Linksys SPA2100 User manual
!
!
!
!
!
!
!
!
!
PLEASE&READ&
!
"#$%!&%'(!)*+&*,!$%!-(.)!/#'!)*+&-*0/&('(!1!Jive&
Communications&may¬&support&some&features&discussed&
in&this&document2!!
!
3,'*%'!%''!.&(!.+,$+'!4.0&)'+/*/$.+!.(!0.+/*0/!&%!-.(!*!
0.)5,'/'!,$%/!.-!%&55.(/'4!-'*/&('%2!!
!
"#*+6%!-.(!0#..%$+7!8$9':!
LINKSYS / SIPURA SPA-1xxx/2xxx/3xxx
CONFIGURATION GUIDE
Minimum Requirements
•ActiveFreshtelInternetPhoneaccount
ohttp://www.freshtel.net
•BroadbandInternetConnection
o256/64kbpsminimum
•BroadbandModem/Router
oMusthaveanEthernetporttoconnecttotheLinksys.
•AnalogueTelephonewithRJ-11line(DesktoporCordless)
Before You Begin
Please note that all information in this guide is applicable to the SPA-1000,
SPA-2000 and SPA-3000 range. These include the SPA-2000, SPA-2100,
SPA-3000 and SPA-3102.
We recommend you ensure that the latest firmware for this device has been
downloaded and installed. For further information, visit the manufacturer’s
website at http://www.linksys.com
If you are using the Freshtel Internet Softphone on your PC with the same
Freshtel number that you wish to use in your Linksys, we advise you to
uninstall or disable the Freshtel softphone. Your Freshtel account can only be
active at one point on our network at any one time, and having two identical
active accounts will cause conflicts.
If you do not yet have a Freshtel account, you should go to our website at
http://www.freshtel.net and register a new account before starting to configure
the Linksys.
Initial Setup
Before configuration, please refer to the Linksys user guide for further
information on how to connect the device to your home network.
If you require more advice, please refer to our help documents on our website
at http://www.freshtel.net/help or contact Customer Care at [email protected]et.
SPA-1xxx/2xxx/3xxx Configuration
Using your telephone handset obtains the IP address of the ATA:
1. Dial **** to enter the Linksys Configuration Menu
2. Dial 110# to get the IP address of the Linksys
3. Write down the IP address of the Linksys.
4. For some models, you may then need to dial 7932#, then 1#,
then 1 to enable the web server of the Linksys ATA.
Enter the IP address of the Linksys in your browser’s address bar to access
the configuration menu.
Figure 1.1
If you are experiencing difficulty trying to connect to the device at this point, try
step #4 above. If you still have problems after this please refer to the user
guide or contact Linksys Technical Support for further assistance.
VoIP Configuration
Once you have logged into the Configuration Center, click the ADMIN LOGIN
link on the top right hand side of the page. Next, click the ADVANCED link
next to it.
If you have a Linksys ATA with a built-in router, such as the SPA-3102, you
will then need to click the VOICE tab at the top of the page.
For more information regarding each property and option, please refer to the
user manual.
SIP Set-up
Figure 1.2
Figure 1.3
Note: All other settings should be left as default.
1. Click on the LINE 1 tab
2. Enter the following:
a. LINE ENABLE: Yes
b. SIP PORT: 5060
c. PROXY: sip.freshtel.net
d. MAKE CALL WITHOUT REG: Yes
e. ANS CALL WITHOUT REG: Yes
f. REGISTER: Yes
g. REGISTER EXPIRES: 3600
h. DISPLAY NAME: Your FRESHTEL Number
(e.g. 81118111)
i. PASSWORD: Your FRESHTEL Password
j. USER ID: Your FRESHTEL Number
k. USE AUTH ID: No
l. PREFERRED CODEC: G729a
m. USE PREF CODEC ONLY: No
n. DTMF TX METHOD: Auto
o. SILENCE SUPP ENABLE: No
p. FAX CED DETECT ENABLE: Yes
q. NAT MAPPING ENABLE Yes
3. Click on SUBMIT ALL CHANGES
DIAL PLAN Set-up
Figure 1.4
1. Click on the LINE 1 tab
2. Enter the following:
DIAL PLAN:
Dial Plan (Australia only -- user has no local call prefix set)
(*123|*xxxxxxxx|<000:61000>S0|<112:61112>S0|<106:61106>S0|61000S0|61112S0|61106S0|
0[2378][2-9]xxxxxxx|0[4569]xxxxxxxx|611300xxxxxx|611800xxxxxx|6113xxxx|6118xxxx|[1-9]x.)
Dial Plan (Australia only -- user has local call prefix set)
(*123|*xxxxxxxx|000S0<:@gw0>|112S0<:@gw0>|106S0<:@gw0>|001[0-
9]x.|0[4569]xxxxxxxx|0[2378][2-9]xxxxxxx|[2-
9]xxxxxxx|1300xxxxxx|1800xxxxxx|13xxxx|18xxxx|1[4-79]x.)
If you do not know whether you have Local Call Prefix set, refer to the
page titled ‘Setting Local Call Prefix On Your Account’ later in this
document.
3. Click on SUBMIT ALL CHANGES
STUN Set-up
Figure 1.5
1. Click on the SIP tab
2. Enter the following:
a. Handle VIA Received: Yes
b. Insert VIA Received: Yes
c. Handle VIA rport: Yes
d. Insert VIA rport: Yes
e. STUN ENABLE: No
3. ClickonSUBMIT ALL CHANGES
Call Progress Tones
Figure 1.6
1. Click on the REGIONAL tab
2.
Enter the following:
Dial tone: 400@-19,425@-19,450@-19;10(*/0/1+2+3)
Busy Tone: 425@-19;10(.375/.375/1)
Reorder Tone: 425@-19,425@-29;60(.375/.375/1,.375/.375/2)
Ringback Tone: 400@-19,425@-19,450@19;*(.4/.2/1+2+3,.4/2/1+2+3)
MWI Dial Tone: 400@-19,425@-19,450@19;2(.1/.1/1+2);10(*/0/1+2)
Ring1 Cadence: 60(.4/.2,.4/2)
Figure 1.7
Control Timer Values
a. HOOK FLASH TIMER MIN: 0.07
b. HOOK FLASH TIMER MAX: 0.13
Distinctive Call Waiting Tone Patterns
c. CWT8 CADENCE: 30(.2/.2,.2/4.4)
Distinctive Ring Patterns
d. RING 1 CADENCE:
•60(1.5/3.4)
e. RING 3 CADENCE:
•60(1.5/3.4,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.
2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2)
Miscellaneous
Figure 1.8
f. TIME ZONE: GMT+10:00 (or relevant to your area)
g. FXS PORT IMPEDANCE:
220+820||120nF
3. Click on SUBMIT ALL CHANGES
Other manuals for SPA2100
1
This manual suits for next models
3
Table of contents
Other Linksys Network Router manuals
Linksys
Linksys PC22604 - ProConnect II 2604 Switch User manual
Linksys
Linksys QuickVPN - PC User manual
Linksys
Linksys BEFSX41 - Instant Broadband EtherFast Cable/DSL Firewall... User manual
Linksys
Linksys MAX-STREAM EA8250 User manual
Linksys
Linksys WET54GS5 - Wireless-G EN Bridge Operation manual
Linksys
Linksys MAX-STREAM EA8300 User manual
Linksys
Linksys Instant PowerLine PLEBR10 User manual
Linksys
Linksys RTP300 - Broadband Router With 2 Phone Ports Instruction Manual
Linksys
Linksys E56000 User manual
Linksys
Linksys VELOP User manual
Linksys
Linksys RV082 User manual
Linksys
Linksys WRT54GH User manual
Linksys
Linksys X2000 User manual
Linksys
Linksys MR2000 Series User manual
Linksys
Linksys MAX-STREAM EA8300 User manual
Linksys
Linksys EG0801SK - EtherFast Network Starter User manual
Linksys
Linksys Velop MX4000 Series User manual
Linksys
Linksys BEFVP41 - EtherFast Cable/DSL VPN Router Original operating instructions
Linksys
Linksys BEFSR41 - EtherFast Cable/DSL Router User manual
Linksys
Linksys WET54Gv2 User manual
