machine should be returned
to its original condition. Only use original spare
parts.
• Always disconnect the power before:
...changing guide bar and chain.
...adjusting, cleaning or other servicing.
...touching the moving parts of the saw unit.
...lifting the saw unit off the LOGOSOL Sawmill.
safety instructions
Hearing can be damaged after relatively
short periods of exposure to the high
frequency noise of the motor and the
cutting equipment.
5
LOGOSOL Speed Saw
overview
- 6608-000-0005 E8 Speed Saw 400V
- 6608-000-0010 E8 Speed Saw 230V
- 6608-000-0015 E4 Speed Saw 400V
- 6608-000-0020 E4 Speed Saw 230V
1. 8000-001-000X Motor, 4kW
6608-001-000X Motor, 8kW
2. 6608-001-0060 Chassis
3. 3008-010-0050 Guide bar 50 cm
3008-010-0070 Guide bar 70 cm
4. 6608-001-0130 Sawdust guard
5. 6608-001-0120 Right handle
6. 6608-001-0125 Left handle
7. 6608-001-0215 Tube, bar nose steering
8. 6608-001-0205 Bracket, bar nose steering
9. 6608-001-0210 Magnet holder
10. 6608-001-0225 Magnet, bar nose steering
11. 6608-001-0135 Feeder holder
12. 6608-001-0250 Line holder
13. 6605-000-0100 Water cooling
14. 5220-001-0059 Locking handle, excentric
15. 6608-001-0110 Right cover plate
16. 6608-001-0115 Left cover plate
17. 6608-001-0140 Knurled knob
18. 6608-001-0005 Cover plate
19. 6608-001-XXXX Cable hook
20. 6608-001-0010 Motor mount
21. 6608-001-0015 Chain tensioner
22. 6608-001-0040 Spacer 12 mm
23. 6608-001-0025 Spacer 5 mm
24. 6608-001-0030 Outer chain guide
25. 6608-001-0035 Chain pulley 24t
26. 6608-001-0020 Spacer 10 mm
27. 6608-001-0045 Washer, motor shaft
28. 6608-001-0100 Aluminium prole
29. 6608-001-0105 Slide strip 50 mm
30.
9999-000-6031 Adjusting aluminium prole
31. 6670-001-0006 Locking plate, slide strip
32. 6608-001-0075 Bar mount
33. 6608-001-0080 Bar plate
34. 6608-001-0085 Cover plate
6
1
2
4
3
7
14
6
5
17
19
15
11
12
8
9
17
Operator side
13
Guide bar side
Backward
Forward
7
LOGOSOL Speed Saw
20
14
18
1
2
22
21
23
24
25
24
26
22
23
27
8
28
29
30
31
34
2
32
33
9
LOGOSOL Speed Saw
machine description
LOGOSOL Speed Saw is a chainsaw unit that is
intended for usage on the LOGOSOL Sawmill.
The slide elements, which t on the sawmill guide rail,
are integrated in the machine. The saw is driven by an
electric motor, which transmits the power to the chain
via a large chain pulley.
The guide bars that are to be used, are specially adapted
for the Speed Saw and are available in different lengths
supplied by LOGOSOL. The Speed Saw has no own
electrical system, but has to be connected to a manual
feeder unit (ref. no. 6000-000-6005) or the automatic
feeder unit E37 (ref. no. 6600-000-3015).
In its basic design the saw has a solenoid valve that
controls the oil ow to the bar. Besides this, the Speed
Saw has no own electrical system.
THE LABELING ON THE MACHINE
tools required
• Allen key 4 mm (3/16’’)
• Allen key 5 mm (1/4’’)
• Combination wrench 10 mm (7/16’’)
• Combination wrench 13 mm (9/16’’)
• Combination wrench 17 mm (11/16’’)
• Screwdriver (or something else that is suitable for
locking the rotation of the chain pulley)
10
2. Place the chassis (2) on the motor mount (20) and
t the chain tensioner (21) to the chassis according
to the gure to the left. Then fasten the full thread
M6x60 bolt in the chain tensioner using an M6 nut.
Screw the three components together using four
excentric locking handles (14).
1. Fit the motor mount (20)* with four M8x20
countersunk Allen screws. Use medium strength
threadlocker and torque the screws to 25 Nm.
Then t the cover plate (18) with two countersunk
Allen screws.
* Position no. in the exploded views.
assembly
This manual suits for next models
1
Table of contents
Other Logosol Saw manuals
Logosol
Logosol BS350 User manual
Logosol
Logosol B751PRO User manual
Logosol
Logosol PH260 User manual
Logosol
Logosol F2+ User manual
Logosol
Logosol SMART SET User manual
Logosol
Logosol BS350 User manual
Logosol
Logosol B751 User manual
Logosol
Logosol E4000 User manual
Logosol
Logosol M7 User manual
Logosol
Logosol PH360 User manual
