LEGRAND Kenall T8 Series User manual
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
1
INSTALLATION INSTRUCTIONS
T8-LED_F-5591_091118
LED Retrofit Luminaire
T8-LED
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS
BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH
ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT
TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS
AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.
SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE
FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING
ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
T8 SERIES – LED
WARNING – Risk of re or electric shock.T8-LED Retrot Kit installation requires knowledge of luminaires electrical systems. If not
qualied, do not attempt installation. Contact a qualied electrician. Install this kit only in the luminaires that have the construction
features and dimensions shown in the photographs and/or drawings.
Install this retrot kit only in Kenall luminaires designed for 4' uorescent T8 G13 (medium bi-pin) lamps, operating at a voltage of
120-277VAC, 50/60Hz, and where the input rating of the retrot kit does not exceed the input rating of the luminaire. Existing lamp
holder sockets and wires within the xture are retained; lamp holder sockets may be either shunted or non-shunted type, (instant start or
programmed\rapid start). Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. Inspect lamp
holder sockets for damage; replace any damaged components prior to retrot kit installation. Do not disconnect existing wires from lamp
holder sockets - connections will be made to existing lamp holder wiring by cutting existing lamp holder leads away from the lamp holder
and make new electrical connections to lamp holder lead wires by employing supplied wire connectors.
IN CANADA -
WARNING – risk of re or electric shock. Installation of this retrot assembly requires a person familiar with the construction and
operation of the luminaire’s electrical system and the hazard involved. If not qualied, do not attempt installation. Contact a qualied
person.
AVERTISSEMENT – risque d’incendie ou de choc électrique. L’installation de ce nécessaire de modernisation exige une personne familière
avec la construction et le fonctionnement du système électrique du luminaire et des risques associés. Toute personne qui n’est pas qualiée
ne doit faire aucune tentative d’installation et doit contacter une personne qualiée.
WARNING – risk of re or electric shock. Install this kit only in the luminaires that has the construction features and dimensions shown in
the photographs and/or drawings and where the input rating of the retrot kit does not exceed the input rating of the luminaire.
AVERTISSEMENT – risque d’incendie ou de choc électrique. N’installer ce nécessaire que dans les luminaires dont les caractéristiques de
construction et les dimensions sont conforme à celles illustrées dans les photos et/ou les dessins et dont la puissance d’entrée nominale du
nécessaire de modernisation ne dépasse pas celle du luminaire.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
Il est interdit de faire ou de modier une ouverture dans un boîtier de câblage ou de composants électriques au cours de l’installation du
nécessaire.
This retrot kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities
having jurisdiction.
Le nécessaire de modernisation est accepté à titre de composant d’un luminaire lorsque la pertinence de la combinaison doit ëtre
déterminée par par les autorités compétentes
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
2
INSTALLATION INSTRUCTIONS
T8-LED_F-5591_091118
Retrot Kit contents:
• (2) 4’ T8-LED lamp tubes
• (1) T8-LED driver
• (2) Five Wire Connectors
• (1) POSITIVE label
• (1) NEGATIVE label
• (1) LAMP REPLACEMENT label
• (1) RETROFIT label
1. Cut power to luminaire.
2. Open luminaire door (if equipped.)
3. Depending on xture design, remove reector\diffuser assembly. (see Figure 1)
4. Remove uorescent lamps.
5. Remove luminaire wireway access cover.
6. Look at uorescent ballast, and determine if ballast is either ‘Instant Start,’ or ‘Programmed\Rapid Start.’ This information is usually
found on the ballast data label. Save this information for step 9 and 10.
7. Cut all wires connected to the uorescent ballast. Cuts should be close (3-4") to the ballast, and not include any pre-existing splices.
Strip ends of xture wires approx. 3/8". Remove ballast.
8. Install LED driver in luminaire, using the existing uorescent ballast mounting. Note: ONLY install Kenall LED driver provided with this
kit; use of a different driver may damage the LED lamp tubes and void warranty.
9. Wire LED driver to lamp holder sockets:
10. If ‘Instant Start’: (see above step 5) insert cut RED wire into (+) RED wire\connector of LED driver. Insert cut BLUE wires into (-) BLUE
wire\connector of LED driver. (See diagram 1)
11. If ‘Programmed\Rapid Start:’ (see above step 5) insert cut RED and BLUE wires into (+) RED wire\connector of LED driver. Insert cut
YELLOW wires into (-) BLUE wire connector of LED driver. (See diagram 2)
12. Wire LED driver to line power: (See diagram 3) depending on driver, connect LED driver GREEN wire to xture ground. If no GREEN
wire is present on LED driver, disregard - the LED driver is case grounded. Connect LED driver BLACK wire to xture (BLACK or
ORANGE) line wire (120-277VAC, 50/60Hz only.) Connect LED driver WHITE wire to xture (WHITE) neutral wire.
13. Attach xture retrot labels: (see gure 2) Refer to wiring, and identify positive and negative lamp holder socket brackets. Apply
POSITIVE (+) label in a conspicuous location to positive lamp holder socket bracket. Apply NEGATIVE (-) label in a conspicuous
location to negative lamp holder socket bracket. Attach LAMP REPLACEMENT label next to, or close to original xture data label. Do
not cover existing label. Apply
RETROFIT label in a conspicuous location on xture. (e.g., on internal reector or diffuser assembly,
visible during re-lamp or service)
14. Install LED lamp tubes. Caution: Correct LED lamp polarity must be observed during installation and
operation. Failure to install LED lamp tubes with the correct polarity may damage lamp tubes and LED driver.
(See Figure 3) Note positive and negative ends of LED lamp tube; install positive and negative ends with corresponding positive and
negative lamp holder socket brackets. Ensure LED lamp tube is installed with
frosted or clear lens aimed toward illuminated surface.
15. Install luminaire wireway access cover.
16. Install reector\diffuser assembly.
17. Close luminaire door.
18. Apply power; check for proper operation.
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
3
INSTALLATION INSTRUCTIONS
T8-LED_F-5591_091118
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
4
INSTALLATION INSTRUCTIONS
T8-LED_F-5591_091118
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
5
INSTALLATION INSTRUCTIONS
T8-LED_F-5591_091118
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
6
INSTALLATION INSTRUCTIONS
T8-LED_F-5591_091118
For technical assistance, call 1-800-4KENALL (1-800-453-6255).
WARRANTY
CUSTOMER SERVICE
For warranty information visit www.kenall.com/Resources/Certied-Performance-Warranties
This manual suits for next models
1
Table of contents
Other LEGRAND Lantern manuals
LEGRAND
LEGRAND LUXTRAN LTSIU Series User manual
LEGRAND
LEGRAND Kenall TEKDEK TD17 Series User manual
LEGRAND
LEGRAND Kenall LUXTRAN LTL Series User manual
LEGRAND
LEGRAND Kenall LUXTRAN LTSI Series User manual
LEGRAND
LEGRAND Kenall LUXTRAN LTS Series User manual
LEGRAND
LEGRAND B65 LED User manual
LEGRAND
LEGRAND Finelite HP-4 User manual
LEGRAND
LEGRAND Kenall Nova Series User manual
LEGRAND
LEGRAND 6 601 42 Instruction Manual
LEGRAND
LEGRAND 0 643 60 User manual
