Linear 1050 User manual

OPERATIONAL CHECK

To check operation, move back a reasonable distance (about 50 ft.) and press the

transmitter button. Operation should be reliable at this distance but

environment and location of both the transmitter and receiver will affect the

range. If the transmitter is stowed well out of sight, it may be necessary to

remove it from its mounting and hold near the windshield. Try different locations

and positions. If operation is still unsatisfactory, the problem may be isolated by:

Checking the door operator.

If the door will not open when the wall button is

pressed, the problem is likely to be the operator. If the door will open by pressing

the wall button, but not when the radio control button is pressed, the problem is

probably in the radios.

Replacing the transmitter battery.

If after performing the above operational

checks, the controls still do not function, they should be returned to your dealer for

repair or replacement.

CAUTION:

Any changes or modifications in intentional or unintentional

radiators which are not expressly approved by LINEAR CORPORATION could

void the user’s authority to operate this equipment. This applies to intentional

and unintentional radiators certified per part 15 of the F.C.C. rules and

regulations.

LINEAR CORPORATION

2055 Corte del Nogal •Carlsbad, CA 92009

(760) 438-7000

INSTALLATION INSTRUCTIONS

DIGITAL TRANSMITTER MODEL 1050

Congratulations! You have just purchased a Linear Digital Transmitter, which we

believe to be the finest product of its kind on the market. With a little care this

transmitter should provide you with many years of excellent service. Please take a

moment to read the following instructions and you will find that setting your new

transmitter will be quite an easy matter.

ACCESSING THE CODE SWITCH

On the model 1050 the side of the transmitter is removable. Squeeze the ends

of the transmitter case or twist a coin in the slot provided, then pull the side to

remove it. This will expose both the code switch and battery compartment.

INSTR,INSTL,MC1050,1CH,XMTR

LINEAR P/N: 216908 A

INK: BLACK

MATERIAL: 20 LB. MEAD BOND

SIZE: 9.000" x 3.500"

SCALE: 1-1

SIDE 1 OF 2

SELECTING A CODE

You may set your transmitter to any code you desire but be sure that the code you

set matches the code that has been set on your radio receiver. The digital code is

determined by the positions of the 10 small switches numbered 1 through 10

located in the receiver and transmitter. Any combination of ON (CLOSED) or OFF

(OPEN) positions can be selected by using a small screwdriver or paper clip.

(NOTE: The switches are in the “On” position when the side next to the number

is pressed in.) In setting your own personal code we strongly urge that several

coding schemes be avoided: ALL ON; ALL OFF; 2,4,6,8,10 ON; 1,3,5,7,9 ON.

These positions are similar to our or other manufacturer’s test positions, or are

frequently used. Once the code has been set, check the operation and replace

the case side.

TRANSMITTER INSTALLATION

The transmitter is completely self contained, including battery, and can be

operated while mounted in the car. It is supplied with a clip for attaching to the

sun visor, if desired. If the clip is used attach to the case by sliding it into the

recess provided on the back of the transmitter until the small dimples fit into the

holes in the clip.

TRANSMITTER BATTERY REPLACEMENT

Replacement battery - 9 volt NEDA 1604 (Eveready 216 or equivalent).

The battery in the transmitter can be checked or changed by removing side of the

transmitter. Refer to the directions under “accessing the code switch” for battery

replacement.

TO REPLACE OR ADD A SET

A replacement or new transmitter or receiver may be purchased by specifying

the Model Number and the RF frequency designated on the identification label.

The RF frequency is set at the factory and must not be adjusted in the field. The

digital code can be matched to the companion receiver or transmitter by

following the above procedure.

INSTR,INSTL,MC1050,1CH,XMTR

LINEAR P/N: 216908 A

INK: BLACK

MATERIAL: 20 LB. MEAD BOND

SIZE: 9.000" x 3.500"

SCALE: 1-1

SIDE 2 OF 2

Other Linear Transmitter manuals

Linear

Linear 3022 User manual

Linear

Linear MVP User manual

Linear

Linear GT-31 User manual

Linear

Linear MULTI-CODE 1051 User manual

Linear

Linear DX DXT-61 Technical manual

Linear

Linear DT-3+1 Administrator guide

Linear

Linear Delta-3 DTG User manual

Linear

Linear MULTI-CODE 4120 User manual

Linear

Linear Delta-3 Series Administrator guide

Linear

Linear WT00Z-1 User manual

Linear

Linear Mini-Code 3083 User manual

Linear

Linear DXT-61/EC User manual

Linear

Linear DT-2A Administrator guide

Linear

Linear DIGITAL TRANSMITTER GT-30 User manual

Linear

Linear LMT-1 User manual

Linear

Linear LMT-1 User manual

Linear

Linear AT71-250 User manual

Linear

Linear MegaCode MCT-11 User manual

Linear

Linear Supervised Emergency Alarm Transmitter... User manual

Linear

Linear D-22B Administrator guide

Linear

Linear MegaCode ACT-21 User manual

Linear

Linear DXS-32/EC User manual

Linear

Linear ET-2 User instructions

Linear

Linear DXS-64 User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction