Lightmen STAGE 100F User manual
STAGE 100F
1
Content List
Page Content
1 Content List
2 Product Introduction
7 Safety and Maintenance Information
10 Installation
11 Control Menu
13 DMX Connection and DMX Protocol
14 Wireless Control Settings
15 Setting Options by RDM
17 Unique Features
18 Dimensions Drawing
Technical Specification
19 Declaration of Conformity
2
1. Product Introduction:
1.1 Before unpack the fixture, please make sure that the packing is in good
condition, following items will be found in the box:
Stage 100F
This users guide
3m DMX cable
1.5m power cable with True1
Safety chain
1.2 Specifications
Source
Light source: 100W Warm white or Cool white LED engine
CT: 3200K(WW) 5600K(CW)
CRI: 97(WW), 97(CW)
LED life: 50,000 hours （under 80% output condition）
Continuous Operation Test: IF=1080mA Ta= 25C (with Al-fin) x1000hrs
IF=1080mA Tj=140C (with Al-fin) x1000hrs
Low Temperature Storage Test: -40℃x 1000 hours
High Temperature Storage Test: 100℃x 1000 hours
Moisture-proof Test: 85℃, 85% RH for 500 hours
Thermal Shock Test: -40℃x 30 minutes & 100℃x 30 minutes, 100 cycles
Flux on small angle 23°: 2820lux@3m | 1000lux@5m (WW)
2910lux@3m | 1030lux@5m (CW)
Flux on big angle 90°: 510lux@3m | 183lux@5m(WW) 542lux@3m
| 193lux@5m (CW)
Control: Via DMX 512 protocol
Remote Control via wireless
Via RDM
3
Optical System
Beam angle: 23°-90°
Lens Type: HQ Glass optics
Body
Body: Sturdy die-cast aluminum body conceived for long-time
durability
Body Color: Black/White
Features
DMX channels:2/4/1CH
RDM function is to change DMX address, display flip, X/Y Reverse,
show led voltage, current and power consumption info.
Software upgrade via DMX only
Hibernation when lost DMX for preset time
Indicate temperature info of led
Fan speed auto change according to temperature
Dimmer Curve: 4 different dimmer curve available(Exponential, Linear,
INV-Exp, and S-Curve).
Display
Display: Black OLED high resolution display with friendly English menu
Auto lock
Flip
Back-up communicating IC
4
Dimming
Dimmer Curve provides 4 dimming options（see below figure）
Linear: the increase in light intensity appears to be linear as DMX value
is increased.
Exponential:the light intensity control is finer at low level, coarser at
high level.
In-Exp:the light intensity control is finer at high level, coarser at low
level.
S-Curve:the light intensity control is finer at lower and higher level,
coarser at medium level.
Linear
Exponential
In-Exp
S-Curve
5
1.3
Description of the Device
1. Bracket
2. Housing
3. Barndoor
4. Lens
5. Barndoor holder
6. Light shield panel
7. Wireless DMX Antenna
6
8. 5-Pin DMX 512 output
9. 5-Pin DMX 512 input
10. Power In TRUE1
11. Power Out TRUE1
12. Fuse
13. Handle
14. Knob
15. Buttons
16. Dimmer knob
17. Display
7
2. Safety and Maintenance Information
2.1 Safety Info
Before operate this unit, please carefully read this users guide
and keep if needed in future. It’s necessary to respect following
rules.
The disposal of the device after life-cycle could damage the
environment. Need to take it to special company for recycling or
return to authorized dealer.
The products referred to in this manual conform to the
European Community Directives and are therefore marked with
CE logo.
Keep this device away from children and unauthorized users,
the manufacturer will not take responsibility for the damage
due to any disregard of the information provided in this manual
and wrong operation.
Before operate the device, please make sure the fixture is in
good housing, ensure pan and tilt can rotate in its complete
range.
--0.5m
Please make sure minimal 0.5m distance need to kept between
the fixture to any flammable material.
The device can only run with 100-240v voltage, 50/60Hz power,
don’t connect to any other wrong power. Disconnect the device
from main power before open the shield or maintenance.
The device is designed only for indoor usage, please keep it
away from moisture. Do not expose the device under the sun or
directly to any other lighting source.
Never look directly into the projecting lens when the fixture is
power on, the light may trigger epileptic seizures in
photosensitive persons or persons with epilepsy. Especially at
beam effect, extreme caution and observance of these safety
instructions is mandatory.
8
Don’t put or install the device on a surface that subject to
vibration or bumps.
Ta=45℃
The device is supposed to work in the temperate range -20° to
+45°C, do not use the device when the temperate exceed this
range.
The lens, shield need to be replaced when obviously broken,
never use the device when the shield is not completed closed.
Safety I class device, need to be earth connected.
When the fixture is hanged overhead, the safety rope must be
fixed to the bottom of the device to the appropriate fixing point.
Always carry the device by the bracket, do not take the body
directly for transportation.
2.2 Maintenance
2.2.1 Operation only allowed to qualified person, damages due to unprofessional
operation or remove of any parts inside will not be considered in warranty
service. There are no serviceable parts inside the device or package, service only
leaves to authorized dealers.
2.2.2 Never allow the optical components contact with oil, fat or any other
liquid.
2.2.3 A regular clearance of the device is needed for long-term usage, this is very
helpful to maintain the lifetime and brightness need to use a soft and lint-free
cloth to clean the optical system, fan and air flowing tunnel.
9
2.2.4. Trouble Shooting
Problems
Possible reasons
Checking or solutions
Device not power
up
TRUE1 or power cable
damaged
Faulty power supply
Change a good power cable to
try
Replace new power supply
LED off
Temperature
protection
Fan not working
Faulty LED
Dimmer and strobe
set at 0
Faulty power supply
Check the temperature from
menu
Check the fan speed info from
menu
Replace new LED
Set dimmer channel at 255 and
strobe channel at 0~5
Replace new power supply
Device not
response to DMX
Faulty communication
IC
Faulty display PCB
Wrong DMX
addressing
Faulty DMX cable
Replace the IC with back-up
one in the display PCB
Replace new display PCB
Check the address and setting
Change to a good DMX cable
2.2.5 Replacement of the fuse
Need to replace with same type and rating(T 2A-250V), which originally installed
in the device.
Step One: Unplug power cable from main power.
Step Two: Unscrew the fuse holder out of the housing with a screwdriver.
Step Three: Remove the broken fuse and replace with an exact same type of new
fuse.
Step Four: Insert the fuse holder back to the housing and screw tight and
reconnect power.
This manual suits for next models
4
Table of contents
Other Lightmen Dj Equipment manuals
