LESITE LST-TAC User manual
LST-TAC
Roofing Hot Air Welder
Manual
Lesite Technology
LESITE
LST-TAC
Please read this manual carefully before using this machine,
and keep it for future reference.
Application
Overlapping welding of thermoplastic sealing waterproof material
( T P O / F P O 、P V C 、E C B E P D M 、E V A 、P I B 、P M I 、P O 、P P )
Girth Welding
Facade Welding
LESITE
01
EN
Precautions
Please confirm that the machine is turned off and unplugged before
disassembling the welding machine, so as not to be injured by live wires
or components inside the machine.
The welding machine generates high temperature and high,heat, which
may cause fire or explosion when used incorrectly,
especially when it is close to combustible materials or explosive gas,
Please do not touch the hot wedge (during welding work or when the
welding machine has not completely cooled down) so as not to burn.
The power supply voltage must match the rated voltage marked on the
welding machine and be reliably grounded. Connect the welding
machine to a socket with a protective ground conductor.
In order to ensure the safety of the operators and the reliable operation
of the equipment, the power supply at the construction site must be
equipped with a regulated power supply and a leakage protector.
The welding machine must be operated under the correct control of
the operator, otherwise it may cause combustion or explosion due to
high temperature.
It is strictly forbidden to use the welding machine in water or muddy
ground, avoid soaking, rain or damp.
LST-TAC Parameter
LST-TAC Nameplate
Model L ST-TAC
Voltage
Frequency
Power
Welding Speed
Heating Temperature
Weld width
Size( L*W*H)
Net Weight
230 / 120 V
50 / 60 Hz
1700 W
0.5 - 5.0 m/min
50 - 620 ℃
40 mm
270×160×420 mm
5 KG
02
LST-TAC
LESITE
EN
The model identification and serial number identification are marked on
the nameplate of the machine you choose.
Please provide these data when consulting Lesite Sales and Service Center.
LST-TAC Main Parts
1、Nozzle 2、Pressure Roller
3、Handle 4、Main Power Wire
5、Walking Speed Adjustment Knob 6、Moving Switch
7、Hot Air Blower Power Wire 8、Blower Power Switch
9、Temperature Adjustment Knob 10、Hot Air Blower
11、Crawling Wheel
4
5
6
78910
1
2
3
11
03
LST-TAC
LESITE
EN
1、Set the temperature（rotate the temperature adjustment knob（9））.
2、Set the walking speed（rotate the walking speed adjustment knob（5））.
3、Turn on the blower power switch (8）.
4、When the temperature of the air gun reaches the set value, insert the air nozzle（1）
between the upper film and the lower film to be welded（as shown below）.
5、Press the handle（3）with your hand.
6、Turn on the moving switch (6).
7、The machine should pay attention to the pressure roller（2）edge and the relative
position of the edge of the film.
8、After welding, lift the machine slightly and move the air nozzle（1）away from the
welding position.
9、Turn off the moving switch (6).
10、Turn off the air blower power switch (8) after the air blower cools down .
LST-TAC Operations
1、Nozzle 2、Pressure Roller
3、Handle 4、Main Power Wire
5、Walking Speed Adjustment Knob 6、Moving Switch
7、Hot Air Blower Power Wire 8、Blower Power Switch
9、Temperature Adjustment Knob 10、Hot Air Blower
11、Crawling Wheel
04
LST-TAC
LESITE
EN
Routine Maintenance
Quality Assurance
· This product guarantees a 12-month shelf life from the day it is sold to consumers.
We will be responsible for failures caused by material or manufacturing defects. We
will repair or replace defective parts at our sole discretion to meet the warranty
requirements.
· The quality assurance does not include damage to wearing parts (Heating core,
pressure roller, etc.), damage or defects caused by improper handling ormaintenance,
and damage caused by falling products. Irregular use and unauthorized modification
should not be covered by the warranty.
Use steel brush to clean the hot air nozzle
Clean the air inlet at the back of the hot air blower
05
LST-TAC
LESITE
EN
Repairs and Spare Parts
· It is strongly recommended to send the product to Lesite company or
authorized repair center for professional inspection and repair.
· Only original Lesite spare parts are allowed.
06
LST-TAC
LESITE
EN
1
One year
warranty
Lesite Roofing Hot Air Welder 05/2022-EN
FUZHOU LESITE PLASTICS WELDING TECHNOLOGY CO.,LTD
Add: 5# Jingpu Road, Pushang Industry Park,
Cangshan, Fuzhou, 350007, Fujian, China
Tel：+86(591)83818890
E-mail：[email protected]om.cn
Web：www.lesiteweld.com
Table of contents
Other LESITE Welding System manuals
LESITE
LESITE LST700 User manual
LESITE
LESITE LST800 User manual
LESITE
LESITE LST610A User manual
LESITE
LESITE LST900 User manual
LESITE
LESITE LST600A User manual
LESITE
LESITE LST-GM1 User manual
LESITE
LESITE LST-UME User manual
LESITE
LESITE LST-PAU User manual
LESITE
LESITE LST1600 User manual
LESITE
LESITE LST-MAT User manual
Popular Welding System manuals by other brands
TAFA
TAFA 30*8B35 owner's manual
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Technical specifications
ESAB
ESAB Buddy Arc 145 instruction manual
CIGWELD
CIGWELD 636804 use instructions
Red-D-Arc
Red-D-Arc DC-400 Operator's manual
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 owner's manual
