Linddana TP 160 Installer manual

Linddana A/S • Ølholm Bygade 70 • DK-7160 Tørring • Tel. + 5 7580 5200 • [email protected] • www.tp.dk

User Manual

Spare parts catalogue

for the TP 160 wood chipper in

the park series

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



1Introduction

Congratulations on your new TP wood chipper.

Linddana produces TP wood chippers of the finest quality by using the most modern production

technologies, i.a. laser cutting, CNC technology and robot technology in bright and open production

facilities.

For safety reasons and in order to get maximum pleasure from the wood cutter, it is important to

read these instructions before use.

The user manual explains about safety, use and maintenance so that the work with the wood chipper

will be safe and profitable.

This manual has been translated from Danish.

Linddana A/S

Jørgen Due Jensen, Managing director

Your distributor is always available with spare parts, advice and guidance.

Distributor stamp

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



2EU declaration of conformity.

Manufacturer:

LINDDANA A/S, Ølholm Bygade 70, Ølholm, 7160 Tørring, Denmark

hereby declares that

______________________________________________

Wood chipper:

is in concordance with the provisions of the Machine Directive (Directive 06/42/EC) and with the

national legislation which translates this directive;

is in concordance with the following other EC Directives:

2000/14/EC

Furthermore it is stated that

EN 13525 (harmonised standard), has been used.

Title: Managing director

Name: Jørgen Due Jensen

Ølholm, 14 September 2010

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



3Table of content

Introduction .......................................................................................................2

EU declaration of conformity............................................................................3

Table of content .................................................................................................4

Use......................................................................................................................5

Mounting instructions........................................................................................6

Safety instructions............................................................................................10

Operation of the machine ................................................................................14

Maintenance.....................................................................................................16

Special instruction for TP 160 MOBILE........................................................26

Special instruction for TP 160 TRACK.......................................................30

Hydraulics diagram, TP 160 without revolution guard..............................31

Hydraulics diagram, TP 160 with revolution guard...................................31

Hydraulics diagram, TP 160 TRACK with revolution guard ....................32

Instruction for revolution guard TP PILOT 01..........................................33

Troubleshooting for wood chipper TP 160..................................................40

Guarantee obligation for wood chipper.......................................................41

Technical data wood chipper .......................................................................43

Accessories....................................................................................................46

Spare parts catalogue...................................................................................47

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



4Use

The TP 160 wood chipper is designed for stationary wood chipping in the form of braches etc.

The machine must not be used for materials containing stone, metal or other foreign bodies. These

foreign bodies can in the best case dull the knives and in the worst case break the machine. Knives

and anvil can break when stone or metal comes in between them.

The machine must not be used for wood chipping of wood containing nails, screws, arming etc.

When feeding branches you must stand next to the feeding hopper (see fig. 1).

The branches can be thrown around when the retract rollers get a hold of them.

Logs must be fed into the machine from the back (see fig. 2).

Figure 1 Feeding branches Figure 2 Feeding logs

Remember to keep the knives and anvil sharp, it makes feeding easier and gives a better quality

chips, and besides it lovers the use of fuel considerably.

The machine must be inspected daily, meaning the rotor housing must be opened and the rotor,

knives, anvil etc. must be inspected. By doing this you prevent unexpected stops and prolong the life

of the machine.

The tractor or trailer upon which the machine is mounted must always have the brakes activated

during work.

The machine must not:

•Be used for other materials than wood

•Be used to push trees, stubs etc.

There must not be equipment like forest chains, axes, chain saws etc. in the feeding hopper.

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



5Mounting instructions

5.1 Before use

The machine is equipped with a lifting point which is to be used when lifting the machine with a

crane or any other hoisting device (ground assistance) (see Figure 3). The machine can also be lifted

with a fork lift truck. This is done by using the holes made for this purpose on both sides of the foot

(see Figure 4). Make sure that the forks of the truck are put all the way through otherwise the

machine can tip over. The TP 160 MOBILE is mainly transported on the trailer wheels, but it can

also be lifted with a fork lift truck (see Figure 5). The TRACK model can be lifted with a forklift

truck on a pallet. (see Figur 6)

Figure 3 Lifting point on the machine

Figure 4 Lifting with a fork lift truck

Lifting point

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



Figure 5 Lifting with a fork lift truck

Figur 6 Lifting with a fork lift

Store the manuals for the PTO member with this manual in the manual box on the machine.

Min. 2 m

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



Before operation you must check that the wood chipper cleared of foreign bodies. The machine

must be uncoupled from the tractor’s PTO, for the MOBILE and TRACK models, the key must be

removed from the ignition before opening for the rotor. Check that the rotor is at a complete

standstill. Turn the ejector tube so that it faces the opposite direction of the rotor housing (see fig.

7). Loosen the bolts that hold the upper and lower rotor housing together. Lift the top part of the

rotor housing up until the ejector tube rests on its own. Turn the rotor a few times by hand. Remove

any foreign bodies.

Check that the gap between the knives and the anvil is correct = 0,5 – 0,9 mm. The knives have a

fixed knife position = 10 mm. Check that the knives are not rubbing on the anvils.

Lift the top part of the rotor housing back in place and tighten the bolts.

Check that all bolts, nuts and screws are tightened properly.

Remember to lubricate all the lubrication points (see maintenance schedule, page 16).

Old hydraulics and motor oil and used oil filters and air filters must be handed in at an approved

receiving station.

5.2 Mounting instruction

The machine is designed to be mounted on the tractor’s three-point-suspension or trailer mounted

with its own engine.

Machines for mounting on the tractor’s three-point-suspension is delivered with a PTO axle with

either 1 3/8" - 6 splines or 1 3/8" - 21 splines.

At certain types of tractors a PTO axle with 1 3/8" - 21 splines is used.

The PTO axle must be mounted with free running on the machine side.

Linddana uses Walterscheid W400 with free running which comes with the machine.

The length of the PTO axle has to be adapted to the tractor following instructions from the supplier

of the PTO axle. See the attached manual for the PTO axle.

The machine must stand on a plane, horizontal surface during use and the tractor mounted machines

must be attached to the tractor’s three-point-suspension (see Figure 8). The tractor’s brakes must be

properly activated. Trailer mounted machines must also have their brakes activated (see Figure 9).

When starting the machine: Attachment must be done with the motor running at idle speed or at as

few revolutions as possible in order to avoid overloading of the PTO axle, gear box, tractor and

wood chipper.

Figure 7

Position of ejector tube when

opening rotor housing

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



Figure 8 TP 160 PTO three-point-suspension Figure 9 TP 160 MOBILE hand brake

Hand brake

Three-pointsuspension

Linddana A/S, Ølholm Bygade 70, DK-7160 Tørring, Telefon +45 75 80 52 00 Fax +45 75 80 54 11

User Manual: TP 160 14.09.2010 Email: t[email protected]



6Safety instructions

6.1 Safety regulations

•Use hearing protectors, safety goggles or a similar eye protection, close fitting safety clothing

and safety shoes.

•When working near roads it can be prudent to wear a west which reflects the light to be more

visible to the other road-users. The displaying of signs must be in accordance with the Road

Traffic Act.

•Minimum age for users of the machine is 18, for training and under surveillance from an adult

the age is 16.

•During operation, all body parts must be kept away from the feeding hopper and any

moveable parts of the machine.

•Any material that is stuck between the retract rollers must not be attempted removed by hand

before the spring has been demounted and the roller part opened.

•Always stand next to the feeding hopper during feeding of the machine. Always observe the

terrain conditions around the machine. It can be dangerous to fall near the machine!

•Before starting the machine check that the safety devices are working properly. Especially the

stop and return functions on the operation bow.

•The machine must not be started without the ejector tube mounted to the machine.

•Never use the machine in closed or poorly ventilated spaces, because of the danger of carbon

monoxide poisoning.

•The top part of the machine as well as all other shielding must not be opened/removed before

the rotor disc is completely immovable and the tractor’s motor is stopped.

•Always stop the machine and the tractor during inspections, service or repairs. The machine

must be uncoupled from the tractor’s PTO.

•Tractor mounted machines have to be on the ground before service or repairs are done.

•Always remove the keys from the machine and/or the tractor before leaving it.

•After maintenance and repairs, the machine must not be started before all bolts are tightened

and all safety devices are mounted.

•Three-point mounted machines must be coupled to the tractor’s three-point- suspension

before use.

•The maximum rpm for the machine (1000 rpm) must not be superseded.

•The transmission axle’s tube shielding and covering must always be intact. Safety chains on

the transmission axle have to be properly mounted.

•The length of the PTO axle has to be adapted to the tractor according to the

recommendations from the supplier of the PTO axle.

•The ejector tube must not point towards people or areas where there are people. There is a

safety distance of 20 m. in the direction where the chips are thrown.

•AT DANGER: PUT THE OPERATION BOW IN NEUTRAL (See Figure 11)

This manual suits for next models

Table of contents

Other Linddana Chipper manuals

Linddana

Linddana TP Series User manual

Popular Chipper manuals by other brands

Craftsman

Craftsman 79964 owner's manual

Frontier

Frontier WC1208 Operator's manual

Viking

Viking GE 150 instruction manual

Victory

Victory WC-8H Operator's manual

GTM Professional

GTM Professional GTS 1300 user manual

Yardbeast

Yardbeast YB3514 user manual

Patriot

Patriot Electric Motors parts list

Echo

Echo CH5540 owner's manual

DOSKO

DOSKO 13-21T-13H owner's manual

Craftsman

Craftsman 486.24516 Operator's manual

Garland

Garland 1480 TQG instruction manual

Vermeer

Vermeer BC160XL Operating and safety instructions

Value Leader

Value Leader z9400 Assembly, operation and parts manual

Timberwolf

Timberwolf TW 230HB instruction manual

Salsco

Salsco 600PTO Operator and parts manual

Cub Cadet

Cub Cadet 24A-424M710 Operator's manual

Champion

Champion 91050 Owner's Manual and Operating Instructions

Kellfri

Kellfri 13-WC17H2 operating instructions