LG AB-BL200X User manual
Owner's Manual
e-MultiBoard Mounting Bracket & Stand
Please read the safety information carefully before using the product.
AB-BL200X
AB-BP200X
AD-BX200X
AD-BL200H
AD-BP200H
P/NO : MFL63640508(1203-REV02)
2
Accessories
4 Guide Spacers
Owner's
Manual
4 Guide Spacer Screws
(M8 x 32mm)
2 Bracket Screws
(M8 x 100mm)
2 Nuts
e-MultiVision Bracket AB-BL200X, AB-BP200X
E-MultiBoard Mounting Bracket – Landscape
AB-BL200X
E-MultiBoard Mounting Bracket – Portrait
AB-BP200X
e-MultiVision Stand AD-BX200X, AD-BL200H, AD-BP200H
Wrench
Stand Frame Horizontal
4 Nuts
4 Screws (M8 x 15mm)
Stand Frame bottom
Stand Frame Vertical
2 Screws
(M8 x 15mm)
4 Screws
(M8 x 100mm)
AD-BX200X AD-BL200H, AD-BP200H
2 Nuts
3
ENGLISH
After reading the manual, please keep it handy for future reference.
- If you are a professional installer, please read this manual carefully before installing the product.
- After installing the product according to the manual, ensure that the user also reads the manual carefully.
Safety Precautions
Warning
The product should be installed by a qualified professional
specified by the retail store.
Installing the product without a qualified professional is dangerous and may
cause injury.
The product should be installed where its weight can be
supported.
If the product is installed on a weak surface, the product may fall and cause
injury.
When moving or replacing the product after installation,
contact a qualified installer specified by the retail store.
Installation or movement of the product must be carried out by a skilled
professional. If an unqualified person moves and installs the product, this may
cause safety issues.
Prior to installing the product, arrange the power cable and
signal cable to prevent damage during the installation.
Damaged cables may result in a fire, electric shock or damage to the product.
Do not hang on the product or impact the product.
The product may fall and cause injury.
Do not clean the product with wet towels, and do not use a heater or
humidifier underneath the product.
Moisture permeating into the product, including through steam and heat, may
result in a fire, electric shock or damage to the product.
Make sure that the power cord is removed from the outlet
before installing the product.
Otherwise, it may cause an electric shock or a fire.
Keep the product away from sprinklers, sprinkler sensors, high-
tension wires and power sources. Do not install the product in a
location where vibrations or shock impacts are likely to occur.
Wear working gloves when installing the product. Do not use bare
hands.
Otherwise, it may cause injury.
Caution
Follow the instructions in the manual to install the product.
If you do not follow the instructions, the product may not be installed properly,
causing serious injury or damage to the product.
To install or adjust the height of the product, two or more people
are needed.
If you try to install or move the product alone, it may fall and cause injury or
damage to the product.
Before installing the product, check whether the wall is strong
enough to hold the product.
Installing the product on a wall that cannot hold its weight may cause safety
issues.
To stand the product upright, two or more people are
needed.
If you try to stand the product up alone, it may fall and cause an injury due to
its weight.
Do not stand or hang on the product when upright.
The product may fall and cause injury.
Place the product on a flat, hard floor.
Leaving the product on a carpet or cushioned surface may cause the
product to fall and result in an injury.
Do not place the product on an unstable shelf or on a slanted or
vibrating surface.
The product may fall or turn over and cause injury.
If the external surface has stains or fingerprints, gently wipe the stained area only.
Do not apply excessive force to remove the stain. This may cause scratches or discoloration.
4
When moving or lifting the monitor, read the
following to prevent the monitor from being
scratched or damaged and for safe transportation
regardless of its type and size.
It is recommended to move the monitor in
the box or packing Cover that the monitor
originally came in.
Before moving or lifting the monitor,
disconnect the power cord and all cables.
Hold the top and bottom of the monitor frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
Avoid touching the screen at all times, as this
may result in damage on the screen.
CAUTION
When transporting the monitor, do not expose
the monitor to jolts or excessive vibration.
When transporting the monitor, keep the
monitor upright, never turn the monitor on its
side or tilt towards the left or right.
When transporting the monitor by hand,
hold the monitor as shown in the following
illustration.
When the product is carried upright, 2 persons
carry by holding the bottom and top of the
front, and when it is being put down, put down
carefully for the panel not to be touched.
When the product is carried laid down, 2
persons carry by holding the bottom of the
back, and when it is being put down, put down
carefully for the panel not to be touched.
Transportation method for panel protection
5
ENGLISH
<Correct method>
Panel Cushion
If the product needs to be
set upright, hold both sides
of the product, and tilt back-
ward carefully for the panel
not to touch the floor. (The
setting upright of the set is
possible with the outer frame)
When laying down the prod-
uct, lay a cushion on a flat
floor, and put the product on
it with the panel of the prod-
uct facing down.
<Incorrect method>
Panel
Panel
If the product is tilted to the
side of the panel, the bottom
of the panel may be dam-
aged.
If the product is tilted to the
edge of the panel, the edge
of the panel may be dam-
aged.
Handle the product with care. The product may be damaged by shocks.
NOTE
Storage method for panel protection
6
Before Installation
* Do not use this product for purposes other than to attach the monitor to the wall.
* Be careful when installing and using the bracket to prevent product damage and safety hazards.
* If the instructions in the manual are unclear, stop the installation and contact the service center.
If you are still having problems understanding the instructions after contacting the center, seek a professional to install the product.
* When installing the bracket on a concrete wall or on any other walls capable of holding the strength specified in the manual, you may detach the standard gap
bracket for stud wall mounting then follow the instructions for attaching the bracket to make the installation easier.
* Only install the bracket on vertical walls. Do not install the bracket on a wall inclined at an angle, exceeding the standard range or on the ceiling.
LG Electronics is not liable for problems that occur due to the installation of the product on a slanted wall or on the ceiling.
* Check the accessories provided with the product before installing. LG Electronics is not liable for any damage to or loss of the accessories after the package has
been opened.
* Make sure that the accessories are kept out of reach of children to prevent safety accidents, such as choking due to swallowing small parts.
* Make sure that the screws are fixed tightly.
Applying excessive force to screws may impair the performance or reduce the strength of the product, or cause it to become damaged.
* Make sure that the monitor to be installed does not exceed the specified tension load and that no external force is applied.
* In order to prevent accidents, take care when handling tools during installation of the product.
<Tools for Installation>
Philips screwdriver (manual or electric)/8mm spanner/drill/level meter
How to Attach the Bracket (Stand Type)
7
ENGLISH
Stand Frame Bottom
Stand Frame Vertical
2 Bolts (M8 x 100mm)
1
Attaching the Bottom Stand Frame and Vertical Stand Frame
Fix two bolts in the holes visible from the bottom as illustrated with the arrows.
Insert a nut and then fix a M8 x 15mm bolt.
Then insert one bolt (M8 x 15)
on each side.
Insert one nut
on each side
8
2Attaching the Vertical Stand Frame and Horizontal Stand Frame
Place the horizontal stand frame on top of the angle guide of the vertical stand frame,
insert a nut on each side, then fasten with two M8 x 15mm bolts as illustrated with the arrow.
Then insert one bolt (M8 x 15) on each side.
Insert one nut
on each side
Example of Assembled Stand
Follow the same procedure to fix the nuts and bolts as required.
9
ENGLISH
3Attaching the Horizontal or Vertical Bracket to the Stand
Place the horizontal or vertical bracket on the stand.
2 Screws
(M8X100mm)
Nut
Check the direction of the arrows shown in the figure above to avoid placing the bracket upside down.
CAUTION
10
How to Install (Wall mount type)
NOTE
This manual shows landscape installation. Follow the same procedure for portrait installation.
E-MultiBoard Wall Bracket-Landscape
AB-BL200X
E-MultiBoard Wall Bracket-Portrait
AB-BP200X
Please refer to page 7.
Refer to the following illustration to fix the brackets according to the type.
*Verifying Where the Brackets Are Fixed
A bolt
Use a bolt that is capable of holding the weight of the product.
(The combined weight of the set and the bracket is approx. 60 kg.
We recommend using M8 bolts and nuts.)
The bracket may be distorted depending on the
flatness of the wall. Adjust the flatness of the bracket
using the A bolts attached to it.
This manual suits for next models
4
Table of contents
Other LG TV Mount manuals
