Linksys WAP4400N Operation manual
PRODUCT DATA
BUSINESS SERIES
Wireless-N
Access Point with Power
Over Ethernet
Model: WAP4400N
High-Speed Wireless Access for Existing
Networks!
With the growth in high bandwidth applications, such as storage and video in the
work place, network performance is essential. Wireless technology is no longer
lagging behind wired performance.The introduction of the Linksys Business Series
WAP4400N Wireless-N Access Point answers the growing business’need for access,
speed, and security.
The Access Point uses the very latest wireless networking technology,Wireless-N (draft
802.11n). By overlaying the signals of multiple radios,Wireless-N’s “Multiple In,
Multiple Out” (MIMO) technology multiplies the effective data rate.Unlike ordinary
wireless networking technologies that are confused by signal reflections, MIMO actually
uses these reflections to increase the range and reduce“dead spots” in the wireless
coverage area.
The Linksys Wireless-N Access Point lets you connect Wireless-N (802.11n),Wireless-G
(802.11g) or Wireless-B (802.11b) devices to your wired network so you can add PCs to the
network with no cabling hassle. Power over Ethernet (PoE) support makes the Access Point
easy to install -- you can mount the Access Point anywhere, even without ready access to a
power plug. With appropriate PoE support at the other end, you only need to run one cable to
the Access Point to deliver both data and power. Of course, you can also use the included AC
adapter if your installation point has power available nearby.
Moreover, the integrated Quality of Service (QoS) features provide consistent voice and video
quality on both the wired and wireless networks, enabling the deployment of business quality
VoIP and video applications.
To protect your data and privacy, the Linksys Wireless-N Access Point supports both Wired
Equivalent Privacy (WEP) and the industrial-strength wireless security of Wi-Fi Protected Access™
(WPA), encoding all your wireless transmissions with powerful encryption. With the MAC address
filter with advanced logging feature, you both control and stay apprised of who accesses your
wireless network. Configuration is a snap with the web browser-based configuration utility.
The Linksys Wireless-N Access Point with Power Over Ethernet is the best way to add wireless access
to your existing business network.
Complies with IEEE draft
802.11n standards while
at the same time being
backwards compatible with
802.11b and g devices
Standards-based POE (IEEE
802.3af) or External DC
power
MIMO technology uses
multiple radios to create a
robust signal that travels
farther and reduces dead
spots
Support for WMM provides
improved QoS over
wireless connections for
better video and voice
performance
WAP4400N
PRODUCT DATA
BUSINESS SERIES
Features
Draft 802.11n wireless
networking delivers greater
throughput and extended
range, maximizing the
number of wireless clients
per access point for your
small business
Full backwards compatibility
for 802.11b and 802.11g
Easy installation and
configuration web interface
Supports WEP,WPA-PSK,
WPA2-PSK, WPA2-ENT,
WPA-ENT authentication
(802.11i ready)
Adjustable dipole antennas
with MIMO 2x3 diversity
Gigabit Ethernet LAN
interface
Supports Power over
Ethernet (PoE) or external
DC power
Supports SNMP and intuitive
web-based interface
WMM wireless QoS
support - upgradeable to
802.11e
•
•
•
•
•
•
•
•
•
Access Point with Power Over Ethernet
Specifications
Model WAP4400N
Standards Draft IEEE802.11n, IEEE802.11g, IEEE802.11b, IEEE802.3, IEEE802.3u,
IEEE802.3af (Power over Ethernet), 802.1x (Security Authentication),
802.11i - Ready (Security WPA2), 802.11e - Ready (Wireless QoS)
Ports Ethernet, Power
Buttons Reset
Cabling Type UTP CAT 5
LEDs Power, Ethernet, Wireless, POE
Operating System Linux
Setup/Config
WebUI Built in Web UI for easy browser-based configuration (HTTP/HTTPS)
Management
SNMP Version SNMP Version 1, 2c, 3
Event Logging Event Logging
Remote Syslog
Web F/W upgrade Firmware upgradeable through web-browser
Diags: Flash, etc. Diags: Flash, RAM, LAN, WLAN
DHCP DHCP Client
Operating Modes
Access Point Access Point Mode
Wireless
Spec/Modulation Radio and Modulation Type: 802.11b/DSSS, 11g/OFDM, 11n/OFDM
Channels Operating Channels: 11 North America,
13 Most of Europe (ETSI and Japan)
# of Internal Ant. None
# of External Ant. 3 (Omni-Directional)
Transmit Power Transmit Power (Adjustable) at Normal Temp Range:
11b - 16 dBm at 1TX, 19 dBm at 2TX; 11g - 13 dBm at 1TX, 16
dBm at 2TX; 11n - 13 dBm at 1TX, 16 dBm at 2TX
Antenna Gain in dBi 2
Receiver Sensitivity 11.n: 300Mbps at -69dbM, 11.g: 54Mbps at -73dBm,
11.b: 11Mbps at -88dBM
Security
WEP/WPA/WPA2 WEP 64bit/128bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT
Access Control Wireless connection control: MAC-based
SSID Broadcast SSID Broadcast enable/disable
802.1X IEEE 802.1X support
Quality of Service
QoS 4 queues
WMM Wireless priority
General
Load Balancing
New AP detection (used with WPC4400N)
New client detection (used with WPC4400N)
Auto-channel selection
PRODUCT DATA
BUSINESS SERIES
Linksys
A Division of Cisco Systems, Inc.
121 Theory
Irvine, CA 92617 USA
E-mail: [email protected]
Web: http://www.linksys.com
Linksys products are available in more
than 50 countries, supported by
12 Linksys Regional Offices throughout
the world.For a complete list of local
Linksys Sales and Technical Support
contacts, visit our Worldwide Web Site
at www.linksys.com.
Check the product package and contents for specific features supported.Specifications are subject to change without notice. Linksys is a registered trademark or
trademark of Cisco Systems, Inc.and/or its affiliates in the U.S. and certain other countries. Copyright © 2007 Cisco Systems,Inc. All rights reserved.Other brands and
product names are trademarks or registered trademarks of their respective holders.
Model: WAP4400N
Environmental
Dimensions 7.80” x 5.16” x 7.80”
W x H x D (198 x 131 x 198 mm)
Unit Weight 0.84 lb (38 g)
Power 12V 1A DC input, and IEEE802.3af Compliant PoE
Certification FCC, CE, IC
Operating Temperature 32 to 104ºF (0 to 40ºC)
Storage Temperature -20 to 70ºC
Operating Humidity 10% to 85% non-condensing
Storage Humidity 5% to 90% non-condensing
Package Contents
Wireless-N Access Point with PoE
User Guide on CD-ROM
Ethernet Network Cable
Power Adapter
Product Stands
Registration Card
Minimum Requirements
802.11b, 802.11g, 802.11n Wireless Adapter With TCP/IP Protocol Installed Per PC
Switch/Router with Power Over Ethernet (PoE) Support Or PoE Injector when used with POE
Web-Based Configuration Java-Enabled Web Browser
Warranty
3 Years
•
•
•
•
•
•
•
•
•
•
WAP4400N-DS-70108NC-BW
Other manuals for WAP4400N
2
Table of contents
Other Linksys Wireless Access Point manuals
Linksys
Linksys WAP54G - Wireless-G Access Point User manual
Linksys
Linksys WAP51AB - Instant Wireless - Access Point User manual
Linksys
Linksys EtherFast Instant Broadband BEFW11S4 Original operating instructions
Linksys
Linksys WAP55AG - Wireless A+G Access Point User manual
Linksys
Linksys WAP51AB - Instant Wireless - Access Point User manual
Linksys
Linksys WAP4400N User manual
Linksys
Linksys LAPAC2600 User manual
Linksys
Linksys EtherFast Instant Broadband BEFW11S4 User manual
Linksys
Linksys WAP200E Operation manual
Linksys
Linksys WAP54G - Wireless-G Access Point User manual
Linksys
Linksys WAP54GPE - Wireless-G Exterior Access Point User manual
Linksys
Linksys WAP54A - Instant Wireless - Access Point User manual
Linksys
Linksys WAP55AG - Wireless A+G Access Point Original operating instructions
Linksys
Linksys WAP2000 User manual
Linksys
Linksys WAP11 - Instant Wireless Network Access... Original operating instructions
Linksys
Linksys WAP11 - Instant Wireless Network Access... User manual
Linksys
Linksys WAP4400N User manual
Linksys
Linksys LAPAC1750PRO User manual
Linksys
Linksys WAP54G v2 User manual
Linksys
Linksys LAPN300 User manual
