Logitech X56 HOTAS User manual
LogitechG.com
USER MANUAL / MANUEL DE L’UTILISATEUR
X56 HOTAS
SYSTÈME 3M
(MAINS SUR MANCHE ET MANETTE)
HANDS ON THROTTLE AND STICK
English . . . . . . . . . . . . . . . 3
Français . . . . . . . . . . . . . 23
Español . . . . . . . . . . . . . . 43
Português . . . . . . . . . . . . 63
English 3
STICK OVERVIEW
A. POV
B. Mini Analog Stick
C. Thumb HATs, Witches and
Castle
D. Stick Buttons with Trigger
and 2 x Head Buttons
E. X, Y, and Rz Axes, Elevator,
Aileron and Rudder Axes
F. Pinkie and Flying Pinkie
G. F.E.E.L. Spring System
4 English
THROTTLE OVERVIEW
A. Throttle Rotaries with inset buttons
B. 2-position Slider
C. Thumb Controls with 2 HATs, Thumb Button,
Mini AnalogStick
D. Twin Throttles with Throttle Lock
E. Throttle Tension Adjuster
F. 3-position Mode Switch
G. Base Controls with 7 Toggles and 2 Rotaries
English 5
GETTING STARTED
Drivers and Software Installation
Windows®7/8/10
1. Download and install the X56 HOTAS software from logitech.com/support/x56
2. After reading the Disclaimer, select the 'I accept the terms of the Disclaimer' option
andclick 'NEXT' to continue
3. At the Plug In screen, plug the Stick and Throttle units into the PC. Click ‘Next’ when
itbecomes highlighted
4. From the end screen, click ‘Finish.’ Your drivers and software are now installed
NET Framework
1. If this is the rst Logitech product that you have installed, you may be asked to install
.NET Framework after the software installation nishes. This is strongly recommended;
this Microsoft Feature Update is required by the Software
2. Click ‘Download and install this le.’ The PC will now nd the correct les from
theInternet and download them
3. When the installation nishes, click ‘Close’
6 English
CONTROLLER SETTINGS
If at any time you wish to check that the X56 is working correctly, open the Game Controllers
page and click on the controller’s Properties tab.
Here are the various ways to do this from each operating system:
Windows®8/10
1. From the Metro/Start screen, click the ‘Control Panel’ icon. NOTE: If you have
noControlPanel icon on your Metro/Start screen, type ‘control panel’ and the icon
fortheControl Panel will appear
2. Once the Control Panel is open, double-click on the ‘Devices and Printers’ icon.
NOTE:Ifyou cannot see this icon, make sure that you have large icons selected
3. With the Devices and Printers screen open, nd the X56 HOTAS in the device list and right-
click on this icon. From the dropdown menu, select ‘Game Controller Settings’
4. From the Game Controllers window, you should see the X56 HOTAS. listed and selected.
Click ‘Properties’ and this should take you to the Controller Test screen
From the Controller Test screen you can test all the functions, axes, buttons, rotaries, etc.
Whenyou have completed your tests, click ‘OK’ twice to get back to the main desktop
English 7
Windows®7
1. Click on the ‘Windows’ icon from the system tray. Hover over the All Programs menu.
Clickthe ‘Games’ folder and then the ‘Games Explorer’ icon
2. Click the ‘Tools’ option (with downward facing arrow) from the list across the top
ofthewindow. From the dropdown list, click ‘Input Devices’
3. From the Game Controllers window, you should see the X-56 Rhino listed and selected.
Click‘Properties’ and this should take you to the Controller Test screen
RED GREEN YELLOW BLUE Notes
k = Rate 1 2 3 4
OD = Outside diameter 33 33 33 33
d = Wire diameter 1.8 1.8 1.8 1.8
E = Youngs Modulus ( 210000 ) 210000 210000 210000 210000 N/mm2
FL = Free length 52 47 42 36 Un-compressed
WL = Working length 30.8 30.8 30.8 30.8 Pre-compressed
P1L = Position 1 length 25.8 25.8 25.8 25.8 Full Working Compression
n = Total Number of coils 4.5 4.5 4.5 4.5 Active coils (6.5 coils in spring)
D = Mean Diameter 31.2 31.2 31.2 31.2
Rate K= Ed*4/ 8n D *3 1.70 1.70 1.70 1.70 N/mm
Load @ Breakout BL = FL-WL x k 36.12 27.60 19.08 8.86 N
Load @ P1L SoL = FL - SL x k 44.64 36.12 27.60 17.38 N
Stress= 8 x P x D/3.14 x d *3 608.50 492.38 376.25 236.90 N/mm2
% UTS ( M4 Music Wire ) 30.89 24.99 19.10 12.03 %
8 English
F.E.E.L. Spring Tension System
Each spring placed on the Rhino stick shaft will give a dierent feeling. You can also operate
thestick without a spring, providing a total of ve dierent forces.
Each spring has a unique feel and dierent identication. These identiers are color swatches
at the top of each spring – Red, Yellow, Blue, and Green. This table lists some of the calculations
used for dierentiation:
9 English
Changing or removing a spring
To insert, change, or remove a spring, follow these steps. Ensure the trigger is facing away from
you and that the X56 HOTAS logo plate is facing you.
1. Turn the Locking Bezel (part B) counterclockwise until the Stick comes away from the base.
2. Remove the Seal Ring (part C) by placing the ngers from your left and right hand under
thering on either side, and then lift up. The Seal Ring is sti by design.
3. Pry apart the Locking Clamps (part D). These pull apart from the stick, but are under load
from the spring. Take one half o rst, hold the spring, and then remove the other half.
4. Remove the Spring (part E), then either replace with a new Spring of leave the Spring o.
To reassemble, reverse the order of the above steps, making sure to securely seat the Seal Ring
(Part C) and rmly tighten the Locking Bezel (part D) on the Stick base.
Note: When changing springs, please ensure that the USB cable is disconnected from your PC
and avoid touching the connectors in the stick handle and base.
1. Turn Locking Bezel
counterclockwise
4. Pry apart Locking Clamps
2. Remove Stick
5. Remove Spring
3. Remove Seal Ring
English 10
Software Overview
The software allows you to program the X56 with an array of keyboard commands, from basic
single-key commands to very advanced, timed, and macro commands. It will also allow you
toprogram any axis with keyboard commands, and program mouse commands.
In the software you can also alter the response curves and deadbands of the main axis –
we’llcover the explanation of these topics later in the manual.
There are two ways to launch the software:
1. From the desktop icon that looks like this 2. From the start menu bar...
Once the software launches, you will be presented with the Home Screen.
If it’s the rst time you’ve run the software, you will be asked to choose your language.
Oncethisis done the main Home Screen will appear. If you’ve made a mistake choosing
yourlanguage or you wish to choose another language, the language menu can be accessed
byclicking on the icon in the bottom-right corner of the Home Screen.
There are three main Tabs within the software:
1. HOME
2. PROGRAMMING
3. SETTINGS
Other manuals for X56 HOTAS
2
Table of contents
Languages:
Other Logitech Video Game Controllers manuals
Logitech
Logitech 963290-0403 - Extreme 3D Pro Joystick Operating manual
Logitech
Logitech 920-000946 - G13 Advanced Gameboard Command... User manual
Logitech
Logitech Gamepad F310 User manual
Logitech
Logitech 963311-0403 - Action Controller Game Pad User manual
Logitech
Logitech Bluetooth wireless hub User manual
Logitech
Logitech WingMan User manual
Logitech
Logitech PRO RACING PEDALS User manual
Logitech
Logitech FLIGHT RUDDER PEDALS User manual
Logitech
Logitech Gamepad F310 User manual
Logitech
Logitech 963325-0403 - RumblePad 2 Vibration Feedback Gamepad Game... User manual
Logitech
Logitech Gamepad F310 User manual
Logitech
Logitech G27 RACING WHEEL User manual
Logitech
Logitech G923 User manual
Logitech
Logitech 939-000183 - Wireless Drum Controller User manual
Logitech
Logitech F710 User manual
Logitech
Logitech WingMan Force 3D User manual
Logitech
Logitech 941-000040 - Speed Force Wireless Wheel User manual
Logitech
Logitech Freedom 2.4 User manual
Logitech
Logitech DRIVING FORCE User manual
Logitech
Logitech PRO RACING WHEEL User manual
