Locosys GW-60 User manual
1
www.locosystech.com
Quick Start Guide
GW-60
RESET/▼
GPS Function
MODE/BACK
Blinking:
searching for GPS
Steady on:
GPS is ready
Alarm status
Battery level
Charging
status
ADJUST/
↵
START/▲
GPS Antenna
Full charge
2
www.locosystech.com
Section 1. Brief Introduction
1.1 Before operating your GW-60, clip the device and
full-charge it with DC +5V/500mA charger for at least
3~4 hours.
1.2 Press MODE/BACK to select Time modes
(1) CLOCK; (2) ALARM; (3) STOPWATCH; (4) TIMER
1.3 Press ADJUST/
↵
to setting page.
3
www.locosystech.com
1.4 Press GPS to GPS mode. GPS signal will be searched
automatically.
1.5 Backlight: Hold MODE/BACK for 2 sec.
(Press any key to extend backlight time)
1.6 Lock screen: START+MODE, press again to unlock.
1.7 Sleep mode: Hold GPS for 1 sec to sleep mode.
At clock mode, GW-60 will turn to sleep mode in 15sec.
Tip: Press MODE/BACK to wake up the watch.
4
www.locosystech.com
Section 2. Time Mode
2.1 Clock Mode
Display local time based on the GMT setting.
Tip: Quick clock time setup for first time usage.
(1) GMT Setting: Refer to 3.6
(2) GPS Time Synchronization: Under open sky
environment, switch to GPS mode and wait until the
GPS fixed. GW-60 will automatically synchronize to
precise GPS UTC time.
2.2 Alarm Mode
Press ADJUST/
↵
to adjust alarm time.
Press ▲ / ▼ button to select numbers and
ADJUST / BACK to start/end adjustment.
2.3 Stopwatch Mode
Press START to start counting time and press again
to pause.
Press RESET to reset counting time to “00:00
00
”.
Press MODE/BACK to exit.
2.4 Timer Mode
Press ADJUST to start adjusting timer.
Press ▲ / ▼ to change numbers and MODE/BACK
button to end adjustment.
Press START to start counting down and press again
to pause.
Press RESET to restart timer
5
www.locosystech.com
Section 3. Setting
3.1 Setting page:
ADJUST/
↵
: Enter edit mode/ Confirm.
▲: Up.
▼: Down.
MODE/BACK: Exit edit mode/ Cancel.
3.2 BUZZER: set buzzer/ sound.
O : On/ Enable.
X : Off/ Disable.
3.3 LOGGING: Log rate setting.
OFF : No logging.
1HZ : When speed over [MIN SPEED], log rate in 1Hz.
5HZ : When speed over [MIN SPEED], log rate in 5Hz.
SMART:
[MIN SPEED] ≦ Speed < [SPD GENIE] : 1Hz log rate.
[SPD GENIE] ≦ Speed : 5Hz log rate.
3.4 MIN SPEED: Speed threshold, only logged speed above
[MIN SPEED].
Available number: 0 to 15 [UNIT].
6
www.locosystech.com
3.5 UNIT: Speed measurement unit.
KM : Kilometer.
MI : Mile.
NM : Nautical mile.
3.6 GMT: Set GMT/Time zone, e.g. +8:00 for Taipei.
Available number: GMT-12:00 to GMT+13:00.
3.7 SPEED AVG: Time interval for speed averaging.
Available number: 1 sec to 60 sec.
3.8 SPD GENIE: Auto-speed report, setting the minimum
speed threshold to initiate [SPD GENIE].
Available number: 0 to 63 [UNIT].
3.9 ACTION SPEED: Speed display type
SPEED : Current speed (200ms average)
NS AVG : N-second average speed based on [SPEED
AVG].
7
www.locosystech.com
3.10 SPD FONT: Speed display font for Speed report.
SMALL : Small font.
BIG : Big font.
3.11 SPEED HISTORY: Display speed history record in
speed report.
O : On/ Enable.
X : Off/ Disable.
3.12 SCROLL SECOND: Set scroll second in speed report
Available number: 1 sec to 2.5 sec.
3.13 USB CLASS: Connection type
COM: Virtual COM PORT for Windows platform user.
UMS: USB Mass Storage for non-Windows platform user.
(Note: Set UMS before entering “MSC mode”on 3.14)
8
www.locosystech.com
3.14 TO USB MSC: Connection by Mass Storage Class (MSC)
mode mainly for non-Windows platform user.
Tip: How to get GPS data in USB MSC mode
(1) Set“USB CLASS”option to“UMS”first.
(Note: Before setting, the USB charging cable MUST be
disconnected.)
(2) Connect to USB, and press ADJUST/
↵
“TO USB
MSC”to enter USB MSC state.
(3) Find a new flash drive with a READ only file—
GPSLOG.SBP on your host PC.
(4) Remove USB cable to exit.
3.15 FIRMWARE VERSION: check device status
Firmware Version: VX.XXXXXX
User Name: XXXXXX
Serial Number: SXXXXXXXX
GPS Version: XXXX
9
www.locosystech.com
Section 4. GPS Mode
4.1 Action Speed: Display current instant speed or N-sec.
average speed.
Vertical Bar: Log memory usage.
Horizontal Bar: Speed accuracy indicator.
(Long bar means good signal)
Symbol :Not logging data
Symbol : logging data
Press ▲ / ▼ to move on next page “Top 10
Speeds”, “Top 10 AVG Speeds” and “PVT”.
GPS searching
GPS fixed
10
www.locosystech.com
4.2 Auto Speed Report: If [SPD GENIE] is enabled, the
auto speed report screen shows at the end of each
session.
e.g. MAX SPEED: 61.65 KH
N-SEC SPEED: 50.57 KH
(Medal icon: New record achieved.)
When in Big Font mode, 3 screens are displayed one
after another
MAX SPEED
N-SEC SPEED
SPEED HISTORY (If SPEED HISTORY turns on)
4.3 Distance Traveled: Display distance traveled when
data logging.
Press ▲ / ▼ to next page/ previous page.
Small Font
Big Font
Other manuals for GW-60
1
Table of contents
Other Locosys Watch manuals
