Logan Graphic Products 5000 User manual

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com

L1878N rev.2 5/14

Model 5000

8-Ply Mat Cutter

Instruction Manual

Identification

Blade Installation

NOTE: Use only special 8-Ply blade #271. It has only one sharp, bev-

eled edge. DO NOT USE #270 which looks similar but has two beveled

edges. The #270 blade will not cut 8-Ply effectively (Fig. 1).

NOTE: Only one corner of blade #271 can be used (Fig. 2).

1. Loosen blade knob and remove cartridge.

2. Set blade onto blade slide, being careful of orientation of edge bevel (Fig. 3).

3. Insert blade slide into cutting head (Fig. 4).

4. Tighten blade knob.

Depth Adjustment

NOTE: Standard 8-Ply depth setting is aligning end of blade with end

of slide (Fig. 5).

1. Set cutter onto 8-Ply mat board with blade overhanging edge.

2. Depress blade fully.

3. Corner of blade tip edge should score the slip sheet past top of bevel edge (Fig. 6).

4. To adjust depth, loosen blade knob and turn depth adjustment screw.

NOTE: When reducing depth, you will have to push blade back with

your finger.

5. Retighten blade knob.

Nylon Guides

Blade Knob

Blade

Slide

Depth Knob

Fig. 4

Start & Stop Lines

Anti-crawl pin

8-Ply Bevel Cutting Instructions

Fig. 1

Fig. 2

ONLY USE THIS CORNER

#271 SINGLE BEVEL 8-PLY BLADE

Single Bevel

Fig. 5 Fig. 6

SLIP SHEET

8-PLY MAT

CAUTION!!

MAT CUTTING BLADES ARE SHARP

Fig. 3

Front Back

#271 BLADE

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com

L1878N rev.2 5/14

Model 5000

8-Ply Mat Cutter

Instruction Manual

Helpful Hints

• Usetwohandstocut.

• Settingbladedepthtoodeepcanresultinbladetipchippingoff.

• Changebladeoften.

• Useonebladecornerwhencutting8-Ply.

• Ifyoudonotcutthroughthemat,repeatcut.

• Ifyourovercutsaretoolongortooshort,start&stopinsideoroutsidestart/

stop lines to adjust.

Adjust Nylon Guides (use Phillips Screwdriver)

To improve straightness of cut, you may need to adjust the guides fit on guiderail.

1. Hook cutter onto rail.

2. Loosen guide screws (Fig 12).

3. Squeeze guide against rail.

4. Retighten guide screws.

Fig. 12

INCH

Fig. 9

Fig. 10 Fig. 11

Fig. 8

Cutting an 8-Ply Mat

1. On back of mat, draw pencil lines for location of opening (Fig. 7).

2. Place your mat (color side down) on a slip sheet (scrap matboard) which must be larger than the mat.

3. Align straight edge on left side of line or slide under guiderail and up against the mat guide and squaring arm.

4. Hook cutter onto rail edge and align GREEN scribe line with top pencil line

(Fig. 8)

5. With left hand, depress the anti-crawl pin and firmly pivot the blade holder down into the mat (Fig. 9).

6. Pull cutter along rail until the red scribe line meets the bottom pencil line

(Fig. 10)

7. Pivot blade out of mat. Repeat remaining three sides

(Fig. 11)

Fig. 7

Table of contents

Other Logan Graphic Products Cutter manuals

Logan Graphic Products

Logan Graphic Products 709-1 User manual

Logan Graphic Products

Logan Graphic Products FoamWerks WA-8001 User manual

Logan Graphic Products

Logan Graphic Products Platinum Edge 850 Manual

Logan Graphic Products

Logan Graphic Products 301-S Manual

Logan Graphic Products

Logan Graphic Products 655 Framer's Edge User manual

Logan Graphic Products

Logan Graphic Products 650-1 User manual

Logan Graphic Products

Logan Graphic Products SIMPLEX V-Groover 703 Manual

Logan Graphic Products

Logan Graphic Products 525 Manual

Logan Graphic Products

Logan Graphic Products 550-1 Manual

Logan Graphic Products

Logan Graphic Products ARTIST CLASSIC Manual

Logan Graphic Products

Logan Graphic Products 301-S User manual

Logan Graphic Products

Logan Graphic Products 707 Manual

Logan Graphic Products

Logan Graphic Products 545 User manual

Logan Graphic Products

Logan Graphic Products 424 User manual

Popular Cutter manuals by other brands

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Original instructions

Makita

Makita DCS552 instruction manual

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 user manual

Makita

Makita 4112HS instruction manual

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S manual

Hitachi

Hitachi CM 4SB2 Safety instructions and instruction manual

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 instruction manual

GCC Technologies

GCC Technologies AFJ-24S user manual

DeWalt

DeWalt XR LI-ION DCS350N manual

Baudat

Baudat ES1 instruction manual

Mafell

Mafell ZAF 200 Operating instructions and spare parts list

Makita

Makita 4100NH instruction manual

Formax

Formax FD 574 Operator's manual

EINHELL

EINHELL TE-MA 1500 Original operating instructions

Husqvarna

Husqvarna Cut-n-Break K 760 Operator's manual

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Operator's manual

TRI tool

TRI tool 301A user manual

Roller

Roller King 1 1/4 operating instructions