Light4Me VENOM SPOT RING 200W User manual
1
VENOM SPOT RING 200W
INSTRUKCJA OBSŁUGI
USER MANUAL
2
1 SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do not
switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the
case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only
handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell or smell may arise. This is a normal process and does
not necessary mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with
wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced
by the manufacturer of his service agent or a similar qualified person in order to avoid a hazard.
3
2 UNPACKING
Thank you for choosing our LED 200W moving head light. For your own safety, please read this
manual before installing the device. This manual covers the important information on installa-
tion and applications. Please install and operate the fixture with following instructions. Mean-
while, please keep this manual well for future needs.
The LED 200W is made of a new type of high temperature strength of engineering plastic and
cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly fol-
lowing CE standards, complying with international standard DMX512 protocol. It’s available in-
dependently controlled and linkable with each other for operation. And it is applicable for large-
scale live performances, theater, studio, nightclubs and discos.
The 200W Moving head light which features high brightness and stability. Please carefully un-
pack it when you receive the fixture and check whether it is damaged during the transporta-
tion. And please check whether the following items are included inside the box:
4
3 FEATURES & SPECIFICATIONS
Features
·200W High Output White LED
·50,000 hours lifespan and low power consumption
·Beam Angle 15°, focus function
·High light output, LUX8000@5M at White light
·Temperature protect function, when the internal Temperature is up to 40° then the fans
begin to work, when the internal temperature is up to 70°and the brightness reduce half.
·Color Wheel: 7 colors +white, color fine tuning, rotation with variable direction and speed
·1 static Gobo Wheel: 8 gobos +white, wheel rotation and shake
·1 Rotation Gobo Wheel: 6 gobos +white, wheel rotation and shake
·Prism: 3-facet Prism, bi-directional rotatable at variable speeds
·High speed strobe effect with 1-25 flashers per second
·Internal program available
·19/17 DMX Channels USITT DMX-512
·DMX 512, master-slave and sound activated controllable or auto operation
·Colorful LCD display
·Efficient low noise fan cooling system
·PowerCon IN/OUT
·3-pin & 5-pin XLR connectors IN/OUT
·Two 1/4 turn fastening Omega Clamps
·IP 20 protection rating
Specifications
Input Voltage: AC90-260V 50/60Hz
Light Source: 200W High Output White LED with led round 24X0.5W RGB 3-in-1
Control Signal: DMX 512, master-slave and sound activated or auto operation
Control Channel: 19/17 DMX Channels USITT DMX-512
Power Consumption: 315W
Dimensions: 328(L)*220(W)*482(H)mm
Packing size: 365(L)*290(W)*600(H)mm
Net Weight: 13.50kg,Gross Weight: 15.50kg
5
4 PHOTOMETRIC DATA
6
5 OPERATION INSTRUCTIONS
∙The moving head is for spot effect for on-site decoration purpose.
∙Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So
make sure to operate the fixture until it is in normal temperature.
∙This light should be keep away from strong shaking during any transportation or move-
ment.
∙Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
∙Don’t expose the fixture in overheat, moisture or environment with too much dust when
installing it. And don’t lay any power cables on the floor. Or it might cause electronics
shock to the people.
∙Make sure the installation place is in good safety condition before installing the fixture.
∙Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture.
∙Make sure the lens are in good condition. It’s recommended to replace the units if there
are any damages or severe scratch.
∙Make sure the fixture is operated by qualified personnel who know the fixture before us-
ing.
∙Keep the original packages if any second shipments is needed.
∙Don’t try to change the fixtures without any instruction by the manufacturer or the ap-
pointed repairing agencies.
∙It is not in warranty range if there are any malfunctions from not following the user man-
ual to operate or any illegal operation, like shock short circuit, electronic shock, lamp
broke, etc.
7
6 INSTALLATIONS
Cautions: For added protection mount the fixtures in areas outside walking paths, seating ar-
eas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 items the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an ap-
propriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept
at least 0.5m (1.5ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental dam-
age and/or injury in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including amongst oth-
ers calculating working load limits, a fine knowledge of the installation material being used,
and periodic safety inspection of all installation material and the fixture. If you lack these qual-
ifications, do not attempt the installation yourself. Improper installation can result in bodily in-
jury.
Be sure to complete all rigging and installation procedures before connecting the main power
cord to the appropriate wall outlet.
Clamp Mounting: The LED moving head provides a unique mounting bracket assembly that
integrates the bottom of the base, and the safety cable rigging point in one unit (see the illus-
tration below). When mounting this fixture to truss be sure to secure an appropriately rated
clamp to the included omega bracket using a M10 screw fitted through the center hole of the
“omega bracket”. As an added safety measure be sure to attached at least one properly rated
safety cable to the fixture using on of the safety cable rigging point integrated in the base as-
sembly.
8
Regardless of the rigging option you choose for your LED moving head, always be sure to se-
cure your fixture with a safety cable. The fixture providers a built-in rigging point for a safety
cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging
point for the safety cable and never secure a safety cable to a carrying handle.
9
7 DMX-512 CONTROL CONNECTIONS
Connect the provided XLR cable to the female 3-pin XLR & 5-pin XLR output of your controller
and the other side to the male 3-pin XLR & 5-pin XLR input of the moving head. You can chain
multiple moving head together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram below.
For installations where the DMX cable has to run a long distance or is in an electrically noisy
environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps
in preventing corruption of the digital control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3, which is then
plugged into the output XLR socket of the last fixture in the chain. Please see illustrations be-
low.
.
10
8 MENU OPERATIONS
MENU
Address Set [Set Address Numbers]
[DMX]
Run Mode [AUTO] Auto 1- Auto 4
[SOUND]
[MANUAL] Manual Test Function and Operation
Pan reverse
Tilt reverse
Display
Screen Reverse
Setup [Advanced Setting] Channel (19/17CH Select)
Sensitivity (01-100)
Motor zero
Reset
Factory Set
Ver V1
System Information DMX Address
Temperature
Table of contents
Languages:
Other Light4Me Lighting Equipment manuals
Light4Me
Light4Me VENOM BEAM 250 User manual
Light4Me
Light4Me BELKA LED COB PAR 4x30W User manual
Light4Me
Light4Me VENOM STROBE User manual
Light4Me
Light4Me HYPNO PAR User manual
Light4Me
Light4Me HYPER BEAM User manual
Light4Me
Light4Me AIRSHIP 2 User manual
Light4Me
Light4Me BUBBLE LED User manual
Light4Me
Light4Me JET 2000 User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
