Lehigh E-Flex EFRP-04 User manual

E-Flex

Installation and User Manual

Rev. 1.30

F552

13 November 2017

TECHNICAL INQUIRY

The lighting control system consists of electrical and electronic components which could cause

electrical shock if tampered with. Only individuals experienced with electrical and electronic

equipment should remove the panels or attempt to service this system.

All questions regarding this equipment should be referred to:

Lehigh Electric Products Company

6265 Hamilton Boulevard

Allentown, PA. 18106-9789

Phone 610 395-3386

Fax 610 395-7735

WARRANTY

Subject to the terms of this paragraph, the supplier warrants its title to the products sold by it and

warrants to the Purchaser that its products are free of defects in workmanship or material and are in

conformity with applicable specifications and descriptions of the supplier. No claim shall be maintained

hereunder unless the facts giving rise to it are discovered within 16 months from the date of shipment

from the factory, or 12 months after initial energization of said equipment, with the one expiring first

given precedence, and written notice thereof given to the supplier within 30 days of discovery. The sole

and exclusive liability of the supplier, for Breach of Warranty shall be, at its option, to replace or repair

the product or part concerned F.O.B. its factory or such place as it may designate. The warranties stated

in this paragraph are exclusive of all other warranties, written or oral, statutory, expressed or implied,

none of which shall apply to the sale of the suppliers products hereunder.

0-10V Outputs and Non-isolated Fixture Drivers

Connection of the E-Flex relay panel 0-10V analog dimming outputs to non-isolated fixture drivers is not

recommended. The E-Flex is designed to provide sinking control of fixtures that have a secondary Class 2

dimming circuit that is isolated from the mains power. Connection of the E-Flex 0-10V analog outputs to

non-isolated drivers, or drivers with Class 1 rated dimming circuits, will cause damage to the relay panel.

This damage is considered non-warranty.

Contents

Introduction .................................................................................................................................................. 1

Features and Specification........................................................................................................................ 1

Software Version....................................................................................................................................... 1

Glossary of Terms...................................................................................................................................... 2

Codes/Standards....................................................................................................................................... 3

Safeguards............................................................................................................................................. 3

Warnings and Notices ........................................................................................................................... 3

Installation .................................................................................................................................................... 4

Shipment Inspection ................................................................................................................................. 4

Mounting................................................................................................................................................... 4

Circuit Breaker Protection......................................................................................................................... 4

Terminations and Conduit Access............................................................................................................. 4

Wiring Requirements................................................................................................................................ 5

High voltage Wiring................................................................................................................................... 5

Feed-Through Example –4-circuits, Individual Feeds .......................................................................... 6

Feed-Through Example –4-circuits, Normal/Emergency, 120V and 277V Feeds ................................ 7

Low Voltage Wiring................................................................................................................................... 7

Low Voltage Side Diagram .................................................................................................................... 8

Input Banks –Occupancy, Daylight, Contact Closure, and CapT .......................................................... 9

Demand Response/Timeclock/Emergency Inputs ............................................................................ 9

0-10V Outputs................................................................................................................................. 10

DMX Input .......................................................................................................................................10

E-FlexNet......................................................................................................................................... 10

Controller Power Load Capability ........................................................................................................... 11

E-Flex User Manual, Rev. 1.30

Controller Load Capability...................................................................................................................11

Input Device Unit Loads ...................................................................................................................... 11

Switch Configuration............................................................................................................................... 11

SW1 –Daylight Sensor Inputs .............................................................................................................11

SW2 –Occupancy Sensor Inputs.........................................................................................................11

SW5 –FlexNet Termination ................................................................................................................12

SW6 –DMX Termination.....................................................................................................................12

Emergency Input ................................................................................................................................. 12

Emergency Enable/Disable (EMERG-J12)........................................................................................ 12

Power Up and Configuration ...................................................................................................................... 12

Pre-Check ................................................................................................................................................13

Power Up ................................................................................................................................................ 13

User Interface ............................................................................................................................................. 14

Menu Navigation.....................................................................................................................................14

Input Programming................................................................................................................................. 15

Occupancy Inputs................................................................................................................................15

Navigate to OccX menu................................................................................................................... 15

Set Mode......................................................................................................................................... 15

Set Input Polarity ............................................................................................................................ 15

Assign Zones to Occupancy Input ...................................................................................................16

Set Occupied Preset ........................................................................................................................ 16

Set Un-occupied Preset................................................................................................................... 16

Daylight Sensor Inputs ........................................................................................................................17

Navigate to DayX menu .................................................................................................................. 17

Set Input Polarity ............................................................................................................................ 17

E-Flex User Manual, Rev. 1.30

Assign a Zone to Daylight Sensor Input ..........................................................................................17

Secondary Daylight Zone Adjustment............................................................................................. 17

Contact Closure Inputs........................................................................................................................ 18

Navigate to cciX menu .................................................................................................................... 18

Set Input Polarity ............................................................................................................................ 18

Set Contact Closure Mode .............................................................................................................. 18

Assign Zones to Contact Closure Input ...........................................................................................19

Set Contact Closure Response Preset ............................................................................................. 19

CapT Station Inputs.............................................................................................................................19

Navigate to CapX menu .................................................................................................................. 19

Assign Zones to CapT Input.............................................................................................................19

Set CapT Input Preset for 5-button station..................................................................................... 20

Emergency Input Programming ..............................................................................................................21

Assign Zones to Emergency Input ...................................................................................................21

Set Emergency Zone Levels............................................................................................................. 21

TimeClock/Demand Response Contact Closure Input Programming .....................................................21

Navigate to tcci menu .....................................................................................................................21

Set Input Polarity ............................................................................................................................ 21

Set Timeclock Contact Closure Mode ............................................................................................. 22

Assign Zones to Timeclock Contact Closure Input ..........................................................................22

Set Timeclock Response Preset....................................................................................................... 22

Set Demand Response Fade Time................................................................................................... 23

Set Demand Response Load Shed Values ....................................................................................... 23

DMX Setup .............................................................................................................................................. 24

Set DMX Start Address.................................................................................................................... 24

E-Flex User Manual, Rev. 1.30

Assign Zones to DMX Input ............................................................................................................. 25

Set DMX Input for Impress Link and Area.......................................................................................25

Load setup............................................................................................................................................... 26

Set Load Type..................................................................................................................................26

Set Low End Trim and relay cutoff ..................................................................................................26

Set High End Trim............................................................................................................................ 27

Preset Edit...............................................................................................................................................28

Control/Test ............................................................................................................................................29

Navigate to Control menu...............................................................................................................29

Clear Memory .................................................................................................................................29

DMX Loss Behavior .........................................................................................................................29

Relay Test........................................................................................................................................ 30

Ramp Test ....................................................................................................................................... 30

Relay Override................................................................................................................................. 30

Device ID .........................................................................................................................................31

DASC –Daylight Scaler, Primary/Secondary Daylight Zone Adjustment ........................................ 31

Default Configuration .................................................................................................................................32

Input Assignments ..................................................................................................................................32

Occupancy...........................................................................................................................................32

Daylight ............................................................................................................................................... 32

Contact closure ................................................................................................................................... 32

CapT .................................................................................................................................................... 33

Emergency...........................................................................................................................................33

Timeclock ............................................................................................................................................33

Preset Levels ........................................................................................................................................... 33

E-Flex User Manual, Rev. 1.30

DMX Addressing and Zone Assignment..................................................................................................33

Load Setup .............................................................................................................................................. 33

DMX Loss Behavior ................................................................................................................................. 33

RDM Implementation .................................................................................................................................34

Blank Configuration Chart........................................................................................................................... 35

Introduction

This document provides an installation guide and user operation manual for the E-Flex relay panel. The

E-Flex relay panel is designed for 120-277V AC, 47-63 Hz installations providing controlled switching of

four or eight zones as well 0-10V dimming. Inputs for occupancy and daylight sensors provide for

standalone energy management.

The following E-Flex relay panel models are available:

EFRP-04, 4 relays and 0-10V dimming

EFRP-08, 8 relays and 0-10V dimming

Features and Specification

Surface mount enclosure

4 or 8 mechanically latching relays with the following ratings:

oResistive: 50A @ 277VAC, 20A 347VAC

oTungsten: 20A @ 240 VAC, 277VAC

oStandard Ballast: 20A @ 120VAC, 277VAC, 347VAC

Electronic Ballast: 16A @ 120VAC, 277VAC

4 or 8, 0-10V outputs with current sink of 80mA.

Integrated +24V DC power supply to provide power for sensors and E-FlexNet devices.

Dry contact closure inputs for UL924, timeclock, fire alarm, and demand response.

4 banks of inputs for occupancy, daylight, and contact closure.

19 presets plus OFF for up to eight zones.

DMX512 input with RDM (Remote Device Management) support as well as Impress link mode to

support SDE impress remote stations.

Software Version

The features and user interface described in this manual are supported with E-Flex software versions

V1.05 and higher.

E-Flex User Manual, Rev. 1.30

Glossary of Terms

Demand Response -

Energy codes and energy companies have growing requirements to reduce your power consumption

during high-energy usage. The Room Controller meets these energy requirements by accepting a contact

input from the power company to impose a maximum output per zone.

LightsOut -

LightsOut is the period of time when lights should be at the LightsOut preset (typically, Off) unless there

is user intervention. Before activation of the LightsOut preset, lights will flash three times to warn

occupants of the upcoming change. After a delay the LightsOut preset will be activated. During this

delay, any button press at any station will further delay the activation of the LightsOut preset. Once the

LightsOut preset is in effect, light levels may be changed by a user. After 15 minutes of no inactivity, the

LightsOut sequence will start again.

Occupancy Mode –

Automatically turn lights ON when the occupancy sensor input detects the presence of a person and will

automatically turn lights OFF when no presence is detected for a specified amount of time.

Vacancy Mode –

Lights must be turned on manually by someone entering a room or area. The system will then

automatically turn lights OFF when no presence is detected on the occupancy sensor input for a

specified amount of time.

This manual suits for next models

Table of contents

Other Lehigh Relay manuals

Lehigh

Lehigh E-Flex EFRP User manual

Popular Relay manuals by other brands

Shelly

Shelly Pro Series user manual

GE MVAX 11 Technical manual

ABB

ABB RELION REF615R manual

Pilz

Pilz PNOZ X10 Technical instructions

ABB

ABB SPAJ 142 C User manual and technical description

Kemo Electronic

Kemo Electronic B197 quick guide

Seg

Seg MRM3 manual

Basler

Basler BE1-700C manual

CD Automation

CD Automation REVEX 2PH 280A user manual

Ruelco

Ruelco 1S04 Operation manual

Basler

Basler V3E Z1P B2C1F instruction manual

Doepke

Doepke Dupline DSM 2 operating instructions

Siemens

Siemens SIRIUS 3RT1966-4D Original operating instructions

GE DGP instruction manual

Kyongbo Electronics

Kyongbo Electronics GDR-D01 user manual

Siemens

Siemens SIPROTEC 4 user manual

Siemens

Siemens BD2-AK03X/FS Series installation instructions

Leuze

Leuze MSI-SR5B Original operating instructions