Setup Instructions
Before programming the device, it is recommended that you press the RESET button
using a pointed object such as a paper clip or pencil. The screen will display CODE.
Setting Date and Time
1. Hold the TIME button until the year setting appears flashing.
2. Select the year by using the BOOST/ADV buttons.
3. Press the TIME button to move on to the month setting.
4. Set the correct month using the BOOST/ADV buttons.
5. Press the TIME button to move on to the day of the month setting.
6. Set the correct date using the BOOST/ADV buttons.
7. Press the TIME button to move on to the time setting.
8. Set the correct hour using the BOOST/ADV buttons.
9. Press the TIME button to move on to the minute setting.
10. Set the correct minutes using the BOOST/ADV buttons.
11. Press the TIME button and the time/date settings are complete.
Timer Programming
1. Hold the PROG button for 3 seconds. The 7 Day Program mode will display.
2. Press the ADV button to scroll through the program modes, as follows:
3. Once selected, press the PROG button to advance to setting the ON time for program 1.
4. Adjust the hour using the BOOST/ADV buttons, then press the PROG button and do the same again
to set the minutes.
5. Press the PROG button again to advance to setting the OFF time for program 1.
6. Repeat processes 4&5 to set the OFF timings.
7. Press PROG to advance to program 2 and repeat the process again.
8. There are 4 programs available per day that can be set or left blank if not required.
9. Press PROG to exit programming mode. The PROG button can be pressed and held for 3 seconds
at any point during programming to return to operating mode.
10. NOTE: The main switch needs to be set to the down position with the red line showing on top (ON)
for the programmer to work and switch the load.
• Mo Tu We Th Fr Sa Su - 7 Day mode - Enables setting the same timer ON/OFF settings for
each week day.
• Mo Tu We Th Fr - 5 Day mode - Enables setting the same timer ON/OFF settings for each
week day.
• Sa Su - Weekend mode - Enables setting the timer ON/OFF settings for weekend days only.
• Mo - Individual day mode - Enables setting dierent timer ON/OFF settings for each day of
the week.
Pack Contents
• Instruction leaflet
• 7 Day programme time switch
• Cable clamp set
• 2 x 3.5mm x 35mm socket box screws
Display screen
Programme Set
Time and
date set
Reset Button
Power Indicator
Output Indicator
Boost button will
override current
programme in hour
increments as selected.
2 hours max.
Advance button
will move to
the next set
programme
Features / Specifications
Switched fused spur with programmable timer with display, 1 or 2 hour boost function & override
facility.
•Program settings: 7 Day, 5 Day (Week days only), 2 Day (Weekend only)
•Up to 4 x ON/OFF switch timings per day.
•Battery back-up in case of mains power failure
•LED indicators for Mains Power ON & Output Power ON
•1 or 2 hour ‘Boost’ function
•‘Advance’ override boost - switches o at next programed timer event
•Front cable outlet for connection of load with cable clamp
•Double pole switch
•Fits 25mm back box
•Replaceable BS1362 fuse at front
•220-240V A.C
Double pole switch BS 1362 (1” x 1/4”) fuse
Installation
•This unit should only be installed by a qualified electrician, adhering to the local regulations and
guidance covering the installation.
•The spur is designed to fit a 1 gang 25mm deep (min) back box.
•The unit can be used as part of a ring main and can accept 2 x 2.5mm T&E conductors per terminal.
•An earth loop through connector is supplied if required.
•If the unit is installed in a metal back box, earthing of the back box is necessary.
•Switch o the mains power supply at the fuse board before connecting the unit.
•Connect the supply to L IN & N IN. Connect the load to L OUT & N OUT.
•The load cable can be fed through the front cable exit and should be clamped using the supplied
cable clamp.
Suitable for use with:
•Resistive loads (3kW max) - such as Immersion Heaters
•Incandescent / Halogen Lighting (700W max)
•Fluorescent Lighting (500W max)
•CFL Compact Fluorescent Lighting (80W max)
•LED Lighting (150W max)
•Not suitable for use with discharge lighting
Note:
The time is a 24hr clock.
Holding down the ‘BOOST’ or
‘ADV’ button will advance or
decrease the settings more
Important Information
This timer is only suitable for installation in systems where it is constantly powered. It may not be suitable
for installation into a system where the mains supply is regularly lost or switched o such as Economy 7
or 10 systems. It can be used on Economy 7 or 10 systems where the power is not switched o at any
point, but just switched between taris.
Regular loss of power to the timer may result in the battery becoming over-discharged and errors may
occur in the programming and with the reliability of the internal clock.
The battery within this product is designed to retain the clock timing and program setting during the
event of an occasional power cut.
