Lexmoto LX06 User manual

USER’S MANUAL

LX06

（EEC L1e-B）

Welcome to the family of LX06 owners! We will guide you to know each function for the right and safe use of electric scooters.

To ensure your safety, please read this manual carefully before riding and make sure you are always following the requirements below:

Please contact the Local Customer Service Center if you have any questions about this scooter.

We are at our service at any time. Wish you safe and pleasant riding experience!

Fully understand the information in this manual, including but not limited to the relevant instructions, precautions and warnings.

Fully understand the operation and contingency measures of electric scooters.

Be fully aware of warning labels of LX06 electric scooters.

We will not take any responsibility resulting from the unauthorized modiﬁcation, failure to use original spare parts, or installation of components that

affect the performance and safety of the scooter.

1 2

Whether the handlebar is stable and ﬂexible when turning.

Whether the switches on the right and left handlebars can work normally.

Whether the speed accelerator can work normally.

Make sure the tire pressure is normal. The suggested tire pressure is 26-29psi for front wheel and 29-32 psi for rear wheel.

Check tire surface for cracks, damage, wear, and foreign matter puncture or attachment

Whether the tread depth is suffcient (>0.8 mm).

Whether any fault warning light on the instrument panel goes on after being powered.

Whether the battery is fully charged.

Whether the head and tail lights, brake lights and winkers can work normally.

Whether the horn can work normally.

Whether the rear mirrors are clean. Adjust them to the appropriate angle.

Whether the brake oil is suffcient, and whether the handlebars and brake system can work normally.

For any abnormality or operational concern, please contact local Customer Service Center.

Checks Before Riding

Make sure to check the following items before riding a electric scooter, which will guarantee your safety on the road.

RIDING GUIDEUSER INSTRUCTIONS

To ensure the safety of you and others, please make sure to observe the following matters:

Do not ride after you take medications, drink alcohol, or when you are unwell, which may affect your riding ability.

Observe traffic regulations and traffc signs and conﬁrm the surrounding road conditions and scooter conditions at any time to avoid danger.

Wear safety equipment, such as helmet, and appropriate protective clothing if necessary, such as gloves and boots.

Perform a basic check each time before riding, so as to conﬁrm the light, brake, tread and tire pressure and check other parts for looseness or abnormal noise,

and regularly go to Local Service Center for maintenance.

In order to ensure the safety of you and others, please DO NOT use high beam in good lighting conditions. The continuous use of high beam will cause the visual

disturbance to vehicles and pedestrians on the opposite side, thus affecting normal driving.

Please do not make or answer any call during riding, which is likely to cause traffc accidents.

3 4

DESCRIPTION OF COMPONENTS AND PARTS

Installation of Mirrors

Take out the left and right mirrors, insert the hole and rotate the

mirror clockwise to the correct position.

Use the spanner to fasten the nut,make sure the left and right mirror

is on the same line and suitable for the driver’s view.

SAFETY INSTRUCTIONS

35 6

DIAGRAM OF INSTRUMENT PANELDESCRIPTION OF COMPONENTS AND PARTS

Rear direction indicator

Rear combination lamp

Stop lamp/rear position lamp

Converter

Controller

Headlamp

Front position lamp

Speedometer

Rearview mirror

Handle

USB charger

Battery

Horn

Rear registration plate lamp

Direction indicator

Front suspension

Motor

Ⅰ

Brake error

Motor or motor wire error

Handle or handle wire error

Side stand power off

Power on

Accumulated mileage

Mileage unit

Gear position

Low voltage need

recharge the battery

High beam

Temperature

Speed

Battery capacity

lower beam

Turn signal on

Controller error

Details Of Instrument Panel

7 8

SWITCH FUNCTIONOPERATION GUIDE

READY

ECU

Power on

Turn signal on

Meter working temperature

Side stand power off

Controller error

Motor or motor wire error

Brake or brake wire error

Handle or handle wire error

Scooter in P position

Low voltage need recharge the battery

Low voltage for the battery to

the limit level

Lamp Function

High beam on

Gear postion display; single driving time

Speed display, km/h & mp/h switch is available;

external plug switch (off is km/h, on is mp/h)

Battery capacity level

Total milage of the scooter. Speed unit (mile/km)

synchronous switches.

(ODO is accumulated milage.

First showing the accumulated milage and then

single milage with 0000.0. Speed unit (mile/km)

synchronous switches.

Motor error, erase the error and run the

motor for 4 minutes, the error indicator

will disappear automatically.

Lamp Function

Left Start Button Right Start Button

Emergency glasher

Push upward the switch,

all turning lights on and flick,

same display on the meter

Push to left and right to

switch on/off the head lamp.

Press the “ Repair” button to

drive the scooter in low speed

when some motor/controller

errors happens.

Item Switch position Functions

Switch of headlight

Repair button

Near-far light switch

High beam is on when turning

on the button

Low beam is on when turning

on the button

Left turning signal on

Right turning signal on

Horn on

Item Switch position Functions

Indicator control

Horn control

Turn the key to postion and power on the scooter.

ATTENTION:

1. Make sure all lights are in “off” condition, or it may cause power-off protection

due to battery protection programe ;

2. If the power-off protection happen, switch off the lights and restart the circuit

breaker and power on the scooter again.

910

Before riding,make sure the electronic side stand retracted and rotate the handlebar to ensure that the handlebar lock is closed.If the Parking button

is pressed when riding, the bike will be dis- energized. So DO NOT press it when riding for avoiding danger caused by the sudden loss of power.

If the electronic side stand is extended when riding, the bike will be dis- energized. So DO NOT extend the electronic side stand when riding for avoiding

danger caused by the sudden loss of power.

The scooter must be fully stopped before starting. In case of abnormality during riding, please ride carefully or push it to a safe place. DO NOT try

restarting the bike during riding or on the lane so as to avoid danger

OPERATION GUIDE

Guide of ignition key

1Start power supply

OPEN

IGNITION

OFF

OPEN

SHUT

LOCK

Speed levels Press the button to adjust the speed level,

level information will be synchronous shown

in meter

Press the ignition key for 1 second to release the

P gear until the “P” mark in the meter disapper;

The speed regulating function is still effective

when the P gear function is normally turned on;

when the power is on and the whole vehicle stops,

press the P button for 1 second to enter the P gear

postion, the P mark is synchronous in the meter.

Item Switch position Functions

P gear postion

1 2 3

SWITCH FUNCTION

Open the saddle

Handle bar lock and relieve

4The key hole status

Turn the key to left to open the saddle.

1. Turn the handle bar to left until stop;

2. Push the key and turn to left till ( ) position, the handle bar is locked;

3. Push the key and turn to right till ( ) position, the handle bar is unlocked.

1. The key hole is closed when in ( ) position;

2. Turn the key towards to ( ) position，the key hole is in open position.

TIPS:

SHUT

11 12

BATTERY INSTALLATION AND DISMOUNT

Install the cable

Remove the power cord

With the advanced Smart Remote Controller, you can easily lock or unlock your

electric scooter by simply pressing the button within 50 meters.

Unlock

Press the unlock button, and the start button stays on. The scooter enters

into the unlocked state.

Lock

When the scooter is in the static state, press the lock button, and the start

button ﬂashes. The scooter enters the locked state.

Remote keyless entry

After unlock the scooter,press this button twice within two(2) seconds, and

the scooter will be in the “Powered” state without key.

Search key

Press this witch within 50m, “Bi Bi” sounds searching the scooter.

How To Operate The Smart Remote Contol

OPERATION GUIDE

Open the small cap on the top of battery case

Align the power cord with the white arrow on the socket. Insert slowly and press firmly until

you hear a "clicking" sound.

The power plug can be pulled out by rotating the blue buckle ring counterclockwise and

pulling it up with force.

13 14

Guide for side stand power off fuction

Handlebar is short of power, scooter not able to be started.Scooter ON position, scooter can be powered on.

USB & SIDE STAND

Guide of the USB

1. Open the dust cover of the USB charging port;

2. Connect the cable

USB

GUIDE OF THE BREAKER

When the master switch is ON, the vehicle's main power source is connected.

OFF

When the master switch is OFF, the vehicle's main power source is disconnected.

15 16

BATTERY USE INSTRUCTIONS

TIPS:

Short circuit of the cathode and the anode at the battery's input.

Keep it away from children, ﬁre and heat source. It is strictly forbidden

to throw it into the ﬁre; Violent movements, shock and extrusion are

prohibited;

Only the speciﬁed charger can be used, and other chargers are

prohibited to charge the battery;

This product has been subjected to strict inspection before leaving

factory, and it is strictly prohibited to dismantle it. Please contact our

company's after-sales department for any question.

TIPS:

Do not expose the battery to water, and prevent it from being

damped by water or rained.

Charge temperature: 0-45 °C, discharge temperature: -20-45 °C;

Battery capacity will be reduced when placed in a low-temperature

environment;

Charge the battery when you use it, but make sure to charge it before

the capacity is lower than 20%. When it is not used

for a long time, please remove it from the scooter.

Pull up the battery from scooter,insert the main charger plug into the charging socket of the battery. Insert the chargers AC power plug into the home power

socket, and the battery starts charging when the charger indicator turns red.The battery is fully charged if the charger indicator turns from red to green.

BATTERY USE INSTRUCTIONS

Insert the main charger plug into the charging port of the scooter.

Insert the chargers AC power plug into the home power socket, and the battery starts charging when the charger indicator turns red. The battery is fully charged

if the charger indicator turns from red to green.

How to Charge the Battery

Charging Interface

Input power terminal: connect the output charging end and plug

the input power terminal into AC supply.

Output charging end:Before charging, use the output end to

connect the battery, make sue the socket be plugged in

properbly.

Please use the special matching charger for charging, charging

time of a single set battery is normally with in 3~4h.

Input power terminal

2Output charging end

3Power indicator

17 18

Please charge the battery to half-saturation state when storing or transporting it (after the battery is discharged, charge it for 3 hours).

Place it in a dry and ventilated place;

Battery and charger should be kept in a clean,dry,and ventilated place. Keep them away from corrosive materials,power source and heat source;

Storage conditions: ambient temperature -20-35 °C, humidity <65% RH;

When storing the charger, please disconnect it from the battery.

Regular maintenance can enhance the service life and driving safety of the electric scooter. Please refer to the following suggestions and take care of your

scooter.

Storage, Maintenance and Transportation

BATTERY USE INSTRUCTIONS MAINTENANCE

Routine Cleaning and Maintenance

Regular Inspection and Maintenance

Cleaning：Please use clean water and neutral detergent to clean it, and use soft cloths and sponges to clean the surface;

It is prohibited to use metal brushes, sandpaper or the like to clean it, in order not to scratch the parts surface. After cleaning, dry it with soft cloths.

TIPS:

Please disconnect the air switch before cleaning.

Do not use strong water jet to directly wash it, so as to avoid the default of mechanical parts caused by water invasion.

Storage: try to park it in a dry and cool room to reduce the exposure to sun and rain and avoid the reduction of service life due to corrosion of parts.

When left unused for a long time, please turn off the air switch and disconnect the power supply circuitto prevent over discharging.

After long-term storage, please fully charge it before use.

The new scooter must be subject to the ﬁrst inspection and maintenance in the Service Center when it reaches 1,000 km or two months (whichever comes ﬁrst).

The scooter is recommended to be subject to regular inspection and maintenance in the Service Center at every 3,000 km or six months (whichever comes ﬁrst).

Please disconnect the air switch before cleaning.