LG LAS454B User manual
SERVICE MANUAL
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT, READ THE “SAFETY PRECAUTIONS”
IN THIS MANUAL.
Internal Use Only
Website http://biz.lgservice.com
2.1 ch Wireless Sound Bar
NOVEMBER, 2015P/NO : AFN77195019
MODEL: LAS454B (LAS454B, S55A3-D)
MODEL: LAS454B
(LAS454B, S55A3-D)
1-1
CONTENTS
SECTION 1 ........ GENERAL
SECTION 2 ........ CABINET & MAIN CHASSIS
SECTION 3 ........ ELECTRICAL
SECTION 4 ........ WIRELESS SUBWOOFER PART
SECTION 5 ........ REPLACEMENT PARTS LIST
1-2
SECTION 1
GENERAL
CONTENTS
ESD PRECAUTIONS......................................................................................................................................... 1-3
WIRELESS SUBWOOFER CONNECTION....................................................................................................... 1-4
HIDDEN KEY MODE ......................................................................................................................................... 1-5
MCS / EQ HIDDEN KEY GUIDE ....................................................................................................................... 1-6
MCS / EQ PROGRAM UPDATE GUIDE........................................................................................................... 1-7
SPECIFICATIONS ............................................................................................................................................. 1-8
1-3
ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated
circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface
such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can
generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER
SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ESD device).
CAUTION. GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS
INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE
SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.
1-4
WIRELESS SUBWOOFER CONNECTION
LED indicator of wireless subwoofer
LED Color Status
Yellow-green
(Blink) The connection is trying.
Yellow-green The connection is completed.
Red
The wireless subwoofer is
in standby mode or the
connection is failed.
Off
(No display)
The power cord of wireless
subwoofer is disconnected.
Setting up the wireless subwoofer
for the first time
1. Connect the power cord of the wireless subwoofer
to the outlet.
2. Turn on the main unit : The main unit and wireless
subwoofer will be automatically connected.
Manually pairing wireless subwoofer
When your connection is not completed, you can see
the red LED or the blinking of yellow-green LED on
the wireless subwoofer and the subwoofer does not
make sound. To solve the problem, follow the below
steps.
1. Adjust volume level of the main unit to minimum by
pressing VOL - button repeatedly until stanby
LED on the main unit blinks slowly.
2. Press and hold (Mute) on the remote control for
about 3 seconds.
- The standby LED on the main unit blinks quickly.
3. If the LED of the wireless subwoofer already blinks
in yellow-green continually, you can skip this step.
Press and hold PAIRING on the back of the
wireless subwoofer for more than 5 seconds.
- The LED of the wireless subwoofer lights up
alternately in red and yellow-green.
4. Disconnect the power cord of the main unit and the
wireless subwoofer.
5. Connect them again after the LED of the main unit
and the wireless subwoofer is fully turned off.
The main unit and the wireless subwoofer will be
paired automatically when you turn on the main unit.
- When the connection is completed, you can see
the yellow-green LED on the subwoofer.
Note
:
•It takes a few seconds (and may take longer) for
the main unit and the subwoofer to communicate
with each other and make sounds.
•The closer the main unit and the subwoofer, the
better sound quality. It is recommended to install
the main unit and the subwoofer as close as
possible and avoid the cases below.
- There is a obstacle between the main unit and the
subwoofer.
- There is a device using same frequency with this
wireless connection such as a medical equipment,
a microwave or a wireless LAN device.
1-5
HIDDEN KEY MODE
HIDDEN MODE KEYS
USB Mode/ UPDATE Main unit ‘- (Volume)’ + Remote control ‘VOL +’
EEPROM EDIT Main unit ‘- (Volume)’ + Remote control ‘CINEMA’
EEPROM CLEAR (Initialize) Main unit ‘- (Volume)’ + Remote control ‘VOICE’
VERSION CHECK Main unit ‘- (Volume)’ + Remote control ‘STANDARD’
CLIP OFF
Main unit ‘-(Volume)’ + Remote control ‘F(Function)’CLIP ON
CLIP ON GAIN MONITERING
MAX Volume Edit
Enter : Main unit ‘- (Volume)’ + Remote control ‘AUTO POWER OFF’
Setting : VOL +/-
Exit : STANDARD
CLIP Algorithm Edit Main unit ‘- (Volume)’ + Remote control ‘VOL -’
Wireless RF Change Main unit ‘- (Volume)’ + Remote control ‘WOOFER LEVEL +’
BYPASS Sound Effect Main unit ‘- (Volume)’ + Remote control ‘DRC ON’
APD Time Display Main unit ‘- (Volume)’ + Remote control ‘DRC OFF’
APD On/Off Main unit ‘- (Volume)’ + Remote control ‘AUTO POWER ON’
Up VOL +
Down VOL -
Right VOICE
Left STANDARD
Enter CINEMA
TV Remote ON Remote control ‘DRC ON’ for 3 seconds.
TV Remote OFF Remote control ‘DRC OFF’ for 3 seconds.
USB Log Out Main unit ‘-(Volume)’ + Remote control ‘ (Power)’
Wireless Demo Mode Main unit ‘-(Volume)’ + Remote control ‘WOOFER LEVEL +’
1
1-6
1. Version & Option Check
※Please connect the Display Jig to the main unit.
1) Power on.
2) Press main unit "-" (volume -) key and remote control STANDARD key during 3 seconds.
3) Check MCS version.
Ex)
4) Press remote control VOICE key 1 time.
Check Wireless Tx version.
Ex)
5) Press remote control VOICE key 1 time.
Check Wireless Rx version.
It’s possible to connect wireless subwoofer.
Ex)
6) Press remote control VOICE key 1 time.
Check EQ version.
Ex)
7) Press remote control VOICE key 1 time.
Check option.
Press remote control VOL + (Up), VOL - (Down), STANDARD (Left), VOICE (Right) key.
Ex)
8) Power cord unplug.
2. EEPROM Initialize
※Please connect the Display Jig to the main unit.
1) Power on.
2) Press main unit “-” (volume -) key and remote control VOICE during 3 seconds.
3) Display VFD “E2P CLR”.
4) Power off automatically.
5) Power cord unplug.
MCS / EQ HIDDEN KEY GUIDE
P1411182
TX150303
RX000000
Q1411170
OP00-00
1-7
1. Preparation
- Diplay Jig.
- Remote control.
- Do format USB Memory to FAT32 File system.
- USB : Update file exist only in the USB Memory stick.
Ex ) LAS454B :
MCS E:\PG540_FW_LAS454B_Ver.bin (if USB driver is E:\)
EQ E:\EQ_PRG.BIN (if USB driver is E:\)
Wireless Tx E:\WIRELESS_TX_150011.bin (if USB driver is E:\)
Wireless Rx E:\WIRELESS_RX_150303.bin (if USB driver is E:\)
2. Update
※Please connect the Display Jig to the main unit.
1) Power on.
2) Press main unit “-” (volume -) key and remote control “VOL +” during 3 seconds. (USB Mode)
3) Insert USB.
4) Display in VFD.
MCS : “MCS UP” “FINISH” Power off.
EQ : “EQ UP” “FINISH” Power off.
Wireless Tx : “UPDATE” “WR XX”(Progress) “FINISH” Power off.
Wireless Rx : “UPDATE” “SEND XX”(Progress) “FINISH” Power off.
5) Loading is shown while updating.
Never remove USB or AC cord.
6) After update finish, show FINISH in VFD and power of automatically.
7) Power cord un-plug.
MCS / EQ PROGRAM UPDATE GUIDE
1-8
SPECIFICATIONS
• GENERAL
Power requirements 120 V ~ 60 Hz
Power consumption 27 W
Networked standby : 0.5 W
(If all network ports are activated.)
Dimensions (W x H x D) Approx. 950 mm x 71 mm x 47 mm
(37.4 inch x 2.8 inch x 1.9 inch)
Net Weight Approx. 2.47 kg (5.4 lb)
Operating temperature 41 °F to 95 °F (5 °C to 35 °C)
Operating humidity 5 % to 90 %
• INPUTS
Digital audio in (OPTICAL IN) 3 V (p-p), Optical jack x 1
Portable in (PORT. IN) 0.5 Vrms (3.5 mm stereo jack) x 1
Available Digital Input Audio
Sampling Frequency 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Available Digital Input Audio format Dolby Digital, DTS Digital Surround, PCM
• AMPLIFIER (RMS OUTPUT POWER)
Total 300 W
Front 50 W + 50 W (4 Ωat 1 kHz, 10% THD)
Subwoofer 200 W (3 Ωat 80 Hz, 10% THD)
• WIRELESS SUBWOOFER (S55A3-D)
Power requirements 120 V ~ 60 Hz
Power consumption 33 W
Type 1 Way 1 Speaker
Impedance 3 Ω
Rated Input Power 200 W
Max. Input Power 400 W
Dimensions (W x H x D) Approx. 171 mm x 390 mm x 261 mm
(6.7 inch x 15.3 inch x 10.2 inch)
Net Weight Approx. 5.6 kg (12.3 lb)
•Designs and specifications are subject to change without prior notice.
2-1
SECTION 2
CABINET & MAIN CHASSIS
CONTENTS
EXPLODED VIEWS ........................................................................................................................................... 2-3
1. MAIN SET SECTION ................................................................................................................................ 2-3
2. WIRELESS SUBWOOFER SECTION...................................................................................................... 2-5
3. PACKING ACCESSORY SECTION ......................................................................................................... 2-7
Other manuals for LAS454B
4
This manual suits for next models
1
Table of contents
Other LG Speakers System manuals
