Ledj Event Panel User manual

www.prolight.co.uk

LEDJ Event Panel

(Order code: LEDJ68)

User Manual

LEDJ Event Panel Safety

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

LEDJ Event Panel Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is fully charged

Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v. (for charging only)

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

LEDJ Event Panel Over view

Over view:

Operation:

After the unit is powered up, Press the “MODE” button to activate the main menu:

Built-in programmes, Auto run, DMX, Slave or Sound active mode.

“SETUP” button is to change the current mode.

“UP” button is to increase the value of the current setting.

“DOWN” button is to decrease the value of the current setting.

Built-in programmes: Runs one of the 12 built-in programmes.

Auto run: Runs the built-in programmes in a continuous loop.

DMX mode: The unit can be controlled by any universal DMX controller.

Slave mode: The units in this mode can be synchronously run with a Event Panel

set to master mode.

Sound activated mode: Runs via sound activation using the built-in microphone

Built-in programmes mode:

With the LEDJ Event Panel, you can select 12 different Programmes. Press the “SETUP” and

“UP” and “DOWN” buttons to select the programmes (from PG01 to PG12) and select the desired

programme value. When the LED display shows PG.01, press the “SETUP” button for the

rst time, and it will show CL0.0 you can now select one of the 7 static colours by using the

“UP” and “DOWN” buttons; then press the “SETUP” button for the second time, and it will show

FS.00, you can now select your desired ash frequency by using the “UP” and “DOWN”

buttons. When in PG.11 and PG.12, press the “SETUP” button for a third and fourth time, and

it will show C1.-1, or C2.-2 and now you can choose two colours for the programmes to work

in, using the “UP” and “DOWN” buttons.

When in programmes PG.02 - PG.10 , press the “SETUP” button for the rst time, and it will

show SP.99, you can now set the running speed for this programme. Then press the “SETUP”

button for a second time, and it will show FS.00, you can now select the ash frequency for it

using the “UP” and “DOWN” buttons.

SP: Speed 00-99 (00 = slow, 99 = fast)

FS: Flash frequency from 00-99 (00 = slow, 99 = fast)

LEDJ Event Panel Over view

Auto Run mode:

To access the Auto run mode, Press the “MODE” button until the LED display shows AU70.,

then press the “SETUP” button and it will show N.OO1, you can now select the programme

running times by using the “UP” and “DOWN” buttons. Programme Running times N.001 - N.100

Note: The Programme running time indicates how many times the running programme is repeated

before moving on to the next one.

DMX Mode

To control the Event Panel individually via your DMX controller, press the “MODE” button untill

is shown on the LED display, it is now in DMX mode. Now press the “SETUP” button so

the LED display shows .001, this now means that the DMX address is set at 001. You can

select your DMX address by using the “UP” and “DOWN” buttons. If you press the “SETUP”

button the LED display will show: 03.Ch., 06C.h.,12.ch., 24.ch., or p4.ch.

this selects which DMX mode the Event Panel is being run in. You can select any of these 5 DMX

modes by using the “UP” and “DOWN” buttons.

DMX Values

03CH

06CH

12CH

DMX Values (cont..)

24CH

P4CH

Slave Mode:

To activate the Slave Mode, press the “MODE” button to show SlA-, this will now run

the Event Panel in slave mode.

Sound Mode:

To activate the Sound Mode, press the “MODE” button to select SO.31, now the sound mode is

activated it will run one step at a time, you can adjust the sensitivity by using the “UP” and “DOWN”

buttons. (Sensitivity: SO01 - SO31, 01 = low, 31 = high). Press the “SETUP” button and it will

show Nn-1, this is sound mode 1 (running static colour 1 step, 1 time) use the “UP” and “DOWN”

buttons to select sound mode 2 Nn-2, (running dimming colours 1 step, 1 time)

CH3

0 - 255: G

LEDJ Event Panel Over view

CH1

0 - 255

RED 1

CH2

0 - 255

GREEN 1

CH3

0 - 255

BLUE 1

CH22

0 - 255

RED 8

CH23

0 - 255

GREEN 8

CH24

0 - 255

BLUE 8

CH1

0 - 18:

19-37

38-56

57-75

76-94

95-113

114-132

133-151

152-170

171-189

190-208

209-227

228-246

247-255

CH2

0 - 255: R

CH4

0 - 255: B

Functions

RGB Dimmer

PG02 - Colour dream

PG03 - Colour fade

PG04 - Colour change

PG05 - Colour jump

PG06 - Flow 1

PG07 - Flow 2

PG08 - Chase 1

PG09 - Chase 2

PG10 - Multi-colour

PG11 - Chase 3

PG12 - Chase 4

Sound active0-255 Sensitivity Not used Not used

0-255 select colour

Not

Used

0-255

Flash

Speed

0-255

Running

Speed

PG01 - Static colour

Operation For Battery Pack

1, Press the Transmitting mode button for more than 3 seconds, until the transmitting signal light is

“ON”, then it means this unit is transmitting. If you want this unit to be the receiver, then you can

press the Receiving mode button for more than 3 seconds until the receiving signal light is “ON”.

2, The UP and DOWN buttons are for selecting different channel frequencies of the

battery pack.

For example, if you have 10 transmitters and 10 receivers, you can press the UP and DOWN

buttons to set their channel frequency accordingly. There are 125 to choose from.

3, When you are charging the battery pack the “Charging LED” will illuminate Red and once

the battery pack is fully charged, the “Charging signal light” will turn Green and the LED Event

Panel is now ready for use.

Note:

1, When using the battery to power the event panel, do not connect the 110V-240V power cable

2, When the battery is fully charged, it can supply a single colour on full output on the

LED Event Panel for about eight hours.

3, Please make sure you connect all necessary cables before operation.

4, Please recharge it immediately after discharge.

LEDJ Event Panel Operation For Battery Pack

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The LEDJ Event Panel can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Equinox Event Panel DMX set up

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

LEDJ Event Panel DMX Set Up

Features:

DMX Channels: ....................................................................................... 3/4/6/12 or 24 selectable

Display: ................................................................................................4 Push button LED display

Connections: .........................................................................................3-Pin XLR In/Out for DMX

Operations: ...............................Built-in programmes, Auto run, Sound active, Slave and DMX

LEDs: ...........................................................288 Ultra Bright 10mm LEDs (R: 48, G: 120, B: 120)

Beam angle: ...................................................................................................................40 degrees

Wireless DMX: .......................................................................................................On battery pack

Panel specications:

Power consumption: .................................................................................................................36W

Power supply: ...........................................................................................110V - 240V 50Hz/60Hz

Dimensions: ........................................................................................................420 x 265 x 65mm

Weight: ...................................................................................................................................3.0Kgs

Battery pack specications:

Power supply: ...........................................................................................................................240V

Dimensions: ......................................................................................................325 x 240 x 120mm

Weight: ...................................................................................................................................8.0Kgs

LEDJ Event Panel Features

Table of contents

Other Ledj Lighting Equipment manuals

Ledj

Ledj Aspect XL LEDJ302 User manual

Ledj

Ledj STRATOS UV User manual

Ledj

Ledj Stage Par CZ 120 RGBA User manual

Ledj

Ledj Aspect XL User manual

Ledj

Ledj LED RGB 252 User manual

Ledj

Ledj Pixel Storm 6 Tri Batten User manual

Ledj

Ledj LEDJ352A User manual

Ledj

Ledj LEDJ251 User manual

Ledj

Ledj LEDJ24 User manual

Ledj

Ledj LEDJ472 User manual

Ledj

Ledj LEDJ188 User manual

Ledj

Ledj SPECTRA PAR 7T3 User manual

Ledj

Ledj STAR15 User manual

Ledj

Ledj Slimline 7HEX6 Series User manual

Ledj

Ledj Rapid QB1 RGBW Battery Uplighter User manual

Ledj

Ledj SPECTRA PAR 7T3 User manual

Ledj

Ledj Slimline 12Q5 Series User manual

Ledj

Ledj Event Spot Bar RGBW User manual

Ledj

Ledj LEDJ255 User manual

Ledj

Ledj Spectra Flood 18HEX10 User manual

Ledj

Ledj SPECTRA BATTEN12T3 EXTERIOR User manual

Ledj

Ledj ALU ZOOM PAR 64 User manual

Ledj

Ledj TRI LED-56 CAN User manual

Ledj

Ledj Spectra Q40 MKII User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions